Grain size effect on behaviour and microstructure of a warm deformed Ti-IF steel

The effect of grain size on the deformation behaviour in the fenite region of a Titanium stabilized Interstitial Free steel was investigated by hot torsion. The initial work hardening regime is followed by a softening regime where a broad peak stress develops. The peak stress and the stress at final strain were relatively insensitive to grain size. However, at low values of the Zener-Hollomon parameter, the strain to the peak stress was strongly dependent on the grain size. A series of microstructural parameters were examined to explain these observations.

Influence of grain size on the compressive deformation of wrought Mg-3A1-1Zn

The influence of the grain size on the flow stress of extruded Mg–3Al–1Zn tested in compression is examined. Samples with grain sizes varying between 3 and 23 μm were prepared by altering the extrusion conditions. Compression testing of the extruded bar was carried out at temperatures between ambient and 200 °C. Twinning dominated the deformation at lower temperatures but this gave way to slip dominated flow when the temperature was raised. For tests carried out at intermediate temperatures, a similar transition was observed when the grain size was reduced. The transition was accompanied by a change in flow curve shape and Hall–Petch slope. The peak stresses achieved when twinning dominated the deformation were up to 100 MPa greater than those seen when slip dominated the flow. Critical grain sizes marking the twinning–slip transition were identified and these are described in terms of the deformation conditions.

Influence of grain size on hot working stresses and microstructures in Mg-3A1-1Zn

The influence of the grain size on the deformation of Mg–3Al–1Zn was examined in compression at 300 °C. At low strains the flow stress increases with increasing grain size. This is interpreted in terms of dynamic recrystallization. Empirical models of dynamic recrystallization are developed and employed to generate a microstructure map.

Effect of grain size on the deformation and dynamic recrystallization of mg-3AI-1Zn

The influence of grain size on the deformation of extruded Mg-3Al-1Zn tested in tension at temperatures between room temperature and 300°C is investigated. The results enable estimation of the deformation conditions for the transition from slip to twinning dominated flow and for the initiation and completion of dynamic recrystallization. A map illustrating these critical parameters is constructed and it is shown that the operating conditions of the common wrought processes straddle key transitions in microstructure behaviour.

Grain size effect on the warm deformation behaviour of a Ti-IF steel

The effect of grain size on the warm deformation behaviour of a titanium stabilized interstitial free (IF) steel was investigated using hot torsion. The initial work hardening regime is followed by the development of a broad stress peak after which work softening occurs. The hypothetical saturation stress (Estrin–Mecking model) and the stress at final strain were relatively insensitive to grain size. However, the strain to the peak stress was strongly dependent on the grain size at low values of the Zener–Hollomon parameter. A simple phenomenological approach, using a combined Estrin–Mecking model and an Avrami type equation, was used to model the flow curves. The hypothetical saturation stress, the stress at final strain and the strain to peak stress were modelled using three different hyperbolic sine laws. A comparison with independent data from the literature shows that the apparent activation energy of deformation determined in this work (Q=372 kJ/mol) can be used to rationalize the steady-state stress in compression data found in the literature.

Numerical investigation of austenite grain size distribution in square-diamond pass hot bar rolling

In this study, the austenite grain size (AGS) for hot bar rolling of AISI4135 steel was predicted based on two different AGS evolution models available in the literature. In order to predict the AGS more accurately, both models were integrated with a three-dimensional non-isothermal finite element program by implementing a modified additivity rule. The predicted results based on two models for the square-diamond (S-D) and round-oval (R-O) pass bar rolling processes were compared with the experimental data available in the literature. Then, numerical predictions depending on various process parameters such as interpass time, temperature, and roll speed were made to compare both models and investigate the effect of these parameters on the AGS distributions. Such numerical results were found to be beneficial to understand the effect of the microstructure evolution model on the rolling processes better and control the processes more accurately.

Grain size in Mg alloys: recrystallization and mechanical consequences

The present paper examines the development of grain size during the recrystallization of magnesium alloys and the influence the grain size has on the mechanical response. In magnesium alloys grain refinement improves the strength-ductility balance. This simultaneous increase in both strength and ductility is ascribed to the impact the grain size has on deformation twinning. The mechanisms by which the grain size is established during hot working are shown to be conventional dynamic recrystallization followed by post-dynamic recrystallization. The role of alloying additionon both of these reactions is briefly considered.

Analytical model of pass-by-pass strain in rod (or bar) rolling and its applications to prediction of austenite grain size

Rod rolling is a process where the deformation state of the workpiece between the work rolls is quite different from the strip rolling process. However, in most microstructure evolution models, the simple area strains (natural logarithm of the area reduction ratio) multiplied by a constant have been used to compute pass-by-pass evolution of austenite grain size (AGS) in rod (or bar) rolling, without any verification. The strains at a given pass play a crucial role in determining the recrystallization behavior (static or dynamic). In this study, an analytical model that calculates the pass-by-pass strain and strain rate in rod rolling has been developed and verified by conducting four-pass (oval–round) bar and plate rolling experiments. Numerical simulations have then been carried out for the four-pass rolling sequence using the area strain model and the new analytical model, focusing on the effect of the method for calculating the strain on the recrystallization behavior and evolution of AGS. The AGS predicted was compared with those obtained from hot torsion tests. It is shown that the analytical model developed in this study is more appropriate in the analysis of bar (or rod) rolling. It was found that the recrystallization behavior and evolution of AGS during this process were influenced significantly by the calculation method for the deformation parameters (strain and strain rate). The pass-by-pass strain obtained from the simple area strain model is inadequate to be used as an input to the equations for recrystallization and AGS evolution under these rolling conditions.

Local Austenite grain size distribution in hot bar rolling of AISI 4135 Steel

In this paper, the local distribution of austenite grain size (AGS) was experimentally determined by conducting single round-oval and square-diamond pass hot bar rolling experiments of AISI4135 steel. The rolling experiments were carried out using the laboratory mill. The local distribution of AGS was also determined numerically. In order to predict AGS distribution, the AGS evolution model was combined with three dimensional non-isothermal finite element analyses by adopting a modified additivity rule. AGS evolution model was experimentally determined from hot torsion test according to Hodgson's model. The predicted results were in a reasonably good agreement with experimental results.

A rationale for the strong dependence of mechanical twinning on grain size

In metals that yield as a consequence of mechanical twinning, the yield stress is a function of the grain size in much the same way as it is for dislocation glide. However, the sensitivity to grain size is typically greater. The intent of the present communication is to show that this can be understood, at least in part, in terms of a size effect that accompanies twinning. Some confirmatory data from a magnesium alloy are presented.

Dependency of recrystallization mechanism to the initial grain size

The effect of initial grain size on the recrystallization behavior of a type 304 austenitic stainless steel during and following hot deformation was investigated using hot torsion. The refinement of the initial grain size to 8 μm, compared with an initial grain size of 35 μm, had considerable effects on the dynamic recrystallization (DRX) and post-DRX phenomena. For both DRX and post-DRX, microstructural investigations using electron backscattered diffraction confirmed an interesting transition from conventional (discontinuous) to continuous DRX with a decrease in the initial grain size. Also, there were unexpected effects of initial grain size on DRX and post-DRX grain sizes.