Application of multi-criteria decision making methods to compression ignition engine efficiency and gaseous, particulate and greenhouse gas emissions

Compression ignition (CI) engine design is subject to many constraints which presents a multi-criteria optimisation problem that the engine researcher must solve. In particular, the modern CI engine must not only be efficient, but must also deliver low gaseous, particulate and life cycle greenhouse gas emissions so that its impact on urban air quality, human health, and global warming are minimised. Consequently, this study undertakes a multi-criteria analysis which seeks to identify alternative fuels, injection technologies and combustion strategies that could potentially satisfy these CI engine design constraints. Three datasets are analysed with the Preference Ranking Organization Method for Enrichment Evaluations and Geometrical Analysis for Interactive Aid (PROMETHEE-GAIA) algorithm to explore the impact of 1): an ethanol fumigation system, 2): alternative fuels (20 % biodiesel and synthetic diesel) and alternative injection technologies (mechanical direct injection and common rail injection), and 3): various biodiesel fuels made from 3 feedstocks (i.e. soy, tallow, and canola) tested at several blend percentages (20-100 %) on the resulting emissions and efficiency profile of the various test engines. The results show that moderate ethanol substitutions (~20 % by energy) at moderate load, high percentage soy blends (60-100 %), and alternative fuels (biodiesel and synthetic diesel) provide an efficiency and emissions profile that yields the most “preferred” solutions to this multi-criteria engine design problem. Further research is, however, required to reduce Reactive Oxygen Species (ROS) emissions with alternative fuels, and to deliver technologies that do not significantly reduce the median diameter of particle emissions.

The influence of fatty acid methyl ester profiles on inter-cycle variability in a heavy duty compression ignition engine

With the advent of alternative fuels, such as biodiesels and related blends, it is important to develop an understanding of their effects on inter-cycle variability which, in turn, influences engine performance as well as its emission. Using four methanol trans-esterified biomass fuels of differing carbon chain length and degree of unsaturation, this paper provides insight into the effect that alternative fuels have on inter-cycle variability. The experiments were conducted with a heavy-duty Cummins, turbo-charged, common-rail compression ignition engine. Combustion performance is reported in terms of the following key in-cylinder parameters: indicated mean effective pressure (IMEP), net heat release rate (NHRR), standard deviation of variability (StDev), coefficient of variation (CoV), peak pressure, peak pressure timing and maximum rate of pressure rise. A link is also established between the cyclic variability and oxygen ratio, which is a good indicator of stoichiometry. The results show that the fatty acid structures did not have a significant effect on injection timing, injection duration, injection pressure, StDev of IMEP, or the timing of peak motoring and combustion pressures. However, a significant effect was noted on the premixed and diffusion combustion proportions, combustion peak pressure and maximum rate of pressure rise. Additionally, the boost pressure, IMEP and combustion peak pressure were found to be directly correlated to the oxygen ratio. The emission of particles positively correlates with oxygen content in the fuel as well as in the air-fuel mixture resulting in a higher total number of particles per unit of mass.

Performance and gaseous and particle emissions from a liquefied petroleum gas (LPG) fumigated compression ignition engine

In this study, an LPG fumigation system was fitted to a Euro III compression ignition (CI) engine to explore its impact on performance, and gaseous and particulate emissions. LPG was introduced to the intake air stream (as a secondary fuel) by using a low pressure fuel injector situated upstream of the turbocharger. LPG substitutions were test mode dependent, but varied in the range of 14-29% by energy. The engine was tested over a 5 point test cycle using ultra low sulphur diesel (ULSD), and a low and high LPG substitution at each test mode. The results show that LPG fumigation coerces the combustion into pre-mixed mode, as increases in the peak combustion pressure (and the rate of pressure rise) were observed in most tests. The emissions results show decreases in nitric oxide (NO) and particulate matter (PM2.5) emissions; however, very significant increases in carbon monoxide (CO) and hydrocarbon (HC) emissions were observed. A more detailed investigation of the particulate emissions showed that the number of particles emitted was reduced with LPG fumigation at all test settings – apart from mode 6 of the ECE R49 test cycle. Furthermore, the particles emitted generally had a slightly larger median diameter with LPG fumigation, and had a smaller semi-volatile fraction relative to ULSD. Overall, the results show that with some modifications, LPG fumigation systems could be used to extend ULSD supplies without adversely impacting on engine performance and emissions.

A statistical model for combustion resonance from a DI diesel engine with applications

Introduced in this paper is a Bayesian model for isolating the resonant frequency from combustion chamber resonance. The model shown in this paper focused on characterising the initial rise in the resonant frequency to investigate the rise of in-cylinder bulk temperature associated with combustion. By resolving the model parameters, it is possible to determine: the start of pre-mixed combustion, the start of diffusion combustion, the initial resonant frequency, the resonant frequency as a function of crank angle, the in-cylinder bulk temperature as a function of crank angle and the trapped mass as a function of crank angle. The Bayesian method allows for individual cycles to be examined without cycle-averaging|allowing inter-cycle variability studies. Results are shown for a turbo-charged, common-rail compression ignition engine run at 2000 rpm and full load.

The effect of triacetin as a fuel additive to waste cooking biodiesel on engine performance and exhaust emissions

This study investigates the effect of oxygenated fuels on engine performance and exhaust emission under a custom cycle using a fully instrumented 6-cylinder turbocharged diesel engine with a common railinjection system. A range of oxygenated fuels based on waste cooking biodiesel with triacetin as an oxygenated additive were studied. The oxygen ratio was used instead of the equivalence ratio, or air to fuelratio, to better explain the phenomena observed during combustion. It was found that the increased oxygen ratio was associated with an increase in the friction mean effective pressure, brake specific fuel consumption, CO, HC and PN. On the other hand, mechanical efficiency, brake thermal efficiency, CO2, NOx and PM decreased with oxygen ratio. Increasing the oxygen content of the fuel was associated with a decrease in indicated power, brake power, indicated mean effective pressure, brake mean effective pressure, friction power, blow-by, CO2, CO (at higher loads), HC, PM and PN. On the other hand, the brakespecific fuel consumption, brake thermal efficiency and NOx increased by using the oxygenated fuels. Also, by increasing the oxygen content, the accumulation mode count median diameter moved toward the smaller particle sizes. In addition to the oxygen content of fuel, the other physical and chemical properties of the fuels were used to interpret the behavior of the engine.

Experimental and theoretical investigation of compression of a cylinder using a rotating platen

A rig was constructed to carry out compression of an aluminum cylinder with a monotonically rotating platen. The tests carried out showed that the compression load decreased and the side wall bulge severity reduced when the die was rotated. Not all the work supplied by the rotating dies was transferred to the work-piece; circumferential slippage was frequently observed at the die/material interface. This slippage was quantified by comparing measurements made during interrupted testing with the angular velocity of the die. A compound velocity field based on an exponential cusp description of the barreling was employed in an upper bound analysis. An approximate analytical solution was obtained for the degree of barreling and the compression pressure. The model is able to reproduce the decrease in barreling and compression loads with increasing die rotation.

Resistance to compression behavior of alpaca and wool

This study compares the resistance to compression behavior of wool and alpaca fibers. It shows that alpaca fibers have a much lower resistance to compression than wool, and there is little correlation between the resistance to compression and the curvature for alpaca fibers. Yet for wool fibers, the correlation between resistance to compression and curvature is very strong and positive. The differences in fiber curvature and scale profiles of alpaca and wool, together with the test method for resistance to compression, may explain their different resistances to compression.

Friction changes during compression tests using tool rotation technique

A compression test with rotating dies was employed to estimate the friction factor between aluminum samples and steel tooling during large plastic deformations. A cylindrical workpiece was compressed under dry and cold conditions. The magnitudes of torque and normal force were measured and
the average friction factor was calculated using the Coulomb friction law. It was found that under certain conditions the friction increased with increasing angular velocity of the die. This finding led to the conclusion that the choice of die rotation speed is important in interpreting the results from the twist compression test.

Influence of z-pinning on the buckling of composite laminates under edge-wise compression

Z-pinning is a newly developed technique to enhance the strength of composite laminates in the thickness direction. Recent experimental and theoretical studies have shown that z-pins significantly improve mode I and mode II fracture toughness. In practice, buckling accompanying delamination is a typical failure mode in laminated composite structures. For a complete understanding of the z-pinning technique towards improvements of the overall mechanical properties of laminated composites, a numerical model is developed in this paper to investigate the influence of z-pins on the buckling composite laminates with initial delaminations under edge-wise compression. The numerical results indicate that z-pinning can indeed effectively increase the compressive strength of the composite laminates provided that the initial imperfection is within a certain range. The magnitude of the improvement is consistent with available experimental data.

Deformation behaviour of a cylinder under simultaneous compression and torsion

A number of experiments involving the compression of an Aluminum cylinder with concurrent die rotation were carried out. Two important features were observed: one was that die rotation reduced the degree of bulging and the other was that the compression load decreased. An upper bound analysis with a velocity field consisting of a compound exponential cusp representation was utilized to obtain an approximate analytical solution in a closed form. The theoretical result reproduced the reduction in bulging severity with die rotation as well as the changes in compression pressure.

Stress analysis of compression of aluminium with rotating tools

Compression tests carried out on aluminium specimens showed that when the die was rotated the compression load dropped. A slab method is employed to examine this process. The load reduction is explained by the deviation of friction vector due to the relative circumferential movement between the die and the material. This mechanism is incorporated into a theoretical model and an expression is derived for compression pressure. Analytical solutions established compare favourably with experimental results. It is also shown that there is a limitation to the load reduction: the compressive load can never be lower than 70 percent of the yield limit.

E-democracy: media-liminal space in the era of age compression

In this chapter, the authors will look at the ideas of e-government and e-governance and practical examples of how new media are being used to enhance decision-making in democratic societies. The authors argue that the learning environments that have emerged from interactive entertainment and other contexts signal a change in the nature and role of liminality-the transition to citizen and civic engagement-in modern society.

Dystopian visions of global capitalism : Philip Reeve's Mortal Engines and M. T. Anderson's Feed

This article examines Philip Reeve’s novel for children, Mortal Engines, and M.T. Anderson’s young adult novel, Feed, by assessing these dystopias as prototypical texts of what Ulrich Beck calls risk society. Through their visions of a fictional future, the two narratives explore the hazards created by contemporary techno-economic progress, predatory global politics and capitalist excesses of consumption. They implicitly pose the question: “In the absence of a happy ending for western civilisation, what kind of children can survive in dystopia?”