A constitutive model of the deformation behaviour of twinning induced plasticity (TWIP) steel at different temperatures

The mechanical behaviour of Fe-18Mn-0.6C-1Al (wt%) TWIP steel was modelled in the temperature range from room temperature to 400°C. The proposed constitutive model was based on the Kocks-Mecking-Estrin (KME) model. The model parameters were determined using extensive experimental measurements of the physical parameters such as the dislocation mean free path and the volume fraction of twinned grains. More than 100 grains with a total area of ~300μm2 were examined at different strain levels over the entire stress-strain curve. Uniaxial tensile deformation of the TWIP steel was modelled for different deformation temperatures using a modelling approach which considers two distinct populations of grains: twinned and twin-free ones. A key point of the work was a meticulous experimental determination of the evolution of the volume fraction of twinned grains during uniaxial tensile deformation. This information was implemented in a phase-mixture model that yielded a very good agreement with the experimental tensile behaviour for the tested range of deformation temperatures. © 2014 Elsevier B.V.

The correlation between stacking fault energy and the work hardening behaviour of high-mn twinning induced plasticity steel tested at various temperatures

High-Mn Twinning Induced Plasticity (TWIP) steels have superior mechanical properties, which make them promising materials in automotive industry to improve the passenger safety and the fuel consumption. The TWIP steels are characterized by high work hardening rates due to continuous mechanical twin formation during the deformation. Mechanical twinning is a unique deformation mode, which is highly governed by the stacking fault energy (SFE). The composition of steel alloy was Fe-18Mn-0.6C-1Al (wt.%) with SFE of about 25-30 mJ/m2 at room temperature. The SFE ensures the mechanical twinning to be the main deformation mechanism at room temperature. The microstructure, mechanical properties, work hardening behaviour and SFE of the steel was studied at the temperature range of ambient ≤T[°C]≤ 400°C. The mechanical properties were determined using Instron tensile testing machine with 30kN load cell and strain rate of 10-3s-1 and the work hardening behaviour curves were generated using true stress and true strain data. The microstructure after deformation at different temperatures was examined using Zeiss Supra 55VP SEM. It was found that an increase in the deformation temperature raised the SFE resulting in the deterioration of the mechanical twinning that led to decrease not only in the strength but also in the total strain of the steel. A correlation between the temperature, the SFE, the mechanical twinning, the mechanical properties and the work hardening rate was also found. © (2014) Trans Tech Publications, Switzerland.

The influence of temperature on the forming behavior of metal/polymer laminates in sheet metal forming

The influence of temperature on the forming behavior of an aluminum/polypropylene/aluminum (APA) sandwich sheet was studied. Shear and tensile tests were performed to determine the mechanical properties of the laminate and the component materials as a function of process temperature. The forming limit diagram (FLD) of the laminate was established for two different temperatures, and its springback behavior was examined in four-point bend and channel bend tests. Cup forming tests were performed at various test temperatures to determine the limiting drawing ratio (LDR) and the tendency for wrinkling at these temperatures. Although there was only a minor influence of temperature on the mechanical properties and the FLD values of the laminate, the bend test results reveal that springback can be reduced by forming at higher temperature. The decreasing strength of the core material with rising process temperature led to an increased tendency of the laminate to wrinkle in the heated cup drawing tests.

Texture changes during uniaxial compression of Mg-3AI-1Zn

The mechanical anisotropy of wrought Mg alloys is very high. For example the yield stress of extruded Mg-3Al-1Zn tested in tension can be as high as twice that obtained in compression [1]. To solve the problems this creates for product design it is necessary to understand the sensitivity of texture to processing parameters. Uniaxial compression tests at different temperatures were performed on cylindrical samples of an extruded Mg-3Al-1Zn bar. The texture
during this deformation changes from a situation where all crystal c-axes are nearly perpendicular to the sample axis to one where the c-axes are all nearly parallel to this axis. Compression was stopped at different strains to examine the rate of this texture change. Textures were examined using EBSD measurements. It was found that different mechanisms operate depending on the temperature of deformation and that a variety of textures can be created. Also it was seen that an annealing treatment performed after compression has an influence on the texture. Afterwards the samples were subjected to another uniaxial compression test to examine the influence of texture on room temperature properties.

Effects of laundering on conductivity of polypyrrole-coated textiles

This study examines the resistance change in conductive polypyrrole-coated PET fabrics under the AS 2001.4.15 – 1994 laundering test conditions. The effects of individual detergent components of a standard detergent, including auxiliary chemicals, at four different temperatures were studied. When the coated fabric was washed under the AS 2001.4.15-1994 conditions, the ECE reference detergent and pure soap flakes (sodium sterate) both decreased the conductivity of the coating at a rate exponentially proportional to the laundering temperature. Detergent types had an influence over the rate of degradation; pH conditions had a large influence on the rate of polymer deterioration with the acidic nonionic detergent giving rise to significantly improved laundering conditions. The auxiliary chemicals, sodium carbonate and sodium perborate were seen to cause large degradation of polymers during laundering. Ethylene diamine tetra acetic acid was seen to have only a slight influence on the reduction of conductivity of polymers.

Within-population variation in ejaculate characteristics in a prolonged breeder, Peron's tree frog, Litoria peronii

Sperm number is often a good predictor of success in sperm competition; however, it has become increasingly clear that, for some species, variation in probability of paternity cannot be explained by sperm number alone. Intraspecific variation in ejaculate characteristics, such as the number of viable sperm and sperm longevity, may play an equally important role in determining fertilization success. Here, we assess variation among ejaculates in three factors that may contribute to fertilization success (number of sperm per ejaculate, viability, and longevity), in a population of Peron’s tree frog (Litoria peronii). We detected large variation among males in the number of sperm per ejaculate and the proportion of viable sperm within ejaculates, which could not be explained by variation in either male size or body condition. However, the proportion of viable sperm released by males increased over the season. Finally, we assessed sperm longevity (proportion viable sperm determined using a dual-fluorochrome vital dye) at two different temperatures. At 23°C, on average, 75% of sperm remained viable after 2 h, but there were significant differences amongst males with the percentage of viable sperm ranging from 43% to 95%. For sperm incubated at 4°C, ejaculates varied fivefold in sperm longevity with some males having 50% viable sperm after 5 days. Our data suggest that ejaculate characteristics (sperm number, viability, and longevity) vary widely in Peron’s tree frog and may therefore play an important role in determining siring success both in the presence and absence of sperm competition. We discuss the results in relation to selection on ejaculate traits via natural and sexual selection in this and other amphibians.

Titanium oxide nanorods extracted from ilmenite sands

One dimensional titanium oxides (TiO2) nanorods and nanowires have substantial applications in photocatalytic, nanoelectronic, and photoelectrochemical areas. These applications require large quantities of materials and a production technique suitable for future industry fabrication. We demonstrate here a new method for mass production of TiO2 nanorods from mineral ilmenite sands (FeTiO3). In this process, powder mixtures of ilmenite and activated carbon were first ball milled; the milled samples were then heated twice at two different temperatures. First high-temperature annealing produced metastable titanium oxide phases, and subsequent second low-temperature annealing in N2-5%H2 activates the growth of rutile nanorods. This solid-state growth process allows large-quantity production of rutile nanorods.

Potential application of solid electrolyte P11 OH in Ni/MH batteries

N,N-Dimethylpyrrolidoium hydroxide (P11 OH) with polymer poly(tetramethyl ammonium acrylate) (PTMA) was investigated as an electrolyte in Ni/MH cells in this work. The efficiency and the performance of the electrolyte was discussed and elucidated with the performance of the cell. Their electrochemical characteristics had been investigated at different temperatures (25 °C and 50 °C) and different discharge current (15 mA g⁻¹ and 30 mA g⁻¹). The results show that the cell with electrolyte polymer-P11OH is dischargeable at these two temperatures, and a discharge capacity of 142 mAh g⁻¹ at 25 °C has been obtained.

Morphology evolution during annealing and electrical conductivity of titania nanotube films

Titania nanotube films were produced by anodization of titanium foil. The titania nanotube films were annealed at different temperatures. Morphology evolution, phase transformation and electrical conductivity of the titania nanotubes were studied. Results showed that the nanotube walls became rough, porous and even collapsed after annealed at 400, 500 and 600°C respectively. Titania anatase phase formed after annealed at 400°C; the amount of anatase phase increased as the annealing temperature increased. The conductivity of the nanotube film annealed at 400°C was improved greatly compared with the conductivity of the as-anodized nanotube film. However, the conductivity of the nanotube films annealed at higher temperatures decreased. The effect of the morphology on the electronic conductivity of the titania nanotube films was discussed.

Solute segregation and texture modification in an extruded magnesium alloy containing gadolinium

The alloy Mg-1.5Gd has been extruded at different temperatures to produce two significantly different textures. At lower extrusion temperatures there was significant solute clustering in the matrix, coupled with segregation of solute to the grain boundaries. At higher temperatures these two phenomena were both less pronounced. It is suggested here that segregation of solute to the grain boundaries plays a significant role in the texture modification effect that rare earth elements have in magnesium alloys.

Effect of temperature on anaerobic fermentation of banana stem residue

Anaerobic fermentation experiments were conducted on banana (pseudo) stem residue to study the relationship between fermentation temperature and gas production yield and gas production rate, and methane content. Based on fixed dry matter concentration, inoculum concentration and fermentation time, different temperatures, i.e. 25, 30, 35, 40°C were selected and formed four experimental groups. Four levels of single factor tests were conducted to optimize temperature parameter for anaerobic fermentation of banana stem residue. The results showed that the daily gas yield of banana stem residue reached the maximum value of 36.8L on the fourth day at 35°C, and the average gas yield was 5.03L/d. The total gas yield was 402.3L, while the maximum methane content was 61.2% in the whole fermentation process. The results indicated that the comprehensive effect was best at 35°C in anaerobic fermentation of banana stem residue.

Novel carbon materials for thermal energy harvesting

To decrease the consumption of fossil fuels, research has been done on utilizing low grade heat, sourced from industrial waste streams. One promising thermoenergy conversion system is a thermogalvanic cell; it consists of two identical electrodes held at different temperatures that are placed in contact with a redox-based electrolyte [1, 2]. The temperature dependence of the direction of redox reactions allows power to be extracted from the cell [3, 4]. This study aims to increase the power conversion efficiency and reduce the cost of thermogalvanic cells by optimizing the electrolyte and utilizing a carbon based electromaterial, reduced graphene oxide, as electrodes. Thermal conductivity measurements of the K3Fe(CN)6/K4Fe(CN)6 solutions used, indicate that the thermal conductivity decreases from 0.591 to 0.547 W/m K as the concentration is increased from 0.1 to 0.4 M. The lower thermal conductivity allowed a larger temperature gradient to be maintained in the cell. Increasing the electrolyte concentration also resulted in higher power densities, brought about by a decrease in the ohmic overpotential of the cell, which allowed higher values of short circuit current to be generated. The concentration of 0.4 MK3Fe(CN)6/K4Fe(CN)6 is optimal for thermal harvesting applications using R-GO electrodes due to the synergistic effect of the reduction in thermal flux across the cell and the enhancement of power output, on the overall power conversion efficiency. The maximum mass power density obtained using R-GO electrodes was 25.51 W/kg (three orders of magnitude higher than platinum) at a temperature difference of 60 _C and a K3Fe(CN)6/K4Fe(CN)6 concentration of 0.4 M.

Enhancing bi-functional electrocatalytic activity of perovskite by temperature shock : a case study of LaNiO3-ᵟ

Perovskite oxide offers an attractive alternative to precious metal electrocatalysts given its low cost and high oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) activity. The results obtained in this work suggest a correlation of crystal structure with ORR and OER activity for LaNiO3-?. LaNiO3-? perovskites with different crystal structure were obtained by heating at different temperatures, e.g., 400, 600, and 800 C followed by quenching into room temperature. Cubic structure (relative to rhombohedral) leads to higher ORR and OER activity as well as enhanced bi-functional electrocatalytic activity, e.g., lower difference in potential between the ORR at -3 mA cm-2 and OER at 5 mA cm -2 (?E). Therefore, this work shows the possibility to adjust bi-functional activity through a simple process. This correlation may also extend to other perovskite oxide systems.

Recrystallization kinetic behavior of copper-bearing strip cast steel

In the present study, copper-bearing low carbon steels were produced by direct strip casting (DSC) method on a pilot scale. The effects of copper on mechanical, microstructural, and recrystallization behavior were investigated. As-cast microstructure mainly consists of polygonal ferrite and Widmanstatten ferrite. The increase in Cu increases the amount of Widmanstatten ferrite and induces the formation of bainite in the as-cast condition. It was found that copper increases strength and hardness by solid solution strengthening, grain refinement, and precipitation hardening and the increment is significant above 1% Cu in as-cast condition. Six different compositions were selected for recrystallization study. All the samples were cold rolled to 70% reduction and annealed at three different temperatures, 600, 650, and 700°C for various times. Recrystallization responses were strongly dependent on initial microstructure and Cu content and the effect is dramatic between 1 and 2% Cu. Recrystallization time and temperature were found to be increased with increase in copper content.

Temperature-dependence of mechanical properties of open-cell titanium foam

An open-cell titanium foam with relative density of 0.2 was prepared by powder metallurgical process. The compressive mechanical properties of the foam at the different temperatures in the range of 20-600°C were measured and the temperature-dependence of its mechanical properties was discussed. The results indicate that the foam material exhibit fragile fracture characteristic at room temperature. When it is deformed over 200°C, the stress-strain curves exhibit plastic deformation characteristic, including three distinct regions: the linear elasticity region, the plastic collapse region, and the densification region. The Young's modulus, yield stress and elastic limit decrease with increasing of temperature. The temperature-dependence of these properties can be expressed as E*=1.5217 × 10 9-5.988 × 10 5T, σ cl*=85.7-0.095T, σ ys*=99.1-0.167V7.02 × 10 -5T 2 respectively.