Interaction between the coating characteristics of galvanneal steel and forming parameters during flat die drawing

Galvanneal steel is considered to be better for automotive applications than its counterpart, galvanized steel, mainly because of its superior coating and surface properties. Galvanneal steel is produced by hot dipping sheet steel in a bath of molten zinc with small, controlled, levels of aluminium, followed by annealing which creates a Fe-Zn intermetallic layer. This intermetallic layer of the coating improves spot weldability and improves subsequent paint appearance. However, if the microstructure of the coating is not properly controlled and forming parameters are not properly selected, wear of the coating could occur during stamping. Frictional sliding of the sheet between the tool surfaces results in considerable amount of coating loss. An Interstitial Free steel with a Galvanneal coating of nominally 60g/m2 was used for the laboratory experiments. Flat Face Friction (FFF) tests were performed with different forming conditions and lubricants to simulate the frictional sliding in stamping. Glow-Discharge Optical Emission Spectrometry (DG-OES) was used to measure the change in the coating thickness during sliding. Optical microscopy was considered for imaging the surfaces as well as an optical method to compare the changes in the coating thickness during the forming. The change to the Galvanneal coating thickness was found to be a function of forming parameters.

Photocatalytic decolorization of lanasol blue CE dye solution using a flat-plate reactor

This paper reports the effectiveness of the photocatalysis TiO₂ in degrading Lanasol Blue CE. A flat-plate reactor (FPR) with a reactor area of 0.37 m² and ultraviolet (UV) light source of six 36 W blacklight lamps was used in the study. Operating variables including dosage of the photocatalyst, flow rates through the FPR, UV intensity, and tilted angle of the reactor were investigated to degrade Lanasol Blue CE. Results showed that the photocatalytic process can efficiently remove the color in textile dyeing effluent. The degradation process was approximated using first-order kinetics. The photocatalytic apparent reaction rate increased with the increasing UV intensity received by the photocatalyst TiO₂ in slurry. The liquid flow rate and tilted angle influenced the film thickness. The apparent reaction rate constant was mainly determined by the liquid film thickness, UV intensity, and the dosage of the photocatalyst. The findings of this research can be utilized as preliminary input for potential solar photocatalytic applications on color removal from dye solutions.

Photocatalytic degradation of dyes in wastewater using TiO2/UV in a flat-plate reactor

The photocatalyst TiO₂ with UV irradiation was used to degrade dyes in textile effluent in a flat-plate photoreactor. A test system was built with the reactor area of 1 x 0.3m2, UV light of six 36W-blacklight. TiO₂ powder P25 with BET surface area 50±15m2/g, average primary particle size 21 nm, purity> 99.5% and content of 83.9% anatase and 16.1 % rutile was used as the photocatalyst. A number of dyes commonly present in dyeing wastewater were tested in this study. The different operating parameters, such as dosage of photocatalyst, the structure of the reactor, flow rates through the flat-plate reactor, UV radiation intensity and tilted angle of the reactor, were investigated. The results showed that the photocatalytic process could efficiently remove most of the colour contained in the dyeing wastewater. It was experimentally observed that first-order kinetics was adequate for characterising the process. The flow rate and the tilted angle had some influence on the film thickness of the fluid in the reactor and the empirical correlation between the film thickness of the fluid and these two parameters was developed. The photoreaction rate was mainly determined by the film thickness of the fluid on the reactor surface and the dosage of the photocatalyst. Optimum operating parameters of the system were found to be at the film thickness of about 1.4mm and a TiO₂ dosage of 1 gIL. The higher the UV intensity, the faster the reaction rate was. The results of these experiments showed that this method has the great potential for colour removal from wastewater at commercial scale.

To overcome the common difficulty of separating the used TiO₂ suspension after treatment precipitation followed with filtration was used in this study to determine the separation efficiencies. On the other hand, TiO₂ in a small pillar shape was also studied for photocatalytic degradation of textile dye effluent. The pillar pellet was made in Oegussa Company, Germany ranging from 2.5 to 5.3mm long and with a diameter of 3.7mm. It was almost pure TiO₂ (83.2% anatase and 16.8% rutile), with a S-content of <20 ppm and a CI content of the order of 0.1 wt. %. No further elements are present in contents above 0.05 wt.%. The TiO₂ pillars were placed on the flat-plate reactor that was divided by the rectangular slots and irradiated under UV light when the treated solution went through the reactor. Four dyes and their mixtures were tested. The results showed that the photocatalytic process under this configuration efficiently remove the colour from textile dyeing effluent, and pillar shape TiO₂ photocatalyst was not dissolved in water and very easy to be separated from solution, enabling it to be reused many times. The first-order kinetics was adequate for characterising the photocatalytic degradation process and the photocatalytic performance was comparable to TiO₂ powder. It is believed that the TiO₂ pellet would be a preferable form of photocatalyst in applications for textile effluent treatment process, and other wastewater treatment processes.

Solar photocatalytic oxidation (PCO) process with a flat-plate reactor

An experimental rig with a flat-plate solar reactor was built to study the effectiveness of degradation using the reactive methylene blue as sensitive objective. The factors that affect the degradation performance, such as dosages of photocatalyst (Ti0₂), initial concentration of reactive methylene blue, flow rate through the flat-plate reactor, solar UV radiation intensity and decolourising efficiency of the solution, have been investigated. The results showed that the solar PCO process with a Flat-plate Reactor could degrade the methylene blue and decolour in methylene blue solution efficiently.

So flat, so cute! Robots, superflatness and asian architectural futures

Many depictions of urban futures have a distinctly Asian flavour. There have been numerous visions of highly technological futures whose environments extrapolate present societies into futures technically, culturally and politically dominated by China or Japan, Such futures are portrayed as both exciting and threatening, to the point that the Japanese academic and cultural critic Toshiya Ueno used the term ‘Techno-Orientalism’ to describe the phenomenon. Nevertheless, whether Western interest is Orientalist or not, Asian architects are also increasingly looking to their own contemporary and future cultures for inspiration. This paper will discuss two manifestations of this. The first is Thai architect Sumet Jumsai’s Bank of Asia. Unlike contemporaneous English hightech buildings, with their coldly mechanistic representation of ducts and struts, Jumsai’s Bank of Asia, takes on the anthropomorphic character of Japanese scifi robots. It is endearing, friendly, even cute. The second example is what might be termed superflat architecture, from the term coined by the artist Takashi Murakami to describe an aesthetic of intrinsic flatness, eliminating depth in favour of skin and surface. The emergence of Techno-Cute and Superflat architecture suggest contemporary Asian architectural sensibilities that neither derive their aesthetic qualities solely from tradition nor from Western Modernism or Postmodernism.

Differential calcineurin signalling activity and regeneration efficacy in diaphragm and limb muscles of dystrophic mdx mice

Calcineurin activity is essential for successful skeletal muscle regeneration in young mdx mice and in wild type mice following myotoxic injury and cryodamage. In mature myofibres of adult mdx mice, calcineurin stimulation can ameliorate the dystrophic pathology. The aim of this study was to test the hypothesis that the more severe dystrophic pathology of the diaphragm compared with hindlimb muscles of mdx mice could be attributed to aberrant calcineurin signalling and that due to ongoing regeneration calcineurin activity would be greater in muscles of adult mdx than wild type mice. Differences in markers of regeneration between tibialis anterior and diaphragm muscles were also characterised, to determine whether there was an association between regeneration efficacy and calcineurin activity in dystrophic muscles. In diaphragm muscles of adult mdx mice, the proportion of centrally nucleated fibres and developmental myosin heavy chain protein expression was lower and myogenin protein expression was higher than in tibialis anterior muscles. Calcineurin and activated NFATc1 protein content and calcineurin phosphatase activity were higher in muscles from mdx than wild type mice and calcineurin activation was greater in diaphragm than tibialis anterior muscles of mdx mice. Thus, despite greater calcineurin activity in diaphragm compared to hindlimb muscles, regeneration events downstream of myoblast differentiation and mediated by the injured myofibre were severely compromised.

Pre- and post-natal development of the diaphragm

Animal models were used to examine properies of the diaphragm (the main respiratory muscle) before and after birth. The study revealed an insufficient blood supply to the fetus can result in structural and functional damage to the diaphragm. Damage was prevented when the mother was supplemented with creatine during pregnancy.

Comparing experiments of the stressed skin diaphragm spanning several and few purlins

Concerning the specialty of the testing of stressed skin diaphragm assembly, the current loading method of cantilever beam test is improved by the diagonally loading method. In order to investigate the differences of the shear behavior between the stressed skins spanning several purlins and few purlins , which have the same forms and spaces of the connections and purlins, comparing experiments are carried out. Using the curve fitting method, the test results are quantified. The shear rigidity of two specimens is gained. It shows that the shear rigidity of the diaphragm spanning several purlins is quite higher than that spanning few purlins, but the carrying capacity of the former is a little lower than that of the latter.

Field test study on the shear behaviour of stressed skin diaphragm spanning several purlins

Although profiled steel sheets have the diaphragm effect in steel structure, since there is no specific code to follow in China, it is only used as the reservation of the structural stiffness.So it results in economic wastes.In order to investigate the contribution of stressed skin to the overall stiffness, field tests are carried out to measure the lateral stiffness of the frames with and without stressed skin diaphgram.Based on the superposition principle and using the curve fitting method, the test results are quantified.The shear rigidity of stressed skin diaphgram spanning several purlins is gained indirectly.It shows that the shear rigidity of the diaphragm between two frames is even close to the lateral stiffness of one frame.

Repeatable sediment associations of burrowing bivalves across six European tidal flat systems

Burrowing bivalves are associated with particular sediment types within sedimentary systems. The degree to which bivalve sediment associations are repeatable across systems has seldom been investigated. To investigate whether such repeatability exists across tidal flats, we compared adult and juvenile distributions of 3 bivalve species (Cerastoderma edule, Scrobicularia plana, Macoma balthica) across 6 European tidal flats. Across systems, the adult bivalves showed fairly repeatable distributions, with C. edule occurring in sandy sediments and M. balthica and S. plana occurring in muddy sediments. Exceptions were observed in systems composed primarily of muddy sediments (Aiguillon Bay and Marennes-Oléron Bay) and the Dutch Wadden Sea. Interestingly, juveniles and adults of C. edule and S. plana showed similar distributions across systems. M. balthica juveniles and adults showed habitat separation in 3 of the 6 studied systems; in 2 of these, it has been shown previously that juvenile M. balthica settle in mud at high tidal levels and migrate to lower sandier flats later in life. The high occurrence of juvenile M. balthica towards high sandy flats in Mont Saint-Michel Bay suggests that juveniles might choose high tidal flats rather than muddy sediments per se. A repeatable association in adults and juveniles with respect to sediment could suggest that juveniles actively settle in the proximity of the adults and/or that juveniles settling away from the adults incur a higher mortality due to either predation, physiological stress, or other factors.

The influence of surface forces on thin film drainage between a fluid drop and a flat solid

An experiment is described in which a mica surface is driven towards a mercury drop immersed in aqueous electrolyte. Under appropriate conditions, hydrodynamic pressure in the aqueous film creates a classical dimple in the mercury drop. The use of optical interferometry and video recording to monitor the shape of the drop and the thickness of the aqueous film with sub-nanometre resolution yields a high density of precise data showing the formation and evolution of the dimple as the film drains. Variation of electrical potential applied to the mercury phase allows control of the surface forces acting between the drop and the mica surface, so that the effect of surface forces on the film drainage process is highlighted. It is found that the film thickness at the centre of the dimple and the lateral extent of the dimple are not significantly affected by surface forces. On the other hand, the minimum film thickness at the edge of the dimple is sensitive even to weak surface forces. Since this minimum film thickness is a major determinant of the film drainage rate, it is shown that surface forces have an important effect on the overall drainage process.

How honeybees make grazing landings on flat surfaces

Freely flying bees were filmed as they landed on a flat, horizontal surface, to investigate the underlying visuomotor control strategies. The results reveal that (1) landing bees approach the surface at a relatively shallow descent angle; (2) they tend to hold the angular velocity of the image of the surface constant as they approach it; and (3) the instantaneous speed of descent is proportional to the instantaneous forward speed. These characteristics reflect a surprisingly simple and effective strategy for achieving a smooth landing, by which the forward and descent speeds are automatically reduced as the surface is approached and are both close to zero at touchdown. No explicit knowledge of flight speed or height above the ground is necessary. A model of the control scheme is developed and its predictions are verified. It is also shown that, during landing, the bee decelerates continuously and in such a way as to keep the projected time to touchdown constant as the surface is approached. The feasibility of this landing strategy is demonstrated by implementation in a robotic gantry equipped with vision.