Transport properties in ionic liquids and ionic liquid mixtures : the challenges of NMR pulsed field gradient diffusion measurements

Pulsed field gradient NMR is a powerful method for the measurement of diffusion coefficients in liquids and solids and has begun to attract much attention in the ionic liquids field. However, aspects of the methodology as traditionally applied to solutions may not be uniformly applicable in these more viscous and chemically complex systems. In this paper we present data which shows that the Pulsed Gradient Spin Echo (PGSE) method in particular suffers from intrinsic internal gradients and can produce apparent diffusion coefficients which vary by as much as 20% for different ¹H nuclei within a given moleculean obvious anomaly. In contrast, we show that the Pulsed Gradient Stimulated Echo method does not suffer from this problem to the same extent and produces self-consistent data to a high degree of accuracy (better than 1%). This level of significance has allowed the detection, in this work, of subtle mixing effects in [C₃mpyr][NTf₂] and [C₄mpyr][NTf₂] mixtures.

Ion and solvent dynamics in gel electrolytes based on ethylene oxide grafted acrylate polymers

Multinuclear pulsed field gradient NMR measurements and rheological viscosity measurements were performed on three series of polymer gel electrolytes. The gels were based on a lithium salt electrolyte swollen into a copolymer matrix comprising an acrylate backbone and ethylene oxide side chains. In each series the side chains differed in length and number, but the acrylate-to-ethylene oxide ratio was kept constant. It was found that the self-diffusion coefficient of the cations was much lower than that of the anions, and that it decreased rapidly when the side chains got longer. In contrast, the self-diffusion coefficient of the anions was found to be independent of chain length. In the gel electrolytes, the diffusion coefficients of the solvent molecules are relatively constant despite an increased viscosity with increasing length of the side chains. However, in salt-free gels made for comparison, the diffusion coefficients of the solvent molecules decreased with increasing length of the side chains, which is consistent with an increased viscosity.

Australian Enterococcal Sepsis Outcome Programme, 2011

From 1 January to 31 December 2011, 29 institutions around Australia participated in the Australian Enterococcal Sepsis Outcome Programme (AESOP). The aim of AESOP 2011 was to determine the proportion of enterococcal bacteraemia isolates in Australia that are antimicrobial resistant, with particular emphasis on susceptibility to ampicillin and the glycopeptides, and to characterise the molecular epidemiology of the Enterococcus faecalis and E. faecium isolates. Of the 1,079 unique episodes of bacteraemia investigated, 95.8% were caused by either E. faecalis (61.0%) or E. faecium (34.8%). Ampicillin resistance was detected in 90.4% of E. faecium but not detected in E. faecalis. Using Clinical and Laboratory Standards Institute breakpoints (CLSI), vancomycin non-susceptibility was reported in 0.6% and 31.4% of E. faecalis and E. faecium respectively and was predominately due to the acquisition of the vanB operon. Approximately 1 in 6 vanB E. faecium isolates however, had an minimum inhibitory concentration at or below the CLSI vancomycin susceptible breakpoint of ≤ 4 mg/L. Overall, 37% of E. faecium harboured vanA or vanB genes. Although molecular typing identified 126 E. faecalis pulsed-field gel electrophoresis (PFGE) pulsotypes, more than 50% belonged to 2 pulsotypes that were isolated across Australia. E. faecium consisted of 73 PFGE pulsotypes from which 43 multilocus sequence types were identified. Almost 90% of the E. faecium were identified as clonal complex 17 clones, of which approximately half were characterised as sequence type 203, which was isolated Australia-wide. In conclusion, the AESOP 2011 has shown that although polyclonal, enterococcal bacteraemias in Australia are frequently caused by ampicillin-resistant vanB E. faecium.

Australian Enterococcal Sepsis Outcome Programme annual report, 2013.

From 1 January to 31 December 2013, 26 institutions around Australia participated in the Australian Enterococcal Sepsis Outcome Programme (AESOP). The aim of AESOP 2013 was to determine the proportion of enterococcal bacteraemia isolates in Australia that are antimicrobial resistant, and to characterise the molecular epidemiology of the Enterococcus faecium isolates. Of the 826 unique episodes of bacteraemia investigated, 94.6% were caused by either E. faecalis (56.1%) or E. faecium (38.5%). Ampicillin resistance was not detected in E. faecalis but was detected in over 90% of E. faecium. Vancomycin non-susceptibility was reported in 0.2% and 40.9% of E. faecalis and E. faecium respectively and was predominately due to the acquisition of the vanB operon. Overall, 41.6% of E. faecium harboured vanA or vanB genes. The percentage of E. faecium bacteraemia isolates resistant to vancomycin in Australia is significantly higher than that seen in most European countries. E. faecium isolates consisted of 81 pulsed-field gel electrophoresis pulsotypes of which 72.3% were classified into 14 major pulsotypes containing five or more isolates. Multilocus sequence typing grouped the 14 major pulsotypes into clonal cluster 17, a major hospital-adapted polyclonal E. faecium cluster. Of the 2 predominant sequence types, ST203 (80 isolates) was identified across Australia and ST555 (40 isolates) was isolated primarily in the western and central regions (Northern Territory, South Australia and Western Australia) respectively. In conclusion, the AESOP 2013 has shown enterococcal bacteraemias in Australia are frequently caused by polyclonal ampicillin-resistant high-level gentamicin resistant vanB E. faecium, which have limited treatment options.

Ion transport in polymer electrolytes containing nanoparticulate TiO2 : The influence of polymer morphology

Recent studies have shown that composite polymer electrolytes, formed by dispersing nanosized ceramic particles in polyether-based electrolytes, have improved ion transport properties as compared to their unfilled analogues. In the present study polymer electrolytes with different loadings of nano-sized ceramic particles (TiO₂) and different polymer chemistry and morphology have been investigated. Of special interest are filler induced effects on polymer, solvent and cationic mobility. Partly crystalline polymer electrolytes based on poly(ethylene oxide) have been compared to fully amorphous polymer electrolytes based on a polyether urethane, as well as gel electrolytes based on PMMA. ⁷Li pfg-NMR, linewidth and spin–spin relaxation times as well as ¹H pfg-NMR and spin–spin relaxation times, were measured as a function of temperature and composition. The ¹H spin–spin relaxation measurements reveal increased average polymer mobility with the addition of filler up to a maximum at 4 and 8 wt.% TiO₂ for the fully amorphous and the partly crystalline electrolytes, respectively. The ⁷Li linewidth measurements for the fully amorphous system show a broadening of the linewidth with addition of filler. Based on variable temperature measurements this broadening is interpreted as a result of the inhomogeneity introduced by the filler particles. Pulsed field gradient (pfg) diffusion measurements were employed to determine ion and solvent self-diffusion coefficients. In the case of the PMMA-based gel electrolyte and the fully amorphous electrolytes enhanced cation self-diffusion was observed upon addition of TiO₂.

Polyelectrolyte-in-ionic-liquid electrolytes

Novel polymer electrolyte materials based on a polyelectrolyte-in-ionic-liquid principle are described. A combination of a lithium 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPSLi) and N,N′-dimethylacrylamide (DMMA) are miscible with the ionic liquid, 1-ethyl-3-methylimidazolium dicyanamide (EMIDCA). EMIDCA has remarkably high conductivity (≥ 2 · 10−2 S · cm−1) at room temperature and acts as a good solvating medium for the polyelectrolyte. At compositions of AMPSLi less than or equal to 75 mol-% in the copolymer (P(AMPSLi-co-DMAA)), the polyelectrolytes in EMIDCA are homogeneous, flexible elastomeric gel materials at 10 − 15 wt.-% of total polyelectrolyte. Conductivities higher than 8 · 10−3 S · cm−1 at 30 °C have been achieved. The effects of the monomer composition, polyelectrolyte concentration, temperature and lithium concentration on the ionic conductivity have been studied using thermal and conductivity analysis, and pulsed field gradient nuclear magnetic resonance techniques.

Solid state ion transport and phase behaviour in composites of N,N-methyl propylpyrrolidinium tetrafluoroborate and amorphous polyethylene oxide

The binary and ternary addition of 2 wt.% LiBF₄ and 2 wt.% amorphous polyethylene oxide (aPEO) respectively to the plastic crystal forming salt P₁₃BF₄ (where P₁₃⁺=methylpropyl pyrrolidinium cation) was investigated with specific focus on the phase behaviour and evaluation of transport characteristics. Differential scanning calorimetry (DSC), optical thermomicroscopy, solid state nuclear magnetic resonance (NMR), and AC impedance spectroscopy were used to develop an understanding of the conduction process in the pure and mixed systems. The morphology of the ternary compound appeared as hexagonal spherulites upon solidification. Multinuclear NMR Pulsed Field Gradient measurements (¹H,¹⁹F,⁷Li) to probe both cation and anion diffusion coefficients are reported. The anion is shown to be the most diffusive (at 320 K:¹⁹F=2.5×10⁻¹¹ m² s⁻¹; 1H: 1.8×10⁻¹¹ m² s⁻¹; ⁷Li: 1.1×10⁻¹¹ m² s⁻¹) in the ternary compound, with enhanced conductivity (2.7×10⁻⁵ S cm⁻¹ at 310 K) just below the melt.

Conductivity and NMR properties of plasticized polyethers complexed with lithium salts

NMR provides a tool whereby the dynamic properties of specific nuclei can be investigated. In the present study, a poly(ethylene oxide-co-propylene oxide) network has been used as the polymer host to prepare solid polymer electrolytes (SPE) containing either LiClO₄ or LiCF₃SO₃. In addition, a low molecular weight plasticizer [propylene carbonate (PC), dimethyl formamide (DMF) or tetraglyme] has been added to several of the samples to enhance the mobility of the polymer and, thus, of the ionic species. The effects of plasticizer and salt concentration on the ionic structure and mobility in these SPEs, as measured by NMR relaxation times, and correlation to the conductivity behaviour in these systems are discussed. Temperature dependent triflate diffusion coefficients, as measured by Pulsed Field Gradient ¹⁹F-NMR, in plasticized SPEs are also reported.

Fast ion conduction in molecular plastic crystals

Doping of lithium salts and acids into the plastic crystal phase of succinonitrile has shown for the first time of the possibility of creating solid state electrolytes based on plastic crystalline solvents where the matrix itself is neutral and hence not intrinsically conductive. These materials illustrate the concept of a solid state electrolyte solvent. Room temperature conductivities up to 3.4×10⁻⁴ S cm⁻¹ were obtained with 5 wt.% lithium bis(trifluoromethanesulfonylamide) in succinonitrile. Pulsed field gradient NMR measurements indicate that both cation and anion are mobile in this lattice. Proton conductivity was also observed when methane sulfonic acid or glacial acetic acid was used as dopants, however, the conductivity in these systems is limited by the poor dissociating ability of these acids.

Proton transport in choline dihydrogen phosphate/H3PO4 mixtures

Mixtures of the plastic crystal material choline dihydrogen phosphate [Choline][DHP] and phosphoric acid, from 4.5 mol% to 18 mol% H₃PO₄, were investigated and shown to have significantly higher proton conductivity compared to the pure [Choline][DHP]. This was particularly evident from the electrochemical hydrogen reduction reaction and the proton NMR diffusion measurements, in addition to ionic conductivity measured from the impedance spectroscopy. The ionic conductivity was observed to increase by more than an order of magnitude in phase I (i.e. the highest temperature solid phase in [Choline][DHP]) reaching up to 10⁻² S cm⁻¹. The multinuclear NMR spectroscopy data suggest that, at least on the timescale of the NMR measurement, the H⁺ cations and [DHP] anions are equivalent in both phases. The pulsed field gradient NMR diffusion measurements of the 18 mol% acid sample indicate that all three ions are mobile, however the H⁺ diffusion coefficient is an order of magnitude higher than for the [Choline] cation or the [DHP] anion, and therefore conduction in these materials is dominated by proton conductivity. The thermal stability, as measured by TGA, is unaffected with increasing acid additions and remains high; i.e. no significant mass loss below 200 °C.

Proton transport properties in zwitterion blends with brønsted acids

We describe zwitterion, 3-(1-butyl-1H-imidazol-3-ium-3-yl)propane-1-sulfonate (Bimps), mixtures with 1,1,1-trifluoro-N-(trifluoromethylsulfonyl)methanesulfoneamide (HN(Tf)₂) as new proton transport electrolytes. We report proton transport mechanisms in the mixtures based on results from several methods including thermal analyses, the complex-impedance method, and the pulsed field gradient spin echo NMR (pfg-NMR) method. The glass transition temperature (Tg) of the mixtures decreased with increasing HN(Tf)₂ concentration up to 50 mol %. The Tg remained constant at −55 °C with further acid doping. The ionic conductivity of HN(Tf)₂ mixtures increased with the HN(Tf)₂ content up to 50 mol %. Beyond that ratio, the mixtures showed no increase in ionic conductivity (10⁻⁴ S cm⁻¹ at room temperature). This tendency agrees well with that of Tg. However, the self-diffusion coefficients obtained from the pfg-NMR method increased with HN(Tf)₂ content even above 50 mol % for all component ions. At HN(Tf)₂ 50 mol %, the proton diffusion of HN(Tf)₂ was the fastest in the mixture. These results suggest that Bimps cannot dissociate excess HN(Tf)₂, that is, the excess HN(Tf)₂ exists as molecular HN(Tf)₂ in the mixtures. The zwitterion, Bimps, forms a 1:1 complex with HN(Tf)₂ and the proton transport property in this mixture is superior to those of other mixing ratios. Furthermore, CH₃SO₃H and CF₃SO₃H were mixed with Bimps for comparison. Both systems showed a similar tendency, which differed from that of the HN(Tf)₂ system. The Tg decreased linearly with increasing acid content for every mixing ratio, while the ionic conductivity increased linearly. Proton transport properties in zwitterion/acid mixtures were strongly affected by the acid species added.

Ionic liquid electrolyte for lithium metal batteries : physical, electrochemical, and interfacial studies of N-Methyl-N-butylmorpholinium Bis(fluorosulfonyl)imide

The ionic liquid (IL) N-methyl-N-butylmorpholinium bis(fluorosulfonyl)imide (C₄mmor FSI) is examined from physical and electrochemical perspectives. Pulsed field gradient NMR spectroscopy shows that ion diffusivities are low compared with similar, non-ethereal ILs. Ionicity values indicate that above room temperature, less than 50% of ions contribute to conductivity.

Lithium cycling in symmetrical cells using a C₄mmor FSI-based electrolyte is best demonstrated at elevated temperatures. Specific capacities of 130 mAh g⁻¹ are achieved in a Li−LiFePO₄ battery at 85 °C. FT-IR spectroscopic investigations of lithium electrodes suggest the presence of alkoxide species in the solid electrolyte interphase (SEI), implying a ring-opening reaction of C₄mmor with lithium metal. In contrast, the SEI derived from N-methyl-N-propylpiperidinium FSI lacks the alkoxide signature but shows signs of alkyl unsaturation, and the activation energy for Li+ transport through this SEI is slightly lower than that for the C₄mmor-derived SEI. Our detailed findings give insight into the capabilities and limitations of rechargeable lithium metal batteries utilizing a C₄mmor FSI electrolyte.

The effect of coordinating and non-coordinating additives on the transport properties in ionic liquid electrolytes for lithium batteries

In the present study we expand our analysis of using two contrasting organic solvent additives (toluene and THF) in an ionic liquid (IL)/Li NTf 2 electrolyte. Multinuclear Pulsed-Field Gradient (PFG) NMR, spin-lattice (T1) relaxation times and conductivity measurements over a wide temperature range are discussed in terms of transport properties and structuring of the liquid. The conductivity of both additive samples is enhanced the most at low temperatures, with THF slightly more effective than toluene. Both the anion and lithium self-diffusivity are enhanced in the same order by the additives (THF > toluene) while that of the pyrrolidinium cation is marginally enhanced. 1H spin-lattice relaxation times indicate a reasonable degree of structuring and anisotropic motion within all of the samples and both 19F and 7Li highlight the effectiveness of THF at influencing the lithium coordination within these systems.

Permeability mapping in porous media by magnetization prepared centric-scan SPRITE

The ability of porous media to transmit fluids is commonly referred to as permeability. The concept of permeability is central for hydrocarbon recovery from petroleum reservoirs and for studies of groundwater flow in aquifers. Spatially resolved measurements of permeability are of great significance for fluid dynamics studies. A convenient concept of local Darcy’s law is suggested for parallel flow systems. The product of porosity and mean velocity images in the plane across the average flow direction is directly proportional to permeability. Single Point Ramped Imaging with T 1 Enhancement (SPRITE) permits reliable quantification of local fluid content and flow in porous media. It is particularly advantageous for reservoir rocks characterized by fast magnetic relaxation of a saturating fluid. Velocity encoding using the Cotts pulsed field gradient scheme improves the accuracy of measured flow parameters. The method is illustrated through measurements of 2D permeability maps in a capillary bundle, glass bead packs and composite sandstone samples.

Porous carbon nanotube/polyvinylidene fluoride composite material: Superhydrophobicity/superoleophilicity and tunability of electrical conductivity

Porous carbon nanotube/polyvinylidene fluoride (CNT/PVDF) composite material can be fabricated via formation and freeze-drying of a gel. The field emission scanning electron microscopy, nitrogen adsorption-desorption and pore size distribution analysis reveal that the introduction of a small amount of carbon nanotubes (CNTs) can effectively increase the surface roughness and porosity of polyvinylidene fluoride (PVDF). Contact angle measurements of water and oil indicate that the as-obtained composite material is superhydrophobic and superoleophilic. Further experiments demonstrate that these composite material can be efficiently used to separate/absorb the insoluble oil from oil polluted water as membrane/absorbent. Most importantly, the electrical conductivity of such porous CNT/PVDF composite material can be tuned by adjusting the mass ratio of CNT to PVDF without obviously changing the superhydrophobicity or superoleophilicity. The unique properties of the porous CNT/PVDF composite material make it a promising candidate for oil-polluted water treatment as well as water-repellent catalyst-supporting electrode material.