45 resultados para Compress-and-Forward
em Deakin Research Online - Australia
Resumo:
Cooperative communication (CC) offers an efficient and low-cost way to achieve spatial diversity by forming a virtual antenna array among single-antenna nodes that cooperatively share their antennas. It has been well recognized that the selection of relay nodes plays a critical role in the performance of CC. Most existing relay selection strategies focus on optimizing the outage probability or energy consumption. To fill in the vacancy of research on throughput improvement via CC, we study the relay selection problem with the objective of optimizing the throughput in this paper. For unicast, it is a P problem, and an optimal relay selection algorithm is provided with a correctness proof. For broadcast, we show the challenge of relay selection by proving it nonprobabilistic hard (NP-hard). A greedy heuristic algorithm is proposed to effectively choose a set of relay nodes that maximize the broadcast throughput. Simulation results show that the proposed algorithms can achieve high throughput under various network settings.
Resumo:
Colour removal and the flux behaviour of nanofiltration (NF-DOW FILMTEC-NF245) and forward osmosis (FO-a flat sheet cellulose triacetate membrane with a woven embedded backing support) membranes were investigated in this study. The NF membrane was employed to perform dye removal experiments with aqueous solutions containing 15 g/L of NaCl and different concentrations of Acid Green 25, Remazol Brilliant Orange FR and Remazol Blue BR dyes. The increase in dye concentration resulted in a decline in water permeability and an increase in colour removal. When the concentrations of dye solutions varied from 250 to 1000 mg/L, at 0.8 bar of trans-membrane pressure, the NF system exhibited a steady permeate flux of more 30 L/m2h and a colour removal of more than 99%; salt rejection was more than 20.0%. Furthermore, the FO system possessed high dye rejection efficiency (almost 100%), with low permeate flux of around 2.0 L/m2h, when using dye solutions as feed streams and seawater as draw stream. The mode of operation (either FO or pressure retarded osmosis (PRO) did not change the flux significantly but PRO mode always produced higher fluxes than FO mode under the operating conditions used in this study. While both NF and FO can be used to reduce the volume of effluent containing dyes from textile industries, the energy spent in NF on applied pressure can be substituted by the osmotic pressure of draw solution in FO when concentrated draw solutions such as sea water or reverse osmosis concentrate are readily available.
Resumo:
In this paper, we investigate the impact of channel estimation error on the achievable common rate and error performance of amplify and forward (AF) multi-way relay networks (MWRNs). Assuming lattice codes with large dimensions, we provide the analytical expressions for the end-to-end SNR at the users and obtain upper bounds on the achievable common rate for an AF MWRN. Moreover, considering binary phase shift keying (BPSK) modulation as the simplest case of lattice codes, we obtain the average bit error rate (BER) for a user in an AF MWRN. The analysis shows that the average BER is a linearly increasing function and the achievable common rate is a linearly decreasing function of the channel estimation error. On the other hand, the average BER decreases and the achievable common rate increases with increasing correlation between the true and the estimated channel. Also, we observe that the AFprotocol is robust against increasing number of users in terms of error performance. We show that when the decoding user has better channel conditions compared to other users, AF relaying gives a better error performance and common rate. Finally, simulation results are provided to verify the validity of our analysis.
Resumo:
Objective To examine associations between shopping, food preparation, meal and eating behaviours and fruit and vegetable intake among women.
Design Cross-sectional survey.
Setting Community-based sample from metropolitan Melbourne, Australia.
Subjects A sample of 1136 women aged 18–65 years, randomly selected from the electoral roll.
Results Food-related behaviours reflecting organisation and forward-planning, as well as enjoyment of and high perceived value of meal shopping, preparation and consumption were associated with healthier intakes of fruits and vegetables. For example, women who more frequently planned meals before they went shopping, wrote a shopping list, enjoyed food shopping, planned in the morning what they will eat for dinner that night, planned what they will eat for lunch, reported they enjoy cooking, liked trying new recipes and who reported they sometimes prepare dishes ahead of time were more likely to consume two or more servings of vegetables daily. Conversely, women who frequently found cooking a chore, spent less than 15 minutes preparing dinner, decided on the night what they will eat for dinner, ate in a fast-food restaurant, ate takeaway meals from a fast-food restaurant, ate dinner and snacks while watching television and who frequently ate on the run were less likely to eat two or more servings of vegetables daily.
Conclusions Practical strategies based on these behavioural characteristics could be trialled in interventions aimed at promoting fruit and vegetable consumption among women.
Resumo:
The development and use of cocycles for analysis of non-autonomous behaviour is a technique that has been known for several years. Initially developed as an extension to semi-group theory for studying rion-autonornous behaviour, it was extensively used in analysing random dynamical systems [2, 9, 10, 12]. Many of the results regarding asymptotic behaviour developed for random dynamical systems, including the concept of cocycle attractors were successfully transferred and reinterpreted for deterministic non-autonomous systems primarily by P. Kloeden and B. Schmalfuss [20, 21, 28, 29]. The theory concerning cocycle attractors was later developed in various contexts specific to particular classes of dynamical systems [6, 7, 13], although a comprehensive understanding of cocycle attractors (redefined as pullback attractors within this thesis) and their role in the stability of non-autonomous dynamical systems was still at this stage incomplete. It was this purpose that motivated Chapters 1-3 to define and formalise the concept of stability within non-autonomous dynamical systems. The approach taken incorporates the elements of classical asymptotic theory, and refines the notion of pullback attraction with further development towards a study of pull-back stability arid pullback asymptotic stability. In a comprehensive manner, it clearly establishes both pullback and forward (classical) stability theory as fundamentally unique and essential components of non-autonomous stability. Many of the introductory theorems and examples highlight the key properties arid differences between pullback and forward stability. The theory also cohesively retains all the properties of classical asymptotic stability theory in an autonomous environment. These chapters are intended as a fundamental framework from which further research in the various fields of non-autonomous dynamical systems may be extended. A preliminary version of a Lyapunov-like theory that characterises pullback attraction is created as a tool for examining non-autonomous behaviour in Chapter 5. The nature of its usefulness however is at this stage restricted to the converse theorem of asymptotic stability. Chapter 7 introduces the theory of Loci Dynamics. A transformation is made to an alternative dynamical system where forward asymptotic (classical asymptotic) behaviour characterises pullback attraction to a particular point in the original dynamical system. This has the advantage in that certain conventional techniques for a forward analysis may be applied. The remainder of the thesis, Chapters 4, 6 and Section 7.3, investigates the effects of perturbations and discretisations on non-autonomous dynamical systems known to possess structures that exhibit some form of stability or attraction. Chapter 4 investigates autonomous systems with semi-group attractors, that have been non-autonomously perturbed, whilst Chapter 6 observes the effects of discretisation on non-autonomous dynamical systems that exhibit properties of forward asymptotic stability. Chapter 7 explores the same problem of discretisation, but for pullback asymptotically stable systems. The theory of Loci Dynamics is used to analyse the nature of the discretisation, but establishment of results directly analogous to those discovered in Chapter 6 is shown to be unachievable. Instead a case by case analysis is provided for specific classes of dynamical systems, for which the results generate a numerical approximation of the pullback attraction in the original continuous dynamical system. The nature of the results regarding discretisation provide a non-autonomous extension to the work initiated by A. Stuart and J. Humphries [34, 35] for the numerical approximation of semi-group attractors within autonomous systems. . Of particular importance is the effect on the system's asymptotic behaviour over non-finite intervals of discretisation.
Resumo:
A methodology for the numerical solution of the forward kinematics problem of 6-RRCRR parallel manipulators with orthogonal non-intersecting RR-joint configuration is presented in this article. The inverse and forward kinematics solutions of such robots compared with that of parallel robots with orthogonal intersecting RR-joint or universal joint configurations are much more complicated due to the existence of dependent joint variables. The constraints of RR-joints are analysed and the numerical algorithm for the forward kinematics solution is assessed. Numerical results for the solution of the forward kinematics of 6-RRCRR parallel robot under study are provided to confirm the accuracy and efficiency of the procedure.
Resumo:
The relationships were investigated between the prickle discomfort scores, assessed by human response from wearer trial garment assessment, and sleeve trial, Wool ComfortMeter (WCM) and Wool HandleMeter (WHM) assessments of fabrics, and fiber diameter characteristics including mean fiber diameter (MFD). Sleeve trial assessment followed exercise, the use of a control sleeve to reduce participant variance and four sensory traits. WHM provides eight handle parameters calibrated against a panel of experts. Four scenarios were evaluated: sleeve trial assessment with MFD; sleeve trial assessment with MFD and WCM; sleeve trial assessment with MFD, WCM and WHM parameters; and sleeve trial assessment with WCM and WHM parameters. Data were analyzed using correlation and forward stepwise general linear modeling. There was no evidence that the incidence of fibers coarser than 30 µm aided the prediction of prickle discomfort once MFD had been accounted for in the models. There were significant correlations between the WCM measurement and each sleeve trial attribute. There was no significant correlation between WHM parameters and sleeve trial assessments. The sleeve trial attribute of ‘skin feel’ offers potential to improve the predictions made of wearer trial prickle discomfort when used in association of the WCM with or without data on fabric MFD. There was little evidence to support using WHM parameters with or without the WCM in predicting wearer assessed prickle discomfort of fabrics. These results indicate that the rapid evaluation of fabrics using sleeve trial assessment can provide cost effective ranking of consumer preferences.
Resumo:
Parallel mechanisms possess several advantages such as the possibilities for high acceleration and high accuracy positioning of the end effector. However, most of the proposed parallel manipulators suffer from a limited workspace. In this paper, a novel 6-DOF parallel manipulator with coaxial actuated arms is introduced. Since parallel mechanisms have more workspace limitations compared to that of serial mechanisms, determination of the workspace in parallel manipulators is of the utmost importance. For finding position, angular velocity, and acceleration, in this paper, inverse and forward kinematics of the mechanism are studied and after presenting the workspace limitations, workspace analysis of the hexarot manipulator is performed by using MATLAB software. Next, using the obtained cloud of points from simulation, the overall borders of the workspace are illustrated. Finally, it is shown that this manipulator has the important benefits of combining a large positional workspace in relation to its footprint with a sizable range of platform rotations.
Resumo:
This work presents a hybrid controller based on the combination of fuzzy logic control (FLC) mechanism and internal model-based control (IMC). Neural network-based inverse and forward models are developed for IMC. After designing the FLC and IMC independently, they are combined in parallel to produce a single control signal. Mean averaging mechanism is used to combine the prediction of both controllers. Finally, performance of the proposed hybrid controller is studied for a nonlinear numerical plant model (NNPM). Simulation result shows the proposed hybrid controller outperforms both FLC and IMC.
Resumo:
Introduction The number of drivers with dementia is expected to increase exponentially over the coming decades. Most individuals with moderate-to-severe dementia (table 1) are unfit to drive.1 Drivers with moderate-to-severe dementia have higher rates of MVCs than age-matched controls.2 Identifying and preventing these individuals from driving is crucial, particularly in urban areas. The density of cars and pedestrians, and the complexity of traffic typically place greater demands on drivers in urban areas, and, therefore, require greater reactivity and forward planning than in rural environments.3 ,4 The ability to drive is a critical means of maintaining one's social inclusion, and is commonly a practical necessity. Therefore, decisions about the entitlement to drive should not unfairly restrict mobility or unnecessarily compound the disadvantages experienced by older people with mild cognitive impairment and early dementia (table 1), particularly as diagnoses are now being made earlier.1 This paper describes the difficulties inherent in addressing the question of when and in what circumstances a diagnosis of dementia might render a person unfit to drive and focuses on those who live in rural areas. We examine the consequences of dementia diagnosis on driving, driver testing requirements and licensing procedures, and the impacts of driving cessation. We then discuss how living in rural areas may alter the level of risk of drivers with dementia and practical implications for licensing policies.
Resumo:
BACKGROUND: There have been some disagreements on the comparison of disc pressures in the standing and sitting postures in literature. Most research on in vivo pressure needle measurement found higher disc pressure in sitting than in standing. The disc pressure data can help to advocate better postures for clinical advice. OBJECTIVE: The aim of this paper is to develop a procedure to study the compressive load on intervertebral joint in the standing and sitting postures through the approach of motion capture and musculoskeletal modeling. METHODS: The marker data of six subjects performing various standing and sitting postures was obtained during the motion capture experiment and used to train the musculoskeletal model with an enhanced discretized spine developed for subject in the inverse and forward simulations. RESULTS: Compressive loads on L3-L4 and L4-L5 joints are found higher in upright sitting than in upright standing. Slumped sitting, cross-legged sitting and flexion sitting can introduce higher compressive loads on intervertebral joints compared with upright sitting. CONCLUSIONS: These findings indicate the effects of standing and sitting postures on the spinal joint loads. The results can provide doctors and therapists with more information on clinical advice on better postures for people with spinal problems.
Resumo:
The hypothetical extraction method (HEM) is used to extract a sector hypothetically from an economic system and examine the influence of this extraction on other sectors in the economy. Linkage measures based on the HEM become increasingly prominent. However, little construction linkage research applies the HEM. Using the recently published Organisation for Economic Co-operation and Development input-output database at constant prices, this research applies the HEM to the construction sector in order to explore the role of this sector in national economies and the quantitative interdependence between the construction sector and the remaining sectors. The output differences before and after the hypothetical extraction reflect the linkages of the construction sector. Empirical results show a declining trend of the total, backward and forward linkages, which confirms the decreasing role of the construction sector with economic maturity over the examined period from a new angle. Analytical results reveal that the unique nature of the construction sector and multifold external factors are the main reasons for the linkage difference between countries. Moreover, hypothesis-testing results consider statistically that the extraction structures employed in this research are appropriate to analyse the linkages of the construction sector.
Resumo:
Construction linkage is a well-established research field. However, a significant limitation in previous linkage research is that the flow of capital goods is not addressed. Using the OECD input-output tables, this research first generates a new input-output model considering capital as an intermediate factor. Using the new model, the construction linkages are recalculated and investigated in order to evaluate further the role of construction in national economies. The findings verify that traditional construction linkages were extremely underestimated in previous research. Furthermore, the effect of capital on construction shows a declining trend over the examined period. After considering the effect of capital, most values and rankings of backward and forward linkages show a decreasing trend, which confirms the declining role of the construction sector with economic maturity.
Resumo:
This paper provides survey evidence captured from a sample of 113 respondents to a 2008 questionnaire sent to 344 companies in Thailand. The study examines Thai hedging practices following the Asian Financial Crisis of 1997. Thai companies, like their international counterparts, rely predominantly on matching and forward contracts to hedge transaction exposure. Thai companies, however, appear to be less rigorous when it comes to internal control and supervision of derivative activity. It is recommended that Thai companies improve their risk management practices by putting into place a documented hedging policy, which includes a requirement that senior staff be actively engaged in the risk management activities of the firm.
Resumo:
In this paper, we propose a novel approach to secure ownership transfer in RFID systems based on the quadratic residue property. We present two secure ownership transfer schemes-the closed loop and open loop schemes. An important property of our schemes is that ownership transfer is guaranteed to be atomic. Further, both our schemes are suited to the computational constraints of EPC Class-1 Gen-2 passive RFID tags as they only use operations that such passive RFID tags are capable of. We provide a detailed security analysis to show that our schemes achieve strong privacy and satisfy the required security properties of tag anonymity, tag location privacy, forward secrecy, and forward untraceability. We also show that the schemes are resistant to replay (both passive and algebraic), desynchronization, and server impersonation attacks. Performance comparisons demonstrate that our schemes are practical and can be implemented on low-cost passive RFID tags.