Optical microsensor for counting food substance particles in lab-on-a-chips

Integrated optical detection is considered to be an important operation in lab-on-a-chips. This paper presents an optical fiber-based micro-sensor that is capable of detecting food substance particles in a lab-on-a-chip. The system consists of a microcontroller and associated circuitry, a laser emitter, a laser receiver, fiber optic cables, a microfluidics chip, and the food substance samples to be tested. When the particles flow through the microfluidic channel in the chip, the receiver’s output voltage varies due to the particles blocking the passage of the laser ray. The changes in the collected signals are analyzed to count the number of particles. Experiments are conducted on several food substance samples including talcum powder, ground ginger, and soy sauce. The experimental results are presented and discussed.

An autonomous trimming system of large glass fiber reinforced plastics parts using an omni-directional mobile robot and its control

This paper describes an automated trimming system of large glass fiber reinforced plastic (GFRP) using an omni-directional wheeled mobile robot (WMR) and its path control method. In trimming GFRP parts, much glass fiber and plastic powder dust occur and it becomes bad visible in environment. It is necessary to correct dead-reckoning errors of the WMR in order to control its moving path. We have discussed an external correction method of the dead-reckoning errors for the WMR using ultrasonic sensor.

Gaze behavior among experts and trainees during optic disc examination : does how we look affect what we see?

Purpose. The authors compared the visual gaze behaviors of glaucoma subspecialists with those of ophthalmology trainees during optic disc and retinal nerve fiber layer (RNFL) examination.

Methods. Seven glaucoma subspecialists and 23 ophthalmology trainees participated in the project. Participants were shown eight glaucomatous optic disc images with varied morphology. Eye movements during examination of the optic disc photographs were tracked. For each disc image, graders were asked to assign a presumptive diagnosis for probability of glaucoma. There was no time restriction.

Results. Overall, trainees spent more time looking at disc images than glaucoma subspecialists (21.3 [13.9–37.7] vs. 16.6 [12.7–19.7]) seconds; median [interquartile range (IQR)], respectively; P < 0.01) and had no systematic patterns of gaze behavior, and gaze behavior was unaltered by disc morphology or topographic cues of pathology. Experienced viewers demonstrated more systematic and ordered gaze behavior patterns and spent longer times observing areas with the greatest likelihood of pathology (superior and inferior poles of the optic nerve head and adjacent RNFL) compared with the trainees. For discs with focal pathology, the proportion of total time spent examining definite areas of pathology was 28.9% (22.4%–33.6%) for glaucoma subspecialists and 13.5% (12.2%–19.2%) for trainees (median [IQR]; P < 0.05). Furthermore, experts adapted their viewing habits according to disc morphology.

Conclusions. Glaucoma subspecialists adopt systematic gaze behavior when examining the optic nerve and RNFL, whereas trainees do not. It remains to be elucidated whether incorporating systematic viewing behavior of the optic disc and RNFL into teaching programs for trainees may expedite their acquisition of accurate and efficient glaucoma diagnosis skills.

Reflectance response of tapered optical fiber coated with graphene oxide nanostructured thin film for aqueous ethanol sensing

In this work, optical sensing performance of tapered multimode fiber tip coated with graphene oxide (GO) nanostructured thin film towards aqueous ethanol with different concentrations is investigated. The tapering process of the optical fiber is done by a glass processing machine. The multimode optical fiber tip is dip-coated with GO and annealed at 70 °C to enhance the binding of the nanomaterials to the silica fiber. FESEM, Raman microscopy and XRD analyses are performed to micro-characterize the GO thin films. The morphology of the GO is observed to be in sheets forms. The reflectance response of the GO coated fiber tip is compared with the uncoated tip. The measurements are taken using a spectrophotometer in the optical wavelength range of 550-720 nm. The reflectance response of the GO coated fiber tip reduced proportionally, upon exposure to ethanol with concentration range of 5-80%. The dynamic response of the developed sensor showed strong reversibility and repeatability when it is exposed to ethanol with concentrations of 5%, 20% and 40% in distilled water. At room temperature, the sensor shows fast response and recovery as low as 19 and 25 s, respectively. © 2014 Elsevier B.V.

Knitted strain sensor textiles of highly conductive all-polymeric fibers

A scaled-up fiber wet-spinning production of electrically conductive and highly stretchable PU/PEDOT:PSS fibers is demonstrated for the first time. The PU/PEDOT:PSS fibers possess the mechanical properties appropriate for knitting various textile structures. The knitted textiles exhibit strain sensing properties that were dependent upon the number of PU/PEDOT:PSS fibers used in knitting. The knitted textiles show sensitivity (as measured by the gauge factor) that increases with the number of PU/PEDOT:PSS fibers deployed. A highly stable sensor response was observed when four PU/PEDOT:PSS fibers were co-knitted with a commercial Spandex yarn. The knitted textile sensor can distinguish different magnitudes of applied strain with cyclically repeatable sensor responses at applied strains of up to 160%. When used in conjunction with a commercial wireless transmitter, the knitted textile responded well to the magnitude of bending deformations, demonstrating potential for remote strain sensing applications. The feasibility of an all-polymeric knitted textile wearable strain sensor was demonstrated in a knee sleeve prototype with application in personal training and rehabilitation following injury.

Securing sensor networks by moderating frequencies

Security of Wireless Sensor Network (WSN) is a key issue in information security. Most existing security protocols exploit various Mathematical tools to strengthen their security. Some protocols use the details of the geographical location of the nodes. However, to the best authors’ knowledge, none of the existing works exploit the constraints faced by the adversary, specifically, tracing a particular frequency from a large range of unknown frequency channels. The current work uses positional details of the individual nodes. Then the aim is to exploit this weakness of tracing frequencies by assigning a wide range of frequency channels to each node. Experiments using Magneto Optic Sensors reveal that any change of the parametric Faraday’s rotational angle affects the frequency of the Optical waves. This idea can perhaps be generalized for practically deployable sensors (having respective parameters) along with a suitable key management scheme.

Polypyrrole-coated PDMS fibrous membrane: flexible strain sensor with distinctive resistance responses at different strain ranges

Flexible sensors capable of detecting large strain are very useful for health monitoring and sport applications. Here a strain sensor is prepared by applying a thin layer of conducting polymer, polypyrrole (PPy), onto the fiber surface of an elastic fibrous membrane, electrospun polydimethylsiloxane (PDMS). The sensor shows a normal monotonic resistance response to strain in the range of 0–50%, but the response becomes “on-off switching” mode when the strain is between 100 and 200%. Both response modes are reversible and can work repeatedly for many cycles. This unique sensing behavior is attributed to overstretching of the polypyrrole coating, unique fibrous structure, and elasticity of PDMS fibers. It may be useful for monitoring the states where motions are only allowed in a particular range such as joint rehabilitation.