Effect of process variables on formation of dynamic strain induced ultrafine ferrite during hot torsion testing

Ultrafine grain sizes were produced using hot torsion testing of a 0.11C-1.68Mn-0.20Si (wt-%) steel, with ultrafine ferrite (<1 µm) nucleating intragranularly during testing by dynamic strain induced transformation. A systematic study was made of the effect of isothermal deformation temperature, strain level, strain rate, and accelerated cooling during deformation on the formation of ultrafine ferrite by this process. Decreasing the isothermal testing temperature below the Ae₃ temperature led to a greater driving force for ferrite nucleation and thus more extensive nucleation during testing; the formation of Widmanstätten ferrite prior to, or early during, deformation imposed a lower temperature limit. Increasing the strain above that where ferrite first began 0.8 at 675C and a strain rate of 3 s¯¹ increased the intragranular nucleation of ferrite. Strain rate appeared to have little effect on the amount of ferrite formed. However, slower strain rates led to extensive polygonisation of the ferrite formed because more time was available for ferrite recovery. Accelerated cooling during deformation followed by air cooling to room temperature led to a uniform microstructure consisting of very fine ferrite grains and fine spherical carbides located in the grain boundaries regions. Air cooling after isothermal testing led to carbide bands and a larger ferrite grain size.

Testing dynamic variance-sensitive foraging using individual differences in basal metabolic rates of zebra finches

Social foragers can alternate between searching for food (producer tactic), and searching for other individuals that have located food in order to join them (scrounger tactic). Both tactics yield equal rewards on average, but the rewards generated by producer are more variable. A dynamic variance-sensitive foraging model predicts that social foragers should increase their use of scrounger with increasing energy requirements and/or decreased food availability early in the foraging period. We tested whether natural variation in minimum energy requirements (basal metabolic rate or BMR) is associated with differences in the use of producer–scrounger foraging tactics in female zebra finches Taeniopygia guttata. As predicted by the dynamic variance-sensitive model, high BMR individuals had significantly greater use of the scrounger tactic compared with low BMR individuals. However, we observed no effect of food availability on tactic use, indicating that female zebra finches were not variance-sensitive foragers under our experimental conditions. This study is the first to report that variation in BMR within a species is associated with differences in foraging behaviour. BMR-related differences in scrounger tactic use are consistent with phenotype-dependent tactic use decisions. We suggest that BMR is correlated with another phenotypic trait which itself influences tactic use decisions.

Teaching organisational theory in undergraduate management programmes: an exercise in facilitated theory testing for active experimentation

This paper argues that there is an opportunity to improve the way that social science theory is taught by introducing an exercise in facilitated theory testing through active experimentation. This paper describes a learning experience that enables students to discover the dynamic nature of theoretical discoveries. This idea is grounded in the notion that students will gain much from learning about and testing theory experientially using real world data. A data based exercise is outlined and illustrated to reveal a learning experience that provides an opportunity to improve the way social science is taught by linking theory to empirical data. We argue that this provides an opportunity to offer a more holistic learning experience for theory teaching. The paper will be of special interest to those teaching theory in management, commerce, business and organisational studies courses. It will also be of interest to a more general audience because it provides a framework that can be modified whenever forging a connection between theory and 'the real world' is a primary learning objective.

Chromatic and luminance losses with multiple sclerosis and optic neuritis measured using dynamic random luminance contrast noise

We measured thresholds for detecting changes in colour and in luminance contrast in observers with multiple sclerosis (MS) and/or optic neuritis (ON) to determine whether reduced sensitivity occurs principally in red-green or blue-yellow second-stage chromatic channels or in an achromatic channel. Colour thresholds for the observers with MS/ON were higher in the red-green direction than in the blue-yellow direction, indicating greater levels of red-green loss than blue-yellow loss. Achromatic thresholds were raised less than either red-green or blue-yellow thresholds, showing less luminance-contrast loss than chromatic loss. With the MS/ON observers, blue-yellow and red-green thresholds were positively correlated but increasing impairment was associated with more rapid changes in red-green thresholds than blue-yellow thresholds. These findings indicate that demyelinating disease selectively reduces sensitivity to colour vision over luminance vision and red-green colours over blue-yellow colours.

The evolution of ultrafine ferrite formation through dynamic strain-induced transformation

Hot torsion testing of a C–Mn–V steel was used to study the evolution of  ultrafine ferrite (UFF) formation by dynamic strain-induced transformation (DSIT) in conjunction with air-cooling for two prior austenite grain sizes. This study evaluated not only the evolution of DSIT ferrite during straining, but also the grain growth behaviour of DSIT ferrite grains during post-deformation cooling. For both austenite grain sizes, the DSIT ferrite initially nucleated on/or near prior austenite grain boundaries at an early stage of transformation followed by the grain interiors. The prior austenite grain size affected the distribution of DSIT ferrite nucleation sites at an early stage of transformation and the subsequent coarsening behaviour of the grain boundary (GB) and the intragranular ferrite (IG) grains during post-deformation cooling. For the fine prior austenite grain size, the distribution of DSIT ferrite grains was more homogenous compared with the coarse austenite and the coarsening occurred not only in the GB ferrite grains but also in the IG ferrite grains. However, the ferrite coarsening mostly occurred for the IG ferrite rather than the GB ferrite grains in the coarse austenite. The result suggests that normal grain growth occurred during the overall transformation in the GB ferrite grains for the coarse initial austenite grain size.

Effect of thermomechanical parameters on the critical strain for ultrafine ferrite formation through hot torsion testing

A C–Mn–V steel was used to study ultrafine ferrite formation (1–3 μm) through dynamic strain-induced transformation (DSIT) using hot torsion experiments. A systematic study determined the critical strain for the start of DSIT (C,DSIT), although this may not lead to a fully ultrafine microstructure. Therefore, the strain to produce an ultrafine ferrite (UFF) as final microstructure (C,UFF) during deformation was also determined. In addition, the effect of thermomechanical parameters such as deformation temperature, prior austenite grain size, strain rate and cooling rate on C,DSIT and C,UFF has been evaluated. DSIT ferrite nucleated on prior austenite grain boundaries at an early stage of straining followed by intragranular nucleation at higher strains. The prior austenite grain size affected the distribution of DSIT ferrite nucleation sites at an early stage of transformation and the subsequent coarsening behaviour of the grain boundary and intragranular ferrite grains during post-deformation cooling. Also, C,DSIT and C,UFF increased with an increase in the prior austenite grain size and deformation temperature. The post-deformation cooling had a strong effect not only on C,UFF but also the UFF microstructure (i.e. final ferrite grain size and second phase characteristics).

Dynamic simulation of collisions of heavy high-speed trucks with concrete barriers

Real vehicle collision experiments on full-scale road safety barriers are important to determine the outcome of a vehicle versus barrier impact accident. However, such experiments require large investment of time and money. Numerical simulation has therefore been imperative as an alternative method for testing concrete barriers. In this research, spring subgrade models were first developed to simulate the ground boundary of concrete barriers. Both heavy trucks and concrete barriers were modeled using finite element methods (FEM) to simulate dynamic collision performances. Comparison of the results generated from computer simulations and on-site full-scale experiments demonstrated that the developed models could be applied to simulate the collision of heavy trucks with concrete barriers to provide the data to design new road safety barriers and analyze existing ones.

The production of ultrafine ferrite during hot torsion testing of a 0.11 Wt Pct C steel

Ultrafine ferrite grain sizes were produced in a 0.11C-1.6Mn-0.2Si steel by torsion testing isothermally at 675 °C after air cooling from 1250 °C. The ferrite was observed to form intragranularly beyond a von Mises equivalent tensile strain of approximately 0.7 to 0.8 and the number fraction of intragranular ferrite grains continued to increase as the strain level increased. Ferrite nucleated to form parallel and closely spaced linear arrays or “rafts” of many discrete ultrafine ferrite grains. It is shown that ferrite nucleates during deformation on defects developed within the austenite parallel to the macroscopic shear direction (i.e., dynamic strain-induced transformation). A model austenitic Ni-30Fe alloy was used to study the substructure developed in the austenite under similar test conditions as that used to induce intragranular ferrite in the steel. It is shown that the most prevalent features developed during testing are microbands. It is proposed that high-energy jogged regions surrounding intersecting microbands provide potential sites for ferrite nucleation at lower strains, while at higher strains, the walls of the microbands may also act as nucleation sites.

Characterization on ferrite microstructure evolution during large strain warm torsion testing of plain low carbon steel

Ferrite grain/subgrain structures evolution during the extended dynamic softening of a plain low carbon steel was investigated throughout the large strain warm deformation by hot torsion. Microstructural analysis with electron back-scattering diffraction (EBSD) scanning electron microscope (FEG/SEM) was carried out on the ferrite microstructural parameters. The results showed that the warm flow stress–strain curves are similar to those affected only by dynamic softening and an extended warm flow softening is seen during large strain deformation up to 30. Furthermore, with an increase in strain up to ~ vert, similar1 the grain size of ferrite, misorientation angle and fraction of high-angle boundaries gradually decrease and fraction of low-angle boundaries increases. With a further increase in the strain beyond ~, vert, similar2, these parameters remain approximately unchanged. No evidence of discontinuous dynamic recrystallisation involving nucleation and growth of new grains was found within ferrite. Therefore, the dynamic softening mechanism observed during large strain ferritic deformation is explained by continuous dynamic recrystallization (CDRX).

Realized volatility and correlation in grain futures markets: testing for spillover effects

Fluctuations in commodity prices are a major concern to many market participants. This paper uses realized volatility methods to calculate daily volatility and correlation estimates for three grain futures prices (corn, soybean, and wheat). The realized volatility estimates exhibit properties consistent with the stylized facts observed in earlier studies. According to daily realized correlations and regression coefficients, the spot returns from the three grain futures are positively related. The realized estimates are then used to evaluate the degree of volatility transmission across grain futures prices. The impulse response analysis is conducted by fitting the vector autoregressive model to realized volatility and correlation estimates, using the bootstrap method for statistical inference. The results indicate that rich dynamic interactions exist among the volatilities and correlations across the grain futures markets.

Dynamic recrystallization of austenite in Ni-30 Pct Fe model alloy : microstructure and texture evolution

The microstructure and crystallographic texture development in an austenitic Ni-30 pct Fe model alloy was investigated within the dynamic recrystallization (DRX) regime using hot torsion testing. The prominent DRX nucleation mechanism was strain-induced grain boundary migration accompanied by the formation of large-angle sub-boundaries and annealing twins. The increase in DRX volume fraction occurred through the formation of multiple twinning chains. With increasing strain, the pre-existing Σ3 twin boundaries became gradually converted to general boundaries capable of acting as potent DRX nucleation sites. The texture characteristics of deformed grains resulted from the preferred consumption of high Taylor factor components by new recrystallized grains. Similarly, the texture of DRX grains was dominated by low Taylor factor components as a result of their lower consumption rate during the DRX process. The substructure of deformed grains was characterized by “organized,” banded subgrain arrangements, while that of the DRX grains displayed “random,” more equiaxed subgrain/cell configurations.

The dynamic relationship between real exchange rates, real interest rates and foreign exchange reserves : empirical evidence from China

This article examines the long-run and short-run relationship between China's real exchange rate, foreign exchange reserves and the real interest rate differential between China and the United States using monthly data from 1980 to 2002. Extensive testing for unit roots allowing for up to two structural breaks in the trend indicates that the variables are not integrated of the same order. Thus, the bounds testing approach to cointegration is used, which finds that there is a single long-run relationship between the three variables. In the long run the real exchange rate has a statistically significant positive effect on foreign exchange reserves. The coefficient on the real interest rate differential is also positive, but is statistically insignificant. In the short-run it is found that the relationship between the real exchange rate, real interest rate differential and foreign exchange reserves is non-monotonic.

Texture and substructure characteristics of dynamic recrystallization in a Ni–30%Fe austenitic model alloy

The substructure and texture development during dynamic recrystallization (DRX) of an austenitic Ni–30%Fe model alloy was investigated using hot torsion testing. The current results revealed that the DRX texture was dominated by grains with a low Taylor factor component. This was related to the preferred nucleation and lower consumption rates of these grains during DRX. The substructure of DRX grains was ‘‘random” in character and displayed complex subgrain/cell arrangements that largely depended on grain orientation.

Robust correctness testing for digital forensic tools

In previous work, the authors presented a theoretical lower bound on the required number of testing runs for performance testing of digital forensic tools. We also demonstrated a practical method of testing showing how to tolerate both measurement and random errors in order to achieve results close to this bound. In this paper, we extend the previous work to the situation of correctness testing. The contribution of this methodology enables the tester to achieve correctness testing results of high quality from a manageable number of observations and in a dynamic but controllable way. This is of particular interest to forensic testers who do not have access to sophisticated equipment and who can allocate only a small amount of time to testing.

Robust performance testing for digital forensic tools

In previous work, the authors presented a theoretical lower bound on the required number of testing runs for performance testing of digital forensic tools. However, experimental errors are inevitable in laboratory settings, occurring as measurement errors or as random errors and can result in practical situations where the number of testing runs is far from the theoretical bound. This paper adapts our former work to tolerate such errors in the testing results. The contribution of our new methodology enables the tester to achieve performance testing results of high quality from a manageable number of observations and in a dynamic but controllable way. This is of particular interest to forensic testers who do not have access to sophisticated equipment and who can allocate only a small amount of time to testing.