A new approach for wind and solar type DG placement in power distribution networks to enhance systems stability

This paper proposes a distributed generator (DG) placement methodology based on newly defined term reactive power loadability. The effectiveness of the proposed planning is carried out over a distribution test system representative of the Kumamoto area in Japan. Firstly, this paper provides simulation results showing the sensitivity of the location of renewable energy based DG on voltage profile and stability of the system. Then, a suitable location is identified for two principal types DG, i. e., wind and solar, separately to enhance the stability margin of the system. The analysis shows that the proposed approach can reduce the power loss of the system, which in turn, reduces the size of compensating devices.

Design of a norm-bounded LQG controller for power distribution networks with distributed generation

This paper presents a novel excitation control design to improve the voltage profile of power distribution networks with distributed generation and induction motor loads. The system is linearised by perturbation technique. Controller is designed using the linear-quadratic-Gaussian (LQG) controller synthesis method. The LQG controller is addressed with norm-bounded uncertainty. The approach considered in this paper is to find the smallest upper bound on the H∞ norm of the uncertain system and to design an optimal controller based on this bound. The design method requires the solution of a linear matrix inequality. The performance of the controller is tested on a benchmark power distribution system. Simulation results show that the proposed controller provides impressive oscillation damping compared to the conventional excitation controller.

Effects of load modeling in power distribution system with distributed wind generation

This paper presents the impact of different types of load models in distribution network with distributed wind generation. The analysis is carried out for a test distribution system representative of the Kumamoto area in Japan. Firstly, this paper provides static analysis showing the impact of static load on distribution system. Then, it investigates the effects of static as well as composite load based on the load composition of IEEE task force report [1] through an accurate time-domain analysis. The analysis shows that modeling of loads has a significant impact on the voltage dynamics of the distribution system with distributed generation.

Voltage oscillations in power distribution networks in the presence of DFIGs and induction motor loads

This paper investigates the oscillatory behavior of power distribution systems in the presence of distributed generation. The analysis is carried out over a distribution test system with two doubly fed induction type wind generators and different types of induction motor loads. The system is linearized by the perturbation method. Eigenvalues are calculated to see the modal interaction within the system. The study indicates that interactions between closely placed converter controllers and induction motor loads significantly influence the damping of the oscillatory modes of the system. The critical modes have a frequency of oscillation between the electromechanical and subsynchronous oscillations of power systems. Time-domain simulations are carried out to verify the validity of the modal analysis and to provide a physical feel for the types of oscillations that occur in distribution systems. Finally, significant parameters of the system that affect the damping and frequency of the oscillation are identified.

Agent-based reactive power management of power distribution networks with distributed energy generation

In this paper, a new agent-based distributed reactive power management scheme is proposed to improve the voltage stability of energy distribution systems with distributed generation units. Three types of agents – distribution system agent, estimator agent, and control agent are developed within the multi-agent framework. The agents simultaneously coordinated their activities through the online information and energy flow. The overall achievement of the proposed scheme depends on the coordination between two tasks – (i) estimation of reactive power using voltage variation formula and (ii) necessary control actions to provide the estimated reactive power to the distribution networks through the distributed static synchronous compensators. A linear quadratic regulator with a proportional integrator is designed for the control agent in order to control the reactive component of the current and the DC voltage of the compensators. The performance of the proposed scheme is tested on a 10-bus power distribution network under various scenarios. The effectiveness is validated by comparing the proposed approach to the conventional proportional integral control approach. It is found that, the agent-based scheme provides excellent robust performance under various operating conditions of the power distribution network.

Distribution of power requirements during yarn winding in ring spinning

A model of a yam package is established for a ring spinning system. The yarn layer, surface area, and mass of the yam package are formulated with respect to the diameters of the empty bobbin and full yarn package, yarn count, and yarn winding-on time. Based on the principles of dynamics and aerodynamics, models of the power requirements for overcoming the skin friction drag, increasing the kinetic energy of the yarn package (bobbin and wound yarn), and overcoming the yarn wind-on tension are developed. The skin friction coefficient on the surface of a rotating yam package is obtained from experiment. The power distribution during yam packaging is discussed based on a case study. The results indicate that overcoming the skin friction drag during yarn winding consumes the largest amount of energy. The energy required to overcome the yarn wind-on tension is also significant.

Power quality impacts in a typical microgrid

Microgrid (MG) power system plays an important role to fulfill reliable and secure energy supply to critical loads of communities as well as for communities in remote area. Distributed Generation (DG) sources integrated in a MG provides numerous benefits, at the same time leads to power quality issues in the MG power distribution network. Power Quality (PQ) issue arises due to the integration of an intermittent nature of Renewable Energy (RE) sources with advanced Power Electronics (PE) converter technology. Also, presence of non-linear and unbalancing loads in MG seems to affect PQ of the energy supply in power distribution network. In this paper, PQ impacts like; power variation, voltage variation, Total Harmonic Distortion (THD), and Unbalance voltage level have been analysed in Low Voltage (LV) distribution network of typical MG power system model. In this study, development of MG model and PQ impact analysis through simulation has been done in PSS-Sincal software environment. Analysis results from the study can be used as a guideline for developing a real and independent MG power system with improved PQ conditions.

Power quality analysis in microgrid: an experimental approach

Microgrid (MG) integrated with Distributed Generation (DG) provides several benefits like reliable, secure, and high efficient of energy supply, while minimizing power loss, deferring expansion of power distribution infrastructures, and reduced carbon emission of energy supply etc. to the communities. Despite of the several benefits, there are several challenges existing due to the integration of different characteristics and technology of DG sources in MG network. Power Quality (PQ) issue is one of the main technical challenges in MG power system. In order to provide improved PQ of energy supply, it is necessary to analyse and quantify the PQ level in MG network. This paper investigates the detail of PQ impacts in a real MG network carried out through an experimental analysis. Voltage and frequency variations/deviations are analysed in both on-grid and off-grid mode of MG operation at varying generation and varying load conditions. Similarly un-balance voltage and current level in neutral are estimated at unbalanced PV generation and uneven load distribution in MG network. Also current and voltage THD are estimated at different PV power level. Finally the results obtained from the analysis are compared to that of Australian network standard level.

Power management and control strategies for efficient operation of a solar power dominated hybrid DC microgrid for remote power applications

In this paper, a hybrid DC microgrid consisting of a diesel generator with a rectifier, a solar photovoltaic (PV) system, and a battery energy storage system is presented in relation to an effective power management strategy and different control techniques are adopted to power electronic interfaces. The solar PV and battery energy storage systems are considered as the main sources of energy sources that supply the load demand on a daily basis whereas the diesel generator is used as a backup for the emergency operation of the microgrid. All system components are connected to a common DC bus through an appropriate power electronics devices (e.g., rectifier systems, DC/DC converter). Also a detailed sizing philosophy of all components along with the energy management strategy is proposed. Energy distribution pattern of each individual component has been conducted based on the monthly basis along with a power management algorithm. The power delivered by the solar PV system and diesel generator is controlled via DC-DC converterand excitation controllers which are designed based on a linearquadratic regulator (LQR) technique as as proportional integral (PI)controllers. The component level power distribution is investigatedusing these controllers under fluctuating load and solar irradiationconditions and comparative results are presented.

Minimizing energy consumption of yarn winding in ring spinning

Ring spinning has been and will continue to be an important system for making staple yarns from different fibers in the textile industry. But high power consumption and low productivity remain the two outstanding problems with ring spinning. Based on an analysis of power distribution during yarn winding in ring spinning, models for the ratio of energy consumption to yarn production over a full yarn package are established. Spindle speed, yarn count, and package diameter are the three key parameters affecting this ratio. The effects on energy consumption of these parameters are discussed through a case study. The energy-to-production ratio increases with increased package diameter but decreases with increased spindle speed and/or yarn count (tex). The results will help guide spinners in minimizing energy consumption in ring spinning.

Relationship between workplace reform and workforce participation

This thesis sought to advance understanding of the politics of workplace reform, explaining the respective roles of management and employees and how they relate. The literature on workplace reform usually argues that reform is predicated on greater workforce participation in managerial decisions. More specifically, different approaches to workplace reform can be aligned to different forms of participation. Thus quality management can be associated with direct forms of participation, institutional workplace reform may depend on representative forms, and best practice may require a combination of both. This thesis uses empirical evidence to explore this alignment between the different approaches to workplace reform and forms of participation. The period chosen for empirical study is approximately 1985-1992 - an era of rapid innovation in workplace reform for Australian manufacturing. Three workplaces were chosen for intensive study from automotive component manufacturers because that industry was itself a laboratory for workplace reform and also because these firms exemplified different approaches to competitiveness and reform. Three approaches to workplace reform - quality management, institutional workplace reform, and best practice - were distinguished to capture the range of Australian practice at that time. Similarly two approaches to workplace participation were distinguished - direct and representative - to reflect the range of observable practices at that time and to represent competing philosophies. Direct participation illustrated an approach founded in managerial context of the political status quo, whilst representative forms were considered to permit a pluralist shift of power to enable employees to manage in place of management. The three case studies depict companies sharing the competitive crisis of their industry. From this stems the impetus for workplace reform. At this point the firms diverged in their choice of competitive strategies for workplace reform. The case studies reveal, at the superficial level, a match between the chosen approaches to workplace reform and forms of participation. Basically, quality management is associated with direct employee participation, institutional workplace reform with collective bargaining and representative consultative committees, and best practice with both. However when the implementation of reform and participation are examined this match becomes less significant. One firm, Auto Air, achieved highly effective outcomes in both reform and participation. Another firm, Auto Electrical, failed in both. The thesis concluded that the relationship between forms of participation and reform is less significant than the effective implementation of policy. Unitarist or pluralist approaches to power distribution count less than managerial capacity to integrate successive reform initiatives and their commitment to workforce participation hi change.

International collaboration for women in IT : how to avoid reinventing the wheel

This paper uses information contributed by ACM-W Ambassadors from nine countries to build a picture of women working to improve the gender balance in IT around the world. The focus on women’s participation in education, the workforce and the political arena is presented using Hofstede and Hofstede’s (2005) dimensions of cultural masculinity, power distribution and individuality for each of the ACM-W Ambassador countries to set the scene. It is apparent from this compilation of information that different social and cultural climates in many parts of the world will necessitate different actions by ACM-W Ambassadors in their respective countries. While the ACM-W Ambassador program provides a forum for ideas, support and strategies to deal with the under-representation of women in IT, many of the current Ambassadors have more pressing issues to deal with, and indeed a ‘one size for all’ model for programs to promote IT to women will not be suitable. Exploring the network from an Australian perspective this work demonstrates that much is to be gained from increasing international networks to share the strategies and support required to encourage more women into IT.

The hidden permutation model and location-based activity recognition

Permutation modeling is challenging because of the combinatorial nature of the problem. However, such modeling is often required in many real-world applications, including activity recognition where subactivities are often permuted and partially ordered. This paper introduces a novel Hidden Permutation Model (HPM) that can learn the partial ordering constraints in permuted state sequences. The HPM is parameterized as an exponential family distribution and is flexible so that it can encode constraints via different feature functions. A chain-flipping Metropolis-Hastings Markov chain Monte Carlo (MCMC) is employed for inference to overcome the O(n!) complexity. Gradient-based maximum likelihood parameter learning is presented for two cases when the permutation is known and when it is hidden. The HPM is evaluated using both simulated and real data from a location-based activity recognition domain. Experimental results indicate that the HPM performs far better than other baseline models, including the naive Bayes classifier, the HMM classifier, and Kirshner's multinomial permutation model. Our presented HPM is generic and can potentially be utilized in any problem where the modeling of permuted states from noisy data is needed.

Effects of task lighting on visual function in age-related macular degeneration

The purpose was to investigate the effects of the spectral power distribution (SPD) and illuminance of task lighting on visual function in age-related macular degeneration (ARMD) compared to normal healthy eyes. Twenty-eight subjects with ARMD and 18 age-matched normal subjects were studied. The effects on visual function were determined for four common task light sources: standard pearl coat incandescent (SP), daylight blue incandescent (DL), warm white fluorescent (WW) and cool white fluorescent (CW). Apart from a small, statistically significant improvement in contrast sensitivity with DL compared to SP lighting (0.5 dB, p = 0.01), there were no significant effects of SPD on other visual functions and no differences in the effects for subjects with ARMD and those with normal vision. Thus, for task lighting typically used in low vision rehabilitation, the SPD would seem to be of minimal clinical importance to visual function. However, increasing the task illuminance had a greater effect on visual function, in particular for subjects with ARMD (p < 0.01). For an increase in illuminance from 300 to 3000 lux, the mean increase in contrast sensitivity and near visual acuity was 1.5 dB and 0.13 log MAR, respectively. Although this effect is not large, we suggest that it is clinically relevant and supports the provision of additional task illuminance as an important part of low vision rehabilitation for patients with ARMD.

Effect of elastic modulus and poisson's ratio on guided wave dispersion using transversely isotropic material modelling

Timber poles are commonly used for telecommunication and power distribution networks, wharves or jetties, piling or as a substructure of short span bridges. Most of the available techniques currently used for non-destructive testing (NDT) of timber structures are based on one-dimensional wave theory. If it is essential to detect small sized damage, it becomes necessary to consider guided wave (GW) propagation as the behaviour of different propagating modes cannot be represented by one-dimensional approximations. However, due to the orthotropic material properties of timber, the modelling of guided waves can be complex. No analytical solution can be found for plotting dispersion curves for orthotropic thick cylindrical waveguides even though very few literatures can be found on the theory of GW for anisotropic cylindrical waveguide. In addition, purely numerical approaches are available for solving these curves. In this paper, dispersion curves for orthotropic cylinders are computed using the scaled boundary finite element method (SBFEM) and compared with an isotropic material model to indicate the importance of considering timber as an anisotropic material. Moreover, some simplification is made on orthotropic behaviour of timber to make it transversely isotropic due to the fact that, analytical approaches for transversely isotropic cylinder are widely available in the literature. Also, the applicability of considering timber as a transversely isotropic material is discussed. As an orthotropic material, most material testing results of timber found in the literature include 9 elastic constants (three elastic moduli and six Poisson's ratios), hence it is essential to select the appropriate material properties for transversely isotropic material which includes only 5 elastic constants. Therefore, comparison between orthotropic and transversely isotropic material model is also presented in this article to reveal the effect of elastic moduli and Poisson's ratios on dispersion curves. Based on this study, some suggestions are proposed on selecting the parameters from an orthotropic model to transversely isotropic condition.