Understanding in-vivo abrasion fatigue or common suture materials used in arthroscopic and open shoulder surgery

In orthopaedic surgery the reattachment of tendon to bone requires suture materials that have stable and durable properties to allow healing at the tendon-bone interface. Failure rates of this type of surgery can be as high as 25%. While the tissue suture interface is a weak link, proportions of these failures are caused by in-vivo abrasion of the suture with bone and suture anchor materials. Abrasion of the suture material results from the movement of the suture through the eyelet by the surgeon during surgery, or with limb movement after surgery as the suture is not rigidly restrained within the eyelet. During movement the suture is subjected to bending and frictional forces that can lead to fatigue induced failure. This paper investigates the mechanism of bending abrasion fatigue induced failure of number two grade braided sheath only and braided sheath/multifilament core sutures. Sutures were oscillated over a stainless steel wire at low frequency under load in a dry state to simulate the bending and frictional forces between suture and eyelet. Failure mechanism was determined by video microscopy of the suture during abrasion combined with optical microscopy analysis of partially and fully abraded sutures. Braided only structures had high friction loading on the small number of fibres at the abrasion interface. This caused rapid single fibre breakages that accumulate to cause suture failure. The addition of ultra-high molecular weight polyethylene core fibres to a braided suture distributed the applied load across multiple fibres at the abrasion interface. This improved abrasion resistance by 15-20 times that of braided sheath alone.

Improved incorporation of fibres for more abrasion resistant yarns

Rubbing of the fibrous strand after drafting, but before twist insertion improves the incorporation of surface fibres. The method delivers the benefits of a small spinning triangle like compact spinning and improved fibre trapping like siro and solo spinning. The yarns produced are less hairy and more resistant to degradation in downstream processing. This can improve the weavability of the yarns, reduce the sizing costs and increase service life of the fabrics by making them more resistant to wear and pilling.

Performance comparison of abrasion resistant textile motorcycle clothing

 Falling at speed onto a tarmac surface during cycling can cause abrasion and laceration of the skin and body tissue. Motorcycle clothing designed to reduce or avoid this type of injury has traditionally been made of animal leather as it has well known resistance to abrasion. In the last 20 years there has been an emergence of textile clothing reinforced with high performance/tenacity fibres such as those made from polyamides, aramids, ultra high molecular weight polyethylene and liquid crystal. Almost no comparative work has been undertaken to provide insight into the level of protection these clothing layers can provide.
This work has used a CE standard test method to evaluate a number of abrasion resistant textile pant products and compare them with a leather race product. It analysed the protective fabric layer structure for mass, thickness, construction method and resistance to abrasion.
Structures manufactured from high tenacity fibres performed better than those from lower tenacity ones. Fabric construction method and mass per unit area were the two key variables in providing an abrasion protective layer. Structures manufactured from knitted para-aramid fibres performed better than their woven counterparts due to the method of fabric failure. Several well designed protective layers performed at a similar level to that of leather; however, most garments tested failed to meet the lower level European standard of abrasion resistance (CE level 1), which may put their wearer at risk in the advent of a collision.

Impact abrasion resistance quantification of protective motorcycle gloves

The hands are often the first contact point with the road surface in a motorcycle crash. Wearing well designed protective gloves has been proven to significantly reduce the occurrence and severity of injuries to the hand. The European Standard for motorcycle protective gloves requires testing of component materials separately and does not consider the impact of abrasive surfaces on seems. This work aimed to develop a new method of testing of fully constructed gloves as worn by a rider in impact abrasion situations. It used previously published fall mechanics to understand the areas that may undergo impact abrasion. It defines the important zones for abrasion resistance and details ideal impact/measurement geometry for measurement on a Cambridge type abrasion tester. It proposes a method for the impact abrasion resistance of the palm, knuckles, wrist, outer side of the little finger and the tops of fingers. This information may be used for the quantification of fully manufactured gloves for standard certification or use in a rating system.

Permian brachiopods from the Selong Xishan section, Xizang (Tibet), China. Part 2: palaeobiogeographical and palaeoecological implications, spiriferida, athyridida and terebratulida

Brachiopods from the Selong Group at the Selong Xishan section indicate a typical Peri-Gondwanan affinity, but possibly a rapid invasion of tropical/subtropical Tethyan elements into the Himalayan region at the very end of Permian. A brief analysis of taphonomy and composition of the Selong fauna indicate that Selong Xishan lay on the shallow continental shelf near shore and brachiopods suffered substantial abrasion from contemporaneous wave action. Species of Spiriferida, Athyridida and Terebratulida are herein described and revised. New taxa are Nakmusiella selongensis nov. gen. et sp. and ? Bullarina striata nov. sp.

Effect of synthesis parameters on the electrical conductivity of polypyrrole-coated poly(ethylene terephthalate) fabrics

The effects of pyrrole, anthraquinone-2-sulphonic acid (AQSA) and iron(III) chloride (FeCl3) concentrations, reaction time and temperature on the electrical conductivity of polypyrrole (PPy) - coated poly(ethylene terephthalate) (PET) fabrics were investigated. With an increase in both the AQSA and FeCl3 concentrations, resistivity decreased to a point beyond which higher concentrations led to increased surface resistivity. Erosion of the polymer coating, in dynamic synthesis from continual abrasion, manifested as an exponential increase in the resistance of the coated textile substrate. This was not encountered in static synthesis conditions. Temperature affected the degree of surface and bulk polymerisation. The effect of polymerisation temperature on conductivity was negligible. Conductive polymer coating on textiles through chemical polymerisation enabled a smooth coherent film to encase individual fibres, which did not affect the tactile properties of the host substrate. The optimum FeCl3/pyrrole and AQSA FeCl3/pyrrole molar ratios were found to be 2.22 and 0.40 respectively.

Polymerising pyrrole on polyester textiles and controlling the conductivity through coating thickness

The surface resistance of polypyrrole (PPy)-coated polyester fabrics was investigated and related to coating thickness, which was controlled by adjusting the reactant concentrations. The thickness of the coating initially increased rapidly followed by a steady increase when the concentration of pyrrole (Py) was larger than a concentration of approximately 0.4 mg/ml. The surface resistance decreased from 10⁶ to 10³ Ω with increase in pyrrole concentration within 0.2 mg/ml until the concentration reached a value of about 0.4 mg/ml, above which the rate of decrease diminished. The effect of initial treatment with monomer or oxidant prior to polymerisation reaction with regards to thickness and surface resistance was minimal. The immersion time of the textile into the monomer solution prior to polymerisation reaction did not have a significant effect on the abrasion resistance.

A comparison of pilling results tested with the ICI pill box and a new perspex™ pill box

Identical single jersey wool knit fabrics produced inconsistent results when tested on the same type of ICI pill box in 4 independence testing laboratories.  The hypothesis formulated to investigate this event was that continued pilling testing in the ICI pill box changes the frictional properties of the cork liners, resulting in the difference pilling ratings.  The aim of this study was to decrease the inconsistencies in the pilling results by replacing the conventional cork lined pill box with a Perspex^TM pill box.  The smae or similar pilling results found for several of the knit facots tested in the two difference pill boxes, while for others there were some significant differences found.  In addition, while using the Perspex^TM pill box observations of the movement of the pilling tubes during testing provided evidence of greater fabric-to-fabric abrasion, rather the expected high degree of fabric-to-cork abrasion (or fabric-to-Perspex^TM) during pilling testing.

Improvement of adhesion of conductive polypyrrole coating on wool and polyester fabrics using atmospheric plasma treatment

In this paper wool and polyester fabrics were pretreated with atmospheric plasma glow discharge (APGD) to improve the ability of the substrate to bond with anthraquinone-2-sulfonic acid doped conducting polypyrrole coating. A range of APGD gas mixtures and treatment times were investigated. APGD treated fabrics were tested for surface contact angle, wettability and surface energy change. Effect of the plasma treatment on the binding strength was analyzed by studying abrasion resistance, surface resistivity and reflectance. Investigations showed that treated fabrics exhibited better hydrophilicity and increased surface energy. Surface treatment by an APGD gas mixture of 95% helium/5% nitrogen yielded the best results with respect to coating uniformity, abrasion resistance and conductivity.

東澳大利亞悉尼盆地南部二疊紀的地層、沈積環境與盆地演化

The latest Carboniferous to Triassic Sydney-Gunnedah-Bowen Basin System in the eastern Australia is an elongate structural basin that locates between the Lachlan Caledonian Fold Belt in the west and the New England Fold Belt in the east. Extending from the Gunnedah district in the north to the Batemans Bay in the south, the Sydney Basin is a subbasin located in the southern part of the Sydney-Gunnedah-Bowen Basin System. The Permian in Sydney Basin consists of sedimentary sequences of fluvial, delta, littoral and shallow marine environments, as well as volcanic rocks. In the southwest of southern Sydney Basin, the Permian unconformably onlaps the highly deformed and metamorphosed Lachlan Fold Belts. The Permian System from the southern Sydney Basin comprises the Lower Permian Tallaterang Group (consisting of Clyde Coal Measures and Wasp Head Formation), Shoalhaven Group ( consisting of the Lower Permian Yadboro & Tallong Conglomerate, Yarrunga Coal Measures, Pebbly Beach Formation, Snapper Point Formation and the Middle Permian Wandrawandian Siltstone, Nowra Sandstone, Berry Siltstone and Broughton Formation) and the Upper Permian Illwarra Coal Measures. From the latest Carboniferous to the Middle Triassic, the SydneyBowen Basin had experienced different tectonic phases from a back-arc extensional regime to a typical foreland basin: a back-arc extensional phase, a passive thermal sag phase and a flexural loading and increased compressional phase.

A comparative study of the mechanical properties of wool and alpaca fibres

This study reports the latest research into alpaca and wool fibres. In particular, those properties that have received little attention in research literature have been examined. They include single fibre abrasion and bending fatigue, single fibre tensile properties, as well as resistance to compression behaviour. These properties are important because they affect the softness and pilling propensity of these fibres and the resultant fabrics. Clean wool and alpaca fibres were used in this study. Fibre abrasion/bending fatigue measurements were carried out using a Textechno FIBRESTRESS instrument. The resistance to compression (RtC) tests were carried out according to Australian Standard AS3535-1988. The results indicate that wool and alpaca fibres behave quite differently, even though both fibre types are of animal origin. Wool fibre resistance to compression decreases as fibre diameter increases while the opposite appears to occur for alpaca fibres. For both wool and alpaca the number of abrasion/bending cycles at fibre break increases with an increase in fibre diameter, it takes longer to break the alpaca fibres. Reasons for these differences have been postulated based on differences in fibre surface and structure between alpaca and wool.

Photochromic wool fabrics with enhanced durability and photochromic performance

In our previous work, we have produced a photochromic wool fabric by applying a thin layer of hybrid silica-photochromic dye onto the wool surface. The coating showed a very fast optical response, but had little influence on the fabric handle, however durability was low. In this context, we reported that durability of the hybrid layer can be improved by introducing epoxy groups into the silica matrix via co-hydrolysis and co-condensation of an alkyl trialkoxysilane (ATAS) and 3-glycidoxypropyltrimethoxysilane (GPTMS). The presence of epoxy groups in the silica enhanced both washing and abrasion durabilities. Also, the optical response speed was slightly increased as well. Effects of the type of alkyl silane and the GPTMS:alkyl silane ratio on the coating durability, fabric handle and optical response were examined.

Fibre coating composition

An abrasion-resistant, electrically conductive material comprising a natural fibre-containing substrate and an electrically conductive conjugated polymer coating thereon is disclosed. A process for preparing an abrasion-resistant, electrically conductive material is also disclosed. The process comprises providing at least one monomer capable of forming an electrically conductive conjugated polymer, and a suitable substrate having a substrate surface, subjecting the substrate surface to a surface treatment step to improve abrasion resistance, and exposing the substrate surface to a vapour of the monomer to form an electrically conductive conjugated polymer coating thereon.