Electrical characterization of new electrochromic devices

Electrochromic devices change their color and optical properties with applied voltage. A new symmetrical electrochromic configuration was constructed in previous works, where PEDOT acted as electrochromic layer or as counter electrode layer, depending on the polarity of the applied voltage. Devices of around 500mm2 and switching voltages from 0,5V to 2V are used in this work. Measured electrochemical impedance is fitted to an equivalent circuit based on a Randles cell, with Warburg impedance simulating ionic diffusion at low frequencies. Voltage dependence is analyzed for the first time in this kind of devices. Results show homogeneity problems in the contact layers, not seen in normal operation, and the voltage dependence on some construction parameters. This will be used to improve the devices construction, but improvements in the equivalent circuit should also be made. The proposed equivalent circuit is not valid after the redox reaction, from 1.5 to 2V.

Inverse opal structure of SnO2 and SnO2 : Zn for gas sensing

In the present work, we propose a low cost synthetic sol-gel route that allows to produce high quality oxide nanostructures with inverse opal architecture which, transferred on alumina substrates provided with Pt interdigitated contacts and heater, are tested as gas sensing devices. An opal template of sintered monodisperse polystyrene spheres was filled with alcoholic solutions of metal oxide precursors and transferred on the alumina substrate. The polystyrene template was removed by thermal treatment, leading to the simultaneous sintering of the oxide nanoparticles. Beside SnO₂, a binary oxide well known for gas sensing application, a Zn containing ternary solid solution (SnO₂:Zn, with Zn 10% molar content) was taken into account for sensor preparation. The obtained high quality macro and meso-porous structures, characterized by different techniques, were tested for pollutant (CO, NO₂) and interfering (methanol) gases, showing that very good detection can be reached through the increase of surface area offered by the inverse opal structure and the tailoring of the chemical composition. The electrical characterization performed on the tin dioxide based sensors shows an enhancement of the relative response towards NO₂ at low temperatures in comparison with conventional SnO₂ sensors obtained with sputtering technique. The addition of Zn increases the separation between the operating temperatures for reducing and oxidizing gases and results in a further enhancement of the selectivity to NO₂ detection.

Inverse opal nanoassemblies : novel architectures for gas sensors the SnO2:Zn case

A novel technique is here presented, based on inverse opal metal oxide structures for the production of high quality macro and meso-porous structures for gas sensing. Taking advantage of a sol-gel templated approach. different mixed semiconducting oxides with high surface area, commonly used in chemical sensing application, were synthesized. In this work we report the
comparison between SnO₂ and SnO₂:Zn. As witnessed by Scanning and Transmission Electron Microscopy (SEM and TEM) analyses and by Powder x-ray Diffraction (PX RD), highly ordered meso-porous structures were formed with oxide crystalline size never exceeding 20 nm . The filled templates. in form of thick films, were bound to allumina substrate with Pt interdigitated contacts
and Pt heater, through in situ calcination, in order to perform standard electrical characterization. Pollutant gases like CO and NO₂ and methanol. as interfering gas, were used for the targeted electrical gas tests. All samples showed low detection limits towards both reducing and oxidizing species in low temperature measurements. Moreover, the addition of high molar percentages of Zn( II) affected the beha viour of electrical response improv ing the se lecti vity of the proposed system.

Characterization of conductive polyprrole coated wool yarns

Wool yarns were coated with conducting polypyrrole by chemical synthesis methods. Polymerization of pyrrole was carried out in the presence of wool yarn at various concentrations of the monomer and dopant anion. The changes in tensile, moisture absorption, and electrical properties of the yarn upon coating with conductive polypyrrole are presented. Coating the wool yarns with conductive polypyrrole resulted in higher tenacity, higher breaking strain, and lower initial modulus. The changes in tensile properties are attributed to the changes in surface morphology due to the coating and reinforcing effect of conductive polypyrrole. The thickness of the coating increased with the concentration of p-toluene sulfonic acid, which in turn caused a reduction in the moisture regain of the wool yarn. Reducing the synthesis temperature and replacing p-toluenesulfonic acid by anthraquinone sulfonic acid resulted in a large reduction in the resistance of the yarn.

Optimal trajectory characterization for a pursuer navigation scheme

In this paper we examine the geometry of a number of bearing-only navigation schemes for guiding a pursuer from a fixed initial position to a final target position. We explicitly characterize the optimal trajectories for the given problems in terms of analyzing those trajectories which attempt to minimize the error in an estimate of the target position using successive bearing measurements made along the trajectory.

Characterization and evaluation of BaCo0.7Fe0.2Nb0.1O3−δ as a cathode for proton-conducting solid oxide fuel cells

This study characterizes BaCo0.7Fe0.2Nb0.1O3−δ (BCFN) perovskite oxide and evaluates it as a potential cathode material for proton-conducting SOFCs with a BaZr0.1Ce0.7Y0.2O3-δ (BZCY) electrolyte. A four-probe DC conductivity measurement demonstrated that BCFN has a modest electrical conductivity of 2–15 S cm−1 in air with p-type semiconducting behavior. An electrical conductivity relaxation test showed that BCFN has higher Dchem and Kchem than the well-known Ba0.5Sr0.5Co0.8Fe0.2O3−δ oxide. In addition, it has relatively low thermal expansion coefficients (TECs) with values of 18.2 × 10−6 K−1 and 14.4 × 10−6 K−1 at temperature ranges of 30–900 °C and 30–500 °C, respectively. The phase reaction between BCFN and BZCY was investigated using powder and pellet reactions. EDX and XRD characterizations demonstrated that BCFN had lower reactivity with the BZCY electrolyte than strontium-containing perovskite oxides such as SrCo0.9Nb0.1O3-δ and Ba0.6Sr0.4Co0.9Nb0.1O3−δ. The impedance of BCFN was oxygen partial pressure dependent. Introducing water into the cathode atmosphere reduced the size of both the high-frequency and low-frequency arcs of the impedance spectra due to facilitated proton hopping. The cathode polarization resistance and overpotential at a current density of 100 mA cm−2 were 0.85 Ω cm−2 and 110 mV in dry air, which decreased to 0.43 Ω cm−2 and 52 mV, respectively, in wet air (∼3% H2O) at 650 °C. A decrease in impedance was also observed with polarization time; this was possibly caused by polarization-induced microstructure optimization. A promising peak power density of ∼585 mW cm−2 was demonstrated by an anode-supported cell with a BCFN cathode at 700 °C.

Fabrication, characterization and modelling of functionally graded nanocomposites

This research introduced the innovative concept of controlling the composition in nanocomposites for optimizing the mechanical performance; as well as tailoring the thermal and electrical properties for multi-functional applications. It led to the development of novel lighter stronger materials for use in engineering applications such as automotive body and mining equipment.

Characterization and optimization to improve uneven surface on MEMS bridge fabrication

This paper presents an optimized fabrication method for developing a freestanding bridge for RF MEMS switches. In this method, the sacrificial layer is patterned and hard baked a 220°C for 3min, after filling the gap between the slots of the coplanar waveguide. Measurement results by AFM and SEM demonstrate that this technique significantly improves the planarity of the sacrificial layer, reducing the uneven surface to less than 20nm, and the homogeneity of the Aluminum thickness across the bridge. Moreover, a mixture of O2, Ar and CF4 was used and optimized for dry releasing of the bridge. A large membrane (200×100μm2) was released without any surface bending. Therefore, this method not only simplifies the fabrication process, but also improves the surface flatness and edge smoothness of the bridge. This fabrication method is fully compatible with standard silicon IC technology.