Controlled growth of zinc nanowires

Zinc nanowires have been synthesized by heating a mixture of boron and zinc oxide (ZnO) powders at 1050 °C under a nitrogen atmosphere. The influences of the gas flow rate and the substrate character on the nanowire formation were investigated. It was found that higher-flow rate of gas led to the formation of thinner nanowires; while lower-flow rate of gas produced thicker nanowires and even particles due to the higher partial pressure of Zn vapor in this case. Zn nanowires can be produced on alumina and quartz substrates, but not on a stainless-steel substrate under the same or different synthetic conditions. Photoluminescence measurements were conducted on Zn nanowires and particles and weak emission bands at 482 and 493 nm were observed, which may be contributed by the thin ZnO film on the nanowire surface.

Thermodynamics approach to the hydrogen diffusion and phase transformation in titanium particles

The hydrogen diffusion and phase transformation in a titanium particle were studied based on thermodynamic calculation. The mechanisms of hydrogen diffusion in different phases (alpha-Ti, beta-Ti and TiHx) were analyzed. A mobility database was developed for titanium– hydrogen system based on the experimental works on hydrogen diffusion coefficient reported in literature and the fundamental of diffusion. To implement the calculation, a commercial software package for the simulation of diffusion-controlled phase transformation was used. The hydrogen diffusion process, hydrogen distribution, phase transformation and phase growth rate during hydrogenization of a titanium particle at temperatures of 560 K, 800K and 1000K were discussed. The thermodynamics and kinetics analysis provided quantitative insight into the diffusion process and improved the understanding of diffusion mechanism and phase transformation.

Investigation on decomposition behavior of austenite under continuous cooling in vanadium microalloyed steel (30MSV6)

In the present study, investigations are focused on microstructural evolution and the resulting hardness during continuous cooling transformation (CCT) in a commercial vanadium microalloyed steel (30MSV6). Furthermore, the effects of cooling rate and austenite grain size (AGS) on CCT behavior of the steel have been studied by employing high-resolution dilatometry. Quantitative metallography accompanied with scanning electron microscopy (SEM) has efficiently confirmed the dilatometric measurements of transformation kinetics and austenite decomposition products. A semi-empirical model has been proposed for prediction of microstructural development during austenite decomposition of the steel and the resultant hardness. The model consists of 8 sub-models including ferrite transformation start temperature, ferrite growth, pearlite start temperature, pearlite growth, bainite start temperature, bainite growth, martensite start temperature and hardness. The transformed fractions of ferrite, pearlite and bainite have been described using semi-empirical Johnson-Mehl-Avrami-Kolmogorov (JMAK) approach in combination with Scheil's equation of additivity. The JMAK rate parameter for bainite has been formulated using a diffusion-controlled model. Predictions of the proposed model were found to be in close agreement with the experimental measurements.

Structure effect on the oxygen permeation properties of barium bismuth iron oxide membranes

In this work, we investigated the oxygen permeation properties of barium bismuth iron oxide within the family of [Ba_2−3xBi_3x−1][Fe_2xBi_1−2x]O_2+3x/2 for x = 0.17–0.60. The structure changed progressively from cubic to tetragonal and then to hexagonal as function of x in accordance with the different relative amounts of bismuth on A-site and B-site of ABO_3−δ perovskite lattices. We found that the oxygen flux and electrical conductivity correlated strongly, and it was prevalent for the cubic structure (x = 0.33–0.40) which conferred the highest oxygen flux of 0.59 ml min⁻¹ cm⁻² at 950 °C for a disk membrane x = 0.33 with a thickness of 1.2 mm. By reducing the thickness of the disk membrane to 0.8 mm, the oxygen flux increased to 0.77 ml min⁻¹ cm⁻², suggesting both surface kinetics and ion diffusion controlled oxygen flux, though the former was more prominent at higher temperatures. For disk membranes x = 0.45–0.60, the perovskite structure changed to tetragonal and hexagonal, and the oxygen flux was insignificant below 900 °C, clearly indicating electron conduction properties only. However, for two compositions with relatively high bismuth content, e.g. x = 0.55 and 0.60, there was a sudden and significant rise of oxygen permeability above 900 °C, by more than one order of magnitude. These materials changed conduction behavior from metallic to semiconductor at around 900 °C. These results suggest the advent of mixed ionic electronic conducting properties caused by the structure transition as bismuth ions changed their valence states to compensate for the oxygen vacancies formed within the perovskite lattices.

Electrochemical method for studying localized corrosion beneath disbonded coatings under cathodic protection

This paper presents a new method for measuring localized corrosion under disbonded coatings by means of an electrochemical sensor, denoted differential aeration sensor (DAS). It measures the distribution of electrochemical currents over an electrode array surface partially covered by a crevice that simulates a disbonded coating. The DAS has been evaluated using immersion tests at open circuit and under cathodic protection (CP) conditions. Under both conditions, anodic as well as cathodic current densities were detected within the crevice. A fundamental understanding for the detection of anodic currents under CP has been explained in terms of basic electrochemistry. Based on the current distribution data provided by the sensor, two different analysis methods have been used to estimate corrosion and its distribution. These methods consisted of a direct application of Faraday's Law to the anodic currents detected by the array, and on a sensor-specific method denoted corrected currents' method. It has been demonstrated that under diffusion controlled conditions this latter method produces a better corrosion estimation than the direct application of Faraday's Law. The corrected currents' method allowed the estimation of corrosion patterns outside the crevice under CP. Good correlation between electrochemical calculations and surface profilometry results has been obtained.

Aqueous peptide-TiO2 interfaces: isoenergetic binding via either entropically or enthalpically driven mechanisms

A major barrier to the systematic improvement of biomimetic peptide-mediated strategies for the controlled growth of inorganic nanomaterials in environmentally benign conditions lies in the lack of clear conceptual connections between the sequence of the peptide and its surface binding affinity, with binding being facilitated by noncovalent interactions. Peptide conformation, both in the adsorbed and in the nonadsorbed state, is the key relationship that connects peptide-materials binding with peptide sequence. Here, we combine experimental peptide-titania binding characterization with state-of-the-art conformational sampling via molecular simulations to elucidate these structure/binding relationships for two very different titania-binding peptide sequences. The two sequences (Ti-1, QPYLFATDSLIK; Ti-2, GHTHYHAVRTQT) differ in their overall hydropathy, yet via quartz-crystal microbalance measurements and predictions from molecular simulations, we show these sequences both support very similar, strong titania-binding affinities. Our molecular simulations reveal that the two sequences exhibit profoundly different modes of surface binding, with Ti-1 acting as an entropically driven binder while Ti-2 behaves as an enthalpically driven binder. The integrated approach presented here provides a rational basis for peptide sequence engineering to achieve the in situ growth and organization of titania nanostructures in aqueous media and for the design of sequences suitable for a range of technological applications that involve the interface between titania and biomolecules.

Regional specificity of exercise and calcium during skeletal growth in girls: a randomized controlled trial

Combining exercise with calcium supplementation may produce additive or multiplicative effects at loaded sites; thus, we conducted a single blind, prospective, randomized controlled study in pre- and early-pubertal girls to test the following hypotheses. (1) At the loaded sites, exercise and calcium will produce greater benefits than exercise or calcium alone. (2) At non-loaded sites, exercise will have no benefit, whereas calcium with or without exercise will increase bone mass over that in exercise alone or no intervention. Sixty-six girls aged 8.8 ± 0.1 years were randomly assigned to one of four study groups: moderate-impact exercise with or without calcium or low-impact exercise with or without calcium. All participants exercised for 20 minutes, three times a week and received Ca-fortified (434 ± 19 mg/day) or non-fortified foods for 8.5 months. Analysis of covariance (ANCOVA) was used to determine interaction and main effects for exercise and calcium on bone mass after adjusting for baseline bone mineral content and growth in limb lengths. An exercise-calcium interaction was detected at the femur (7.1%, p < 0.05). In contrast, there was no exercise-calcium interaction detected at the tibia-fibula; however, there was a main effect of exercise: bone mineral content increased 3% more in the exercise than non-exercise groups (p < 0.05). Bone mineral content increased 2-4% more in the calcium-supplemented groups than the non-supplemented groups at the humerus (12.0% vs. 9.8%, respectively, p < 0.09) and radius-ulna (12.6% vs. 8.6%, respectively, p < 0.01). In conclusion, greater gains in bone mass at loaded sites may be achieved when short bouts of moderate exercise are combined with increased dietary calcium, the former conferring region-specific effects and the latter producing generalized effects.

Drug release rate and anti-microbial effect of controlled-diffusion biopolymer membranes

In this study, a series of fibrous membranes made from cellulose acetate (CA) and polyester urethane (PEU) by co-electrospining or blend-electrospining were evaluated for drug release kinetics, in vitro anti-microbial activity and in vivo would healing performance when used as wound dressings. To stop common clinical infections, an antibacterial agent, Polyhexamethylene Biguanide (PHMB) was incorporated into e-spun fibres. The presence of CA in the wound healing membrane was found to improve hydrophilicity and permeability to air and moisture. The in vivo tests indicated that the addition of PHMB and CA considerably improved the wound healing efficiency. CA fibres became slightly swollen upon contacting with the wound exudates. It can not only speed up the liquid evaporation but also create a moisture environment for wound recovery. The drug release dynamics of membranes was controlled by the structure of membranes and component rations within membranes. The lower ration of CA:PEU retained the sound mechanical properties of membranes, and also reduced the boost release effectively and slowed down diffusion of antibacterial agent during in vitro tests. The controlled-diffusion membranes exert long-term anti-infective effect.

Teledermatology: The Case of Adoption and Diffusion of Telemedicine Health Waikato in New Zealand

Telemedicine emerged as a possible solution to New Zealand health providers in reaching out to rural patients, by offering medical services and conducting administrative meetings and training. However, despite the rapid growth and high visibility of these projects in countries like the United States, relatively few patients are now being seen through telemedicine. Accordingly, this research attempts to investigate telemedicine's effectiveness in New Zealand by using a theoretical framework. Thus, the purpose of this paper is to explain factors influencing the adoption and diffusion of telemedicine utilising the video conferencing technology (TMVC) for dermatology within Health Waikato Ltd. (HW).

Exercise and calcium combined results in a Greater osteogenic effect than either factor alone: a blinded randomized placebo-controlled trial in boys

We examined the combined effects of exercise and calcium on BMC accrual in pre- and early-pubertal boys. Exercise and calcium together resulted in a 2% greater increase in femur BMC than either factor alone and a 3% greater increase in BMC at the tibia–fibula compared with the placebo group. Increasing dietary calcium seems to be important for optimizing the osteogenic effects of exercise.

Introduction: Understanding the relationship between exercise and calcium during growth is important given that the greatest benefits derived from these factors are achieved during the first two decades of life. We conducted a blinded randomized-controlled exercise–calcium intervention in pre- and early-pubertal boys to test the following hypotheses. (1) At the loaded sites (femur and tibia–fibula), exercise and calcium will produce greater skeletal benefits than either exercise or calcium alone. (2) At nonloaded sites (humerus and radius–ulna), there will be an effect of calcium supplementation.

Materials and Methods: Eighty-eight pre- and early-pubertal boys were randomly assigned to one of four study groups: moderate impact exercise with or without calcium (Ca) (Ex + Ca and Ex + placebo, respectively) or low impact exercise with or without Ca (No-Ex + Ca and No-Ex + Placebo, respectively). The intervention involved 20 minutes of either moderate- or low-impact exercise performed three times a week and/or the addition of Ca-fortified foods using milk minerals (392 ± 29 mg/day) or nonfortified foods over 8.5 months. Analysis of covariance was used to determine the main and combined effects of exercise and calcium on BMC after adjusting for baseline BMC.

Results: At baseline, no differences were reported between the groups for height, weight, BMC, or bone length. The increase in femur BMC in the Ex + Ca group was 2% greater than the increase in the Ex + placebo, No-Ex + Ca, or No-Ex + Placebo groups (all p < 0.03). At the tibia–fibula, the increase in BMC in the Ex + Ca group was 3% greater than the No-Ex + placebo group (p < 0.02) and 2% greater than the Ex + Placebo and the No-Ex + Ca groups (not significant). No effect of any group was detected at the humerus, ulna–radius, or lumbar spine for BMC, height, bone area, or volume.

Conclusions: In this group of normally active boys with adequate calcium intakes, additional exercise and calcium supplementation resulted in a 2–3% greater increase in BMC than controls at the loaded sites. These findings strengthen the evidence base for public health campaigns to address both exercise and dietary changes in children for optimizing the attainment of peak BMC.

The evidence that exercise during growth or adulthood reduces the risk of fragility fractures is weak

There has never been, and will never be, a randomized double-blind placebo-controlled trial demonstrating that exercise in youth, adulthood or old age reduces fragility or osteoporosis-related fractures in old age. The next level of evidence, a randomized, controlled but unblinded study with fractures as an end-point is feasible but has never been done. The basis for the belief that exercise reduces fractures is derived from lower levels of ‘evidence’, namely, retrospective and prospective observation cohort studies and case–control studies. These studies are at best hypothesis generating, never hypothesis testing. They are all subject to many systematic biases and should be interpreted with extreme scepticism. Surrogate measures of anti-fracture efficacy are the next level of evidence, such as the demonstration of a reduction in risk factors for falls, a reduction in falls, a reduction in fractures due to falls, an increase in peak bone size and mass, prevention of bone loss in midlife and restoration of bone mass and structure in old age.

Growth and survival rates of large-type sporophytes of Ecklonia cava transplanted to a growth environment with small-type sporophytes

Stipe lengths of sporophytes of Ecklonia cava Kjellman have been reported to be longer along the southeast than southwest coast of the Izu Peninsula, central Japan. Two bays in this region that have natural populations of E. cava, but with different stipe lengths, were chosen for transplant experiments to examine if stipe length was an environmentally controlled trait. Transplant experiments were carried out in order to determine whether large-type sporophytes of E. cava with long stipes growing in Nabeta Bay (southeast Izu Peninsula, Japan) would turn into small-type sporophytes with short stipes when transplanted to Nakagi Bay (southwest Izu Peninsula). Ten juvenile sporophytes of E. cava (stipe length < 5 cm) were collected from Nabeta Bay (large-type habitat) and transplanted to Nakagi Bay (short-type habitat) in December 1995. As a transplant control, ten juvenile sporophytes of E. cava growing in Nakagi Bay were also transplanted to the same artificial reefs. Growth and survival rates of the sporophytes were monitored monthly for 3 y until December 1998. The transplanted sporophytes showed an increase in their stipe length and diameter from winter to spring, whereas almost no increase was observed from summer to autumn. However, the elongation was greater in Nabeta sporophytes than in Nakagi sporophytes. The primary blade length increased mainly from winter to early spring and decreased largely in autumn. Average primary blade lengths were similar in both Nabeta and Nakagi sporophytes from the end of the first year of transplanting. Although ca. 70% of both Nabeta and Nakagi sporophytes survived during the first 2 y after transplantation, no Nakagi sporophytes and only two Nabeta sporophytes survived to the end of the 3 y study period. Despite transplantation to Nakagi Bay, where short sitpes are naturally present, the sporophytes from Nabeta Bay persisted in having longer stipes, which suggests that stipe length is genetically, rather than environmentally, controlled.

Focused ion beam milling as a universal template technique for patterned growth of carbon nanotubes

Focused ion beam (FIB) milling system has been used to create nanosized patterns as the template for patterned growth of carbon nanotubes on Si substrate surface without predeposition of metal catalysts. Carbon nanotubes only nucleate and grow on the template under controlled pyrolysis of iron phthalocyanine at 1000 °C. The size, growth direction, and density of the patterned nanotubes can be controlled under different growth conditions and template sizes. Atomic force microscopy and electron microscopy analyses reveal that the selective growth on the FIB template is due to its special surface morphology and crystalline structure.

Growth and structure of prismatic boron nitride nanorods

Prismatic boron nitride nanorods have been grown on single crystal silicon substrates by mechanical ball-milling followed by annealing at 1300 °C. Growth takes place by rapid surface diffusion of BN molecules, and follows heterogeneous nucleation at catalytic particles of an Fe/Si alloy. Lattice imaging transmission electron microscopy studies reveal a central axial row of rather small truncated pyramidal nanovoids on each nanorod, surrounded by three basal planar BN domains which, with successive deposition of epitaxial layers adapt to the void geometry by crystallographic faceting. The bulk strain in the nanorods is taken up by the presence of what appear to be simple nanostacking faults in the external, near-surface domains which, like the nanovoids are regularly repetitive along the nanorod length. Growth terminates with a clear cuneiform tip for each nanorod. Lateral nanorod dimensions are essentially determined by the size of the catalytic particle, which remains as a foundation essentially responsible for base growth. Growth, structure, and dominating facets are shown to be consistent with a system which seeks lowest bulk and surface energies according to the well-known thermodynamics of the capillarity of solids.