Distributed generation capacity planning for distribution networks to minimize energy loss: an unbalanced multi-phase optimal power flow based approach

This chapter presents an unbalanced multi-phase optimal power flow (UMOPF) based planning approach to determine the optimum capacities of multiple distributed generation units in a distribution network. An adaptive weight particle swarm optimization algorithm is used to find the global optimum solution. To increase the efficiency of the proposed scheme, a co-simulation platform is developed. Since the proposed method is mainly based on the cost optimization, variations in loads and uncertainties within DG units are also taken into account to perform the analysis. An IEEE 123 node distribution system is used as a test distribution network which is unbalanced and multi-phase in nature, for the validation of the proposed scheme. The superiority of the proposed method is investigated through the comparisons of the results obtained that of a Genetic Algorithm based OPF method. This analysis also shows that the DG capacity planning considering annual load and generation uncertainties outperform the traditional well practised peak-load planning.

Boron carbide nanowires with uniform CNχ coatings

Boron carbide nanowires with uniform carbon nitride coating layers were synthesized on a silicon substrate using a simple thermal process. The structure and morphology of the as-synthesized nanowires were characterized using x-ray diffraction, scanning and transmission electron microscopy and electron energy loss spectroscopy. A correlation between the surface smoothness of the nanowire sidewalls and their lateral sizes has been observed and it is a consequence of the anisotropic formation of the coating layers. A growth mechanism is also proposed for these growth phenomena.

Preparation and characterization of graphitic carbon nitride through pyrolysis of melamine

Graphitic carbon nitride (g-C₃N₄) has been synthesized via a two-step pyrolysis of melamine (C₃H₆N₆) at 800°C for 2 h under vacuum conditions. X-ray diffraction (XRD) patterns strongly indicate that the synthesized sample is g-C₃N₄. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) morphologies indicate that the product is mainly composed of graphitic carbon nitride. The stoichiometric ratio of C:N is determined to be 0.72 by elemental analysis (EA). Chemical bonding of the sample has been investigated by X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). Electron energy loss spectroscopy (EELS) verifies the bonding state between carbon and nitrogen atoms. Optical properties of the g-C₃N₄ were investigated by PL (photoluminescence) measurements and UV–Vis (ultraviolet–visible) absorption spectra. We suppose its luminescent properties may have potential application as component of optical nanoscale devices. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were also performed.

Poly(triazine imide) with intercalation of Lithium and ChlorideiIons [(C3N3)2(NHxLi1−x)3⋅LiCl]: A Crystalline 2D Carbon Nitride network

Poly(triazine imide) with intercalation of lithium and chloride ions (PTI/Li+Cl−) was synthesized by temperature-induced condensation of dicyandiamide in a eutectic mixture of lithium chloride and potassium chloride as solvent. By using this ionothermal approach the well-known problem of insufficient crystallinity of carbon nitride (CN) condensation products could be overcome. The structural characterization of PTI/Li+Cl− resulted from a complementary approach using spectroscopic methods as well as different diffraction techniques. Due to the high crystallinity of PTI/Li+Cl− a structure solution from both powder X-ray and electron diffraction patterns using direct methods was possible; this yielded a triazine-based structure model, in contrast to the proposed fully condensed heptazine-based structure that has been reported recently. Further information from solid-state NMR and FTIR spectroscopy as well as high-resolution TEM investigations was used for Rietveld refinement with a goodness-of-fit (χ2) of 5.035 and wRp=0.05937. PTI/Li+Cl− (P63cm (no. 185); a=846.82(10), c=675.02(9) pm) is a 2D network composed of essentially planar layers made up from imide-bridged triazine units. Voids in these layers are stacked upon each other forming channels running parallel to [001], filled with Li+ and Cl− ions. The presence of salt ions in the nanocrystallites as well as the existence of sp2-hybridized carbon and nitrogen atoms typical of graphitic structures was confirmed by electron energy-loss spectroscopy (EELS) measurements. Solid-state NMR spectroscopy investigations using 15N-labeled PTI/Li+Cl− proved the absence of heptazine building blocks and NH2 groups and corroborated the highly condensed, triazine-based structure model.

Energy dissipation and geometry effects over stepped spillways

The energy dissipation process is the major significant point in the designof hydraulic structure. The dissipation of high energy on stepped weirsprevents any damage in the weir itself and channels the energy ownstream to reduce the stilling basin size. In this study, four physical models are used to evaluate the impact of adding end sills that have a quarter circle shape at step edges. The amount of energy loss on weirs under different flow regimes is investigated by experimental work. Stepped weirs have a suitable number of steps and two different ratios of the width to height (2.22, and 2.40). The scale of the physical models is 20:1. The outcomes of the dimensional analyses refer to the critical depth for flow in weirs to the height of step yc/h, the end sill radius, and the number of steps N are more effective parameters than others inthe energy loss process. Moreover, for small values of yc/h, the energydissipation is the greatest. Any increase in yc/h leads to a decrease in theenergy dissipation, while the energy dissipation increases with the number of steps (N).

An investigation of the native oxide of aluminum alloy 7475-T7651 using XPS, AES, TEM, EELS, GDOES, RBS.

The native oxide on the rolled aerospace aluminum alloy 7475-T7651 was characterized using a variety of different techniques, including X-ray Photoelectron Spectrometry (XPS), Auger Electron Spectrometry (AES), Transmission Electron Microscopy (TEM), Electron Energy Loss Spectrometry (EELS), Glow Discharge Optical Emission Spectrometry (GDOES), and Rutherford Backscattered Spectrometry (RBS). All techniques revealed that the native oxide layer is magnesium-rich and is probably a mixture of magnesium and aluminum–magnesium oxides.1 The oxide layer was found to be of nonuniform thickness due to the rolling process involved during the manufacture of this sheet alloy; this complicates analysis using techniques which have poor spatial resolution. Direct thickness measurement from cross-sectional TEM reveals an oxide thickness which varies between 125 and 500 nm. This large variation in thickness was also evident from GDOES and AES depth profiles as well asthe RBS data. Both XPS and RBS also show evidence for the presence of heavy metals in the oxide.

Substitution reactions of carbon nanotube template

Substitution reactions between carbon nanotube (CNT) template and SiO with the formation of carbon rich silicon oxide nanowires (SiO–C-NWs) have been investigated using transmission electron microscopy and x-ray energy dispersive spectroscopy. The reaction was carried out by thermal annealing at 1200 °C for 1 h of a mixture of silicon monoxide (SiO) and iron (II) phthalocyanine, FeC32N8H16 (FePc) powders. Multiwalled CNTs were produced first via pyrolysis of FePc at a lower temperature (1000 °C). SiO vapors reacted with the CNTs at higher temperatures to produce amorphous SiO–C-NWs with a uniform diameter and a length in tens of micrometers. The special bamboolike structure of the CNTs allows the reaction to start from the external surface of the tubes and transform each CNT into a solid nanowire section by section.

Preparation of bioactive porous Ti-Sn-Nb alloy for biomedical applications

A porous Ti-16Sn-4Nb alloy with an average pore size of 300 µm and porosity of 60 % was prepared by powder metallurgy, and a bone-like apatite coating was obtained by soaking the samples in a concentrated simulated body fluid (lOx SBF). The changes of the microstructure and composition on the surface with soaking time were investigated by using X-ray diffractometry (XRD), and scanning electron microscopy equipped with energy dispersive spectroscopy (SEM-EDS), The bone-like apatite granules started to deposit throughout the porous Ti alloy foam aner 1 h soaking, and the number of granules increased with the increase of the soaking time. A uniform bone-like apatite layer covered the entire surface of the sample after soaking in Ihe lOx SBF for 6h. The Ti-16Sn-4Nb foam showed a good bioactivity after a thermochemical process and soaking into a 1Ox SBF.

Microstructural development in Al/MgAl2O4 in situ metal matrix composite using value-added silica sources

Al/MgAl2O4 in situ metal matrix composites have been synthesized using value-added silica sources (microsilica and rice husk ash) containing ~97% SiO2 in Al-5 wt.% Mg alloy. The thermodynamics and kinetics of MgAl2O4 formation are discussed in detail. The MgO and MgAl2O4 phases were found to dominate in microsilica (MS) and rice husk ash (RHA) value-added composites, respectively, during the initial stage of holding the composites at 750 °C. A transition phase between MgO and MgAl2O4 was detected by the scanning electron microscopy and energy-dispersive spectroscopy (SEM–EDS) analysis of the particles extracted from the composite using 25% NaOH solution. This confirms that MgO is gradually transformed to MgAl2O4 by the reaction 3SiO2(s)+2MgO(s)+4Al(l)→2MgAl2O4(s)+3Si(l). The stoichiometry of MgAl2O4, n, computed by a new methodology is between 0.79 and 1.18. The reaction between the silica sources and the molten metal stopped after 55% of the silica source was consumed. A gradual increase in mean MgAl2O4 crystallite size, D, from 24 to 36 nm was observed in the samples held for 10 h.

Phosphonium ionic liquids as lubricants for aluminium-steel

The performance of a series of novel room temperature ionic liquids (ILs) based on the trihexyl(tetradecyl)phosphoniumcation (P66614 +) and a number of novel anions have been studied in pin-on-disk tests using a 100Cr6 steel ball on AA2024 aluminium disks.

The anions coupled to the (P66614 +) cation include diphenyl phosphate (DPP-), dibutyl phosphate (DBP-), bis (2,4,4-trimethyl pentyl) phosphinate (M3PPh-) and bis(2-ethyl hexyl) phosphate (BEH-).

More traditional anions such as bis(trifluoromethanesulfonyl) amide (NTf2 -) and bromide (Br-) were also investigated. Experiments were conducted at various loads to assess the IL film forming abilities.

The results suggest that the structure of the anion is important in forming a surface film that reduces the friction and wear of the aluminium disk. At 30N five of the six ILs tested showed a 30-90% reduction in wear, as determined from wear scar depth measurements, compared to fully formulated diesel oil.

The IL lubricant with a diphenyl phosphate anion achieved the lowest wear coefficient, showing a better performance than a typical fluorine-containing IL anion, NTf2.

To further investigate wear mechanisms and surface interactions the wear scars were analysed using a scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS).

Feast or famine : evidence for mixed capital–income breeding strategies in Weddell seals

Evolved patterns of resource expenditure for reproduction have resulted in a life history continuum across species. A strictly capital-breeding strategy relies extensively on stored energy for reproduction, whereas income breeding uses energy acquired throughout the reproductive period. However, facultative income breeding has been shown in some classically capital-breeding animals, and was originally thought to provide a nutritional refuge for smaller females incapable of securing sufficient reserves during pre-partum foraging. We examined milk composition and milk output for the Weddell seal to determine to what degree lactation was aided by food intake, and what factors contributed to its manifestation. Milk composition was independent of maternal post-partum mass and condition, but did change over lactation. Changes were most likely in response to energetic and nutritional demands of the pup at different stages of development. During early lactation, females fasted and devoted 54.9% of total energy loss to milk production. Later in lactation 30.5% more energy was devoted to milk production and evidence suggested that larger females fed more during lactation than smaller females. It appears that Weddell seals may exhibit a flexible strategy to adjust reproductive investment to local resource levels by taking advantage of periods when prey are occasionally abundant, although it is restricted to larger females possessing the physiological capacity to dive for longer and exploit different resources during lactation. This supports the assumption that although body mass and phylogenetic history explain most of the variation in lactation patterns (20–69%), the remaining variation has likely resulted from physiological adaptations to local environmental conditions. Our study confirms that Weddell seals use a mixed capital–income breeding strategy, and that considerable intraspecific variation exists. Questions remain as to the amount of energy gain derived from the income strategy, and the consequences for pup condition and survival.

Silkworm silk cocoon structure-property relationship

A collection of images examining the microstructure of raw cocoons. The research investigates how the microstructure varies from one layer to another in the same cocoon and also from one cocoon variety to another. The research is being undertaken to study the structure and property relationships, specifically the antibacterial properties, photodegradability and mechanical strength of different cocoon components - fibre, sericin, and crystals. The aim is to understand the role of different cocoon components and their mechanism of protecting the pupa from extremes of climatic conditions, microorganisms, and other pathogens and predators. Scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) were used to analyse the structure of the cocoons, fibre, and sericin.

A novel exhaust heat recovery system to reduce fuel consumption

Internal combustion engines release about 1/3 of the energy bound in the fuel as exhaust waste gas energy and another 1/3 energy is wasted through heat transfer into the ambient. On the other hand losses through friction are the third largest root cause for energy loss in internal combustion engines. During city driving frictional losses can be of the same size as the effective work, and during cold start these losses are even bigger. Therefore it is obvious to utilise wasted exhaust energy to warm up the engine oil directly. Frictional losses of any engine can be reduced during part load. Sensitivity analyses have been conducted for different concepts that utilise exhaust energy to reduce engine viscosity and friction. For a new system with an exhaust gas/oil heat exchanger the following benefits have been demonstrated:

• Fuel consumption reductions of over 7% measured as an average over 5 NEDC tests
compared to the standard system configuration.
• Significant reductions in exhaust emissions, mainly CO and NOx have been achieved
• Significantly higher oil temperatures during cold start indicate large potential to
reduce engine wear through reduced water condensation in the crankcase
• Fuel consumption reductions of further 3.3% to 4.6% compared to the 7% measured
over the NEDC test can be expected under real world customer usage conditions at
lower ambient temperatures.

Oil temperature measurements and analysis resulted in the idea of a novel system with further potential to reduce fuel consumption. This Oil Viscosity Energy Recovery System (OVER 7™) consists of 3 key features that add significant synergies if combined in a certain way: an oil warm up circuit/bypass, including oil pressure control and Exhaust Gas/Oil Heat Exchanger. The system separates the thermal inertias of the oil in the engine galleries and the oil pan, reduces hydraulic pumping losses, increases the heat transfer from the cylinder head to the oil, and utilises the exhaust heat to reduce oil friction.

The project demonstrated that sensitivity analysis is an important tool for the evaluation of different concepts. Especially for new concepts that include transient heat transfer such a qualitative approach in combination with accurate experiments and measurements can be faster and more efficient in leading to the desired improvements compared to time consuming detailed simulations.

The corrosion inhibition of aluminium alloy 7075-T651 with cerium and Mischmetal di phenyl phosphate

Previous studies have shown that cerium diphenyl phosphate (Cedpp) 3 is a very effective inhibitor of corrosion of aluminium alloys in chloride solutions. This paper describes the results of further studies using electrochemical and constant immersion corrosion tests to compare the effectiveness of Ce(dpp) 3 and Mischmetal diphenyl phosphate Mm(dpp) 3 as inhibitors of corrosion pitting on AA7075-T651 aluminium alloy. The results shows that both Ce(dpp) 3 and Mm(dpp) 3 are excellent inhibitors of pitting corrosion of this alloy in very aggressive environments of continuously aerated 0.1M and 1.0M sodium chloride (NaCl) solutions. Polarisation tests indicate that these compounds act as a cathodic inhibitors by reducing the rate of the oxygen reduction reaction, which results in a decreased corrosion current density and a separation of the corrosion potential from the pitting potential. This inhibition is thought to be due to the formation of a surface film consisting of rare earth metal oxide, aluminium oxide and a cerium-aluminium organo-phosphate complex. Surface analysis data from scanning electron microscopy and X-ray Energy Dispersive Spectroscopy show the complex nature of this protective film. This work further develops our understanding about the mechanisms through which these complex films form, and how inhibition occurs in the presence of these compounds.

Synthesis of single-crystalline LiFePO4 with rhombus-like morphology

In this investigation, carbon-coated LiFePO4 cathode materials were synthesized with a facile hydrothermal method. The structure and electrochemical properties of the materials were investigated by X-ray diffraction (XRD), Roman, transmission electron microscopy-energy dispersive spectroscopy (TEM-EDS), and electrochemical impedance spectroscopy (EIS). By adjusting the mixing concentration of starting materials, a single-crystalline LiFePO4 with an anisotropic rhombus morphology (Space Group: Pmnb No. 62) were successfully synthesized. In addition, the carbon coated on the surface of LiFePO4 material prepared has a lower ID/IG (0.80), which indicates an optimized carbon structure with an increased amount of sp2-type carbon. Electrochemical performance test shows that the carbon-coated LiFePO4 cathode materials have an initial discharge capacity of 146 mAh g−1 at 0.2C.