Construction of extrusion limit diagram for AZ31 magnesium alloy by FE simulation

The maximum speed at which magnesium can be extruded is considerably slower than that of many common aluminium extrusion alloys. This affects both the economies of production and the final mechanical behaviour. The present work quantifies the limiting extrusion speeds and ratios of magnesium alloy AZ31 as a function of billet temperature. This is done by combining hot compression test results, FE simulations and extrusion trials. Hot working stress–strain curves displayed a distinct dynamic recrystallisation peak. These data were used as a “look-up” table for the FE simulations in which the cracking limit was assumed to occur when the surface temperature reaches the incipient melting point. The maximum extrusion ratio predicted using FE analysis dropped from 90 to 40 when the extrusion ram speed was raised from 5 to 50 mm/s. The predicted limits agree well with the occurrence of cracking in both a laboratory and a commercial extrusion trial.

A community based systems diagram of obesity causes

INTRODUCTION: Application of system thinking to the development, implementation and evaluation of childhood obesity prevention efforts represents the cutting edge of community-based prevention. We report on an approach to developing a system oriented community perspective on the causes of obesity. METHODS: Group model building sessions were conducted in a rural Australian community to address increasing childhood obesity. Stakeholders (n = 12) built a community model that progressed from connection circles to causal loop diagrams using scripts from the system dynamics literature. Participants began this work in identifying change over time in causes and effects of childhood obesity within their community. The initial causal loop diagram was then reviewed and elaborated by 50 community leaders over a full day session. RESULTS: The process created a causal loop diagram representing community perceptions of determinants and causes of obesity. The causal loop diagram can be broken down into four separate domains; social influences; fast food and junk food; participation in sport; and general physical activity. DISCUSSION: This causal loop diagram can provide the basis for community led planning of a prevention response that engages with multiple levels of existing settings and systems.

An extension of the flower pattern diagram for roll forming

The initial process design of a roll forming system is often based on the traditional ‘flower pattern diagram’. In this diagram, the cross sections of the strip at each roll stand are superimposed on a single plane; the diagram is a 2D representation of the 3D process. In the present work, the flower pattern is extended into three dimensions. To demonstrate the method, the forming path or trajectory of a point at the edge of the strip during forming a V-section is considered. The forming path is a surface curve that lies on a cylindrical surface having its axis along the machine axis. This surface is unwrapped to give its plane development and important features of the forming process can be determined and are readily interpreted from this plane curve. It is shown that at any stage in the process, the axial strain and the curvature of the sheet adjacent to the point are dependent on the slope of the trajectory in this plane projection. This new diagram, which apparently has not been used previously, provides a useful initial method of examining the roll forming process and optimising the flower pattern. The model is purely geometric, as is the original flower pattern approach, and does not include the effect of material behaviour. The concept is applied to several cases available in the literature. It shows that the lowest level of shape defect in the part is achieved when the trajectory of the strip edge follows the shortest line length between the start and finish of forming, leading to the least longitudinal strain introduced in the flange. This trend is in agreement with previous experimental observations, suggesting that the analytical model proposed may be applied for early process design and optimisation before time-consuming numerical analysis is performed.

Drawing process : what's a diagram?

Within the architectural universe there have been numerous attempts in recent years to define the term diagram. Etymologically, it means exclusively “through graphic representation”, which does not clarify much (from the Greek, dia, through + gramma, graphic representation). Jennifer Sigler defines it as the minimum graphic element that explains a concept. Federico Soriano borrows from Federico García Lorca, and claims that diagrams are the marrow of form or content. Efforts to clarify the nature of these powerful graphical representations have multiplied at a similar rate as its ever-increasing use in contemporary architectural projects.

Enhancing flexible business training: learners and enterprises

Focuses on flexible training and its implementation in the workplace; examines the barriers for those learners on vocational programmes involved in self-directed independent learning. Discusses ways to develop learners self-direction and to improve learners ability to use and access a wide range of learning media. Highlights the need to establish structures to support learning through flexible training. Puts forward a two-dimensional diagram describing business vocational learner preferences, and outlines three sets of strategies to develop effective enterprise support for flexible training.

Elastic bending of steel-polymer-steel (SPS) laminates to a constant curvature

The shear strain of the interlayer in the elastic regime for a Steel-Polymer-Steel (SPS) laminate material has been studied during bending to a constant curvature. An analytical model is developed and the influence of process parameters are analyzed. The tension in the cover sheets is also determined and, finally, a moment diagram is calculated. The results show that the moment in the SPS laminate is nonuniform along the bent strip even though the curvature is constant because of the tension and compression forces introduced in the cover sheets by the shear reaction force of the interlayer material.

Should we save or should we consume? Linking growth theories and the Keynesian models

In major economic growth theories, high saving rate gives rise to high level of output per capita. But in Keynesian economics, high saving rate causes low consumption and will lead the economy into recession. Students may ask, "For the well-being of an economy, should we save or should we consume?" In most of the intermediate macroeconomics textbooks, economic growth and Keynesian economics are taught in separate chapters; and in many cases, these chapters are not even successive to each other. There lacks a continuity between the long run and short run models. This paper builds a bridge between growth theories and Keynesian models. It links the Solow diagram and the IS-LM curves and depicts the short run and long run implications of a change in the saving rate.

To save or to consume: linking growth theory with the Keynesian model

In the neoclassical growth theory, higher saving rate gives rise to higher output per capita. However, in the Keynesian model, higher saving rate causes lower consumption, which may lead to a recession. Students may ask, “Should we save or should we consume?” In most of the macroeconomics textbooks, economic growth and Keynesian economics are in separate, sometimes unsequential, chapters. The connection between the short run and the long run is not apparent. The author builds a bridge between the neoclassical growth theory and the Keynesian model. He links the Solow diagram and the IS-LM curves and depicts the short-run to long-run transition of the economy after changes in saving and other macroeconomic policies.

Determination of lower-bound ductility for AZ31 magnesium alloy by use of the bulge specimens

Despite the high demand for industrial applications of magnesium, the forming technology for wrought magnesium alloys is not fully developed due to the limited ductility and high sensitivity to the processing parameters. The processing window for magnesium alloys could be significantly widened if the lower-bound ductility (LBD) for a range of stresses, temperature, and strain rates was known. LBD is the critical strain at the moment of fracture as a function of stress state and temperature. Measurements of LBD are normally performed by testing in a hyperbaric chamber, which is highly specialized, complex, and rare equipment. In this paper an alternative approach to determine LBD is demonstrated using wrought magnesium alloy AZ31 as an example. A series of compression tests of bulge specimens combined with finite element simulation of the tests were performed. The LBD diagram was then deduced by backward calculation.

The influence of temperature on the forming behavior of metal/polymer laminates in sheet metal forming

The influence of temperature on the forming behavior of an aluminum/polypropylene/aluminum (APA) sandwich sheet was studied. Shear and tensile tests were performed to determine the mechanical properties of the laminate and the component materials as a function of process temperature. The forming limit diagram (FLD) of the laminate was established for two different temperatures, and its springback behavior was examined in four-point bend and channel bend tests. Cup forming tests were performed at various test temperatures to determine the limiting drawing ratio (LDR) and the tendency for wrinkling at these temperatures. Although there was only a minor influence of temperature on the mechanical properties and the FLD values of the laminate, the bend test results reveal that springback can be reduced by forming at higher temperature. The decreasing strength of the core material with rising process temperature led to an increased tendency of the laminate to wrinkle in the heated cup drawing tests.

Checks and cheques : implementing a population health and recall system to improve coverage of patients with diabetes in a rural general practice

Identification of all diabetic patients in the population is essential if diabetic care is to be effective in achieving the targets of the St Vincent Declaration.¹ The challenge therefore is to establish population based monitoring and control systems by means of state of the art technology in order to achieve quality assurance in the provision of care for patients with diabetes. ^2,3 Disease management receives extensive international support as the most appropriate approach to organising and delivering healthcare for chronic conditions like diabetes.⁴ This approach is achieved through a combination of guidelines for practice, patient education, consultations and follow up using a planned team approach and a strong focus on continuous quality improvement using information technology. ^5,6 The current software (Medical Director) could not easily meet these requirements which led us to adopt a trial of Ferret. In designing this project we used change management⁷ and the plan, do, study, act cycle⁸ illustrated in Diagram 1.

Chemical modification of timber decking : assessing the parameters of acceptability

The criteria for accepting or rejecting a technology extend beyond the intrinsic properties of the finished product such as physical performance. There are also extrinsic factors such as the history of the product and trust in the manufacturers and suppliers, as well as the perceptions and risk management strategies of various stakeholder groups. A methodology was trialled to take into account the extended supply chain of the product, while simultaneously engaging stakeholders to determine and to understand their perceptual frameworks. Three pine decking products manufactured using different amounts and types of chemical modification were compared using life cycle assessment and the comments of 114 respondents from six stakeholder groups in New Zealand. The results of the perceptual research include a quadrant diagram which allows a visual comparison of the responses of different stakeholders to actual or hypothetical products, aiding the identification of when and why certain technologies may be disqualified from acceptability or become the topic of public debate.