Correlation between microstructure and phosphorus segregation in a hypereutectoid Wootz steel

The influence of bands rich in phosphorus on the microstructure of hypereutectoid Wootz steel implement is described. Electron probe micro-analysis is combined with optical microscopy. Phosphorus-rich bands are seen to correspond to regions of internal cracking, carbon depletion, and enhanced frequency of spheroidized cementite in place of pearlite. A rationale for the findings is presented in terms of the influence of phosphorus on the Fe–C phase diagram and on the rate of the eutectoid reaction.

Sexual niche segregation and gender-specific individual specialisation in a highly dimorphic marine mammal

While sexual segregation is expected in highly dimorphic species, the local environment is a major factor driving the degree of resource partitioning within a population. Sexual and individual niche segregation was investigated in the Australian fur seal (Arctocephalus pusillus doriferus), which is a benthic foraging species restricted to the shallow continental shelf region of south-eastern Australia. Tracking data and the isotopic values of plasma, red blood cells and whiskers were combined to document spatial and dietary niche segregation throughout the year. Tracking data indicated that, in winter, males and females overlapped in their foraging habitat. All individuals stayed within central Bass Strait, relatively close (< 220 km) to the breeding colony. Accordingly, both genders exhibited similar plasma and red cell δ13C values. However, males exhibited greater δ13C intra-individual variation along the length of their whisker than females. This suggests that males exploited a greater diversity of foraging habitats throughout the year than their female counterparts, which are restricted in their foraging grounds by the need to regularly return to the breeding colony to suckle their pup. The degree of dietary sexual segregation was also surprisingly low, both sexes exhibiting a great overlap in their δ15N values. Yet, males displayed higher δ15N values than females, suggesting they fed upon a higher proportion of higher trophic level prey. Given that males and females exploit different resources (mainly foraging habitats), the degree of individual specialisation might differ between the sexes. Higher degrees of individual specialisation would be expected in males which exploit a greater range of resources. However, comparable levels of inter-individual variation in δ15N whisker values were found in the sampled males and females, and, surprisingly, all males exhibited similar seasonal and inter-annual variation in their δ13C whisker values, suggesting they all followed the same general dispersion pattern throughout the year.

The combined tensile and torsional behavior of irregular fibers

Most fibers are irregular, and they are often subjected to combined loading conditions during processing and end-use. In this paper, polyester and wool fibers under the combined tensile and torsional loads have been studied for the first time, using the finite element method (FEM). The dimensional irregularities of these fibers are simulated with sine waves of different magnitude and frequency. The breaking load and breaking extension of the fibers at different twist or torsion levels are then calculated from the finite element model. The results indicate that twist and level of fiber irregularity have a major impact on the mechanical properties of the fiber and the effect of the frequency of irregularity is relatively small.

Bitterness suppression with zinc sulfate and na-cyclamate: a model of combined peripheral and central neural approaches to flavor modification

Purpose Zinc sulfate is known to inhibit the bitterness of the antimalarial agent quinine [R. S. J. Keast. The effect of zinc on human taste perception. J. Food Sci. 68:1871–1877 (2003)]. In the present work, we investigated whether zinc sulfate would inhibit other bitter-tasting compounds and pharmaceuticals. The utility of zinc as a general bitterness inhibitor is compromised, however, by the fact that it is also a good sweetness inhibitor [R. S. J. Keast, T. Canty, and P. A. S. Breslin. Oral zinc sulfate solutions inhibit sweet taste perception. Chem. Senses 29:513–521 (2004)] and would interfere with the taste of complex formulations. Yet, zinc sulfate does not inhibit the sweetener Na-cyclamate. Thus, we determined whether a mixture of zinc sulfate and Na-cyclamate would be a particularly effective combination for bitterness inhibition (Zn) and masking (cyclamate).

Method We used human taste psychophysical procedures with chemical solutions to assess bitterness blocking.

Results Zinc sulfate significantly inhibited the bitterness of quinine–HCl, Tetralone, and denatonium benzoate (DB) (p < 0.05), but had no significant effect on the bitterness of sucrose octa-acetate, pseudoephedrine (PSE), and dextromethorphan. A second experiment examined the influence of zinc sulfate on bittersweet mixtures. The bitter compounds were DB and PSE, and the sweeteners were sucrose (inhibited by 25 mM zinc sulfate) and Na-cyclamate (not inhibited by zinc sulfate). The combination of zinc sulfate and Na-cyclamate most effectively inhibited DB bitterness (86%) (p < 0.0016), whereas the mixture's inhibition of PSE bitterness was not different from that of Na-cyclamate alone.

Conclusion A combination of Na-cyclamate and zinc sulfate was most effective at inhibiting bitterness. Thus, the combined use of peripheral oral and central cognitive bitterness reduction strategies should be particularly effective for improving the flavor profile of bitter-tasting foods and pharmaceutical formulations.

Vascular attack by 5,6-dimethylxanthenone-4-acetic acid combined with B7.1 (CD80)-mediated immunotherapy overcomes immune resistance and leads to the eradication of large tumors and multiple tumor foci

The promise of cancer immunotherapy is that it will not only eradicate primary tumors but will generate systemic antitumor immunity capable of destroying distant metastases. A major problem that must first be surmounted relates to the immune resistance of large tumors. Here we reveal that immune resistance can be overcome by combining immunotherapy with a concerted attack on the tumor vasculature. The functionally related antitumor drugs 5,6-dimethylxanthenone-4-acetic acid (DMXAA) and flavone acetic acid (FAA), which cause tumor vasculature collapse and tumor necrosis, were used to attack the tumor vasculature, whereas the T-cell costimulator B7.1 (CD80), which costimulates T-cell proliferation via the CD28 pathway, was used to stimulate antitumor immunity. The injection of cDNA (60–180 µg) encoding B7.1 into large EL-4 tumors (0.8 cm in diameter) established in C57BL/6 mice, followed 24 h later by i.p. administration of either DMXAA (25 mg/kg) or FAA (300 mg/kg), resulted in complete tumor eradication within 2–6 weeks. In contrast, monotherapies were ineffective. Both vascular attack and B7.1 immunotherapy led to up-regulation of heat shock protein 70 on stressed and dying tumor cells, potentially augmenting immunotherapy. Remarkably, large tumors took on the appearance of a wound that rapidly ameliorated, leaving perfectly healed skin. Combined therapy was mediated by CD8+ T cells and natural killer cells, accompanied by heightened and prolonged antitumor cytolytic activity (P < 0.001), and by a marked increase in tumor cell apoptosis. Cured animals completely rejected a challenge of 1 x 107 parental EL-4 tumor cells but not a challenge of 1 x 104 Lewis lung carcinoma cells, demonstrating that antitumor immunity was tumor specific. Adoptive transfer of 2 x 108 splenocytes from treated mice into recipients bearing established (0.8 cm in diameter) tumors resulted in rapid and complete tumor rejection within 3 weeks. Although DMXAA and B7.1 monotherapies are complicated by a narrow range of effective doses, combined therapy was less dosage dependent. Thus, a broad range of amounts of B7.1 cDNA were effective in combination with 25 mg/kg DMXAA. In contrast, DMXAA, which has a very narrow range of high active doses, was effective at a low dose (18 mg/kg) when administered with a large amount (180 µg) of B7.1 cDNA. Importantly, combinational therapy generated heightened antitumor immunity, such that gene transfer of B7.1 into one tumor, followed by systemic DMXAA treatment, led to the complete rejection of multiple untreated tumor nodules established in the opposing flank. These findings have important implications for the future direction and utility of cancer immunotherapies aimed at harnessing patients’ immune responses to their own tumors.

Degradation mechanisms of benzo[a]pyrene and its accumulated metabolites by biodegradation combined with chemical oxidation

A high degradation extent of benzo[a]pyrene (BaP) should not be considered as the sole desirable criterion for the bioremediation of BaP-contaminated soils because some of its accumulated metabolites still have severe health risks to human. Two main metabolites of BaP, benzo[a]pyrene-1,6-quinone (BP1,6-quinone) and 3-hydroxybenzo[a]pyrene (3-OHBP) were identified by high performance liquid chromatography (HPLC) with standards. This study was the first time that degradation of both BaP and the two metabolites was carried out by chemical oxidation and biodegradation. Three main phases during the whole degradation process were proposed.

Hydrogen peroxide–zinc (H₂O₂–Zn), the fungus – Aspergillus niger and the bacteria – Zoogloea sp. played an important role in the different phases. The degradation parameters of the system were also optimized, and the results showed that the effect of degradation was the best when fungus–bacteria combined with H₂O₂–Zn, the concentration range of BaP in the cultures was 30–120 mg/l, the initial pH of the cultures was 6.0. However, as co-metabolites, phenanthrene significant inhibited the degradation of BaP. This combined degradation system compared with the conventional method of degradation by domestic fungus only, enhanced the degradation extent of BaP by more than 20% on the 12 d. The highest accumulation of BP1,6-quinone and 3-OHBP were reduced by nearly 10% in the degradation experiments, which further proved that the combined degradation system was more effective as far as joint toxicity of BaP and its metabolites are concerned.

Exercise and calcium combined results in a Greater osteogenic effect than either factor alone: a blinded randomized placebo-controlled trial in boys

We examined the combined effects of exercise and calcium on BMC accrual in pre- and early-pubertal boys. Exercise and calcium together resulted in a 2% greater increase in femur BMC than either factor alone and a 3% greater increase in BMC at the tibia–fibula compared with the placebo group. Increasing dietary calcium seems to be important for optimizing the osteogenic effects of exercise.

Introduction: Understanding the relationship between exercise and calcium during growth is important given that the greatest benefits derived from these factors are achieved during the first two decades of life. We conducted a blinded randomized-controlled exercise–calcium intervention in pre- and early-pubertal boys to test the following hypotheses. (1) At the loaded sites (femur and tibia–fibula), exercise and calcium will produce greater skeletal benefits than either exercise or calcium alone. (2) At nonloaded sites (humerus and radius–ulna), there will be an effect of calcium supplementation.

Materials and Methods: Eighty-eight pre- and early-pubertal boys were randomly assigned to one of four study groups: moderate impact exercise with or without calcium (Ca) (Ex + Ca and Ex + placebo, respectively) or low impact exercise with or without Ca (No-Ex + Ca and No-Ex + Placebo, respectively). The intervention involved 20 minutes of either moderate- or low-impact exercise performed three times a week and/or the addition of Ca-fortified foods using milk minerals (392 ± 29 mg/day) or nonfortified foods over 8.5 months. Analysis of covariance was used to determine the main and combined effects of exercise and calcium on BMC after adjusting for baseline BMC.

Results: At baseline, no differences were reported between the groups for height, weight, BMC, or bone length. The increase in femur BMC in the Ex + Ca group was 2% greater than the increase in the Ex + placebo, No-Ex + Ca, or No-Ex + Placebo groups (all p < 0.03). At the tibia–fibula, the increase in BMC in the Ex + Ca group was 3% greater than the No-Ex + placebo group (p < 0.02) and 2% greater than the Ex + Placebo and the No-Ex + Ca groups (not significant). No effect of any group was detected at the humerus, ulna–radius, or lumbar spine for BMC, height, bone area, or volume.

Conclusions: In this group of normally active boys with adequate calcium intakes, additional exercise and calcium supplementation resulted in a 2–3% greater increase in BMC than controls at the loaded sites. These findings strengthen the evidence base for public health campaigns to address both exercise and dietary changes in children for optimizing the attainment of peak BMC.

Using titania photocatalysts to degrade toluene in a combined adsorption and photocatalysis process

Three types of titania supported materials including titanium dioxide and silicon dioxide composite, titania-coated activated carbon and titania-coated glass beads were prepared and used as photocatalysts to remove toluene from an air stream. Their surface areas were analysed. TEM image reveals titania-silica composites were nanostructured aggregates. XRD was used to determine their crystalline phase which was 100% anatase for the titania component. A fixed bed reactor was designed and built in the laboratory, the toluene with initial concentration of 300 ppm (1149 mg/m³) was fed into the reactor, the destruction efficiencies of toluene were determined by the gas analyser. It was also found that TiO₂-SiO₂ aggregates with high surface area (421.1 m²/g) achieved high destruction efficiencies. The combined effects of adsorption and photocatalysis were further studied by comparing the performance of pure activated carbon (surface area of 932.4 m²/g) and TiO₂ coated activated carbon with BET surface area of 848.4 m²/g. It was found that the TiO₂ coated activated carbon demonstrated comparable results to pure activated carbon, and most importantly, the TiO₂-coated activated carbon can be effectively regenerated by UV irradiation, and was reused as adsorbent. The experimental result of titania-coated glass beads demonstrated a steady degradation efficiency of 15% after a period of 17 hours. It helped to understand that photocatalysis degradation ability of the TiO₂ was constant regardless of the adsorption capacity of the catalysts. This photocatalytic property can be used to degrade the adsorbed toluene and regenerate the catalyst. This study revealed that if the experiments were designed to use adsorption to remove toluene and followed by regeneration of adsorbent using photocatalysis, it could achieve a very high removal efficiency of toluene and reduce the regeneration cost of saturated adsorbent.

Use of in vitro critical inhibitory concentration, a novel approach to predict in vivo synergistic bactericidal effect of combined amikacin and piperacillin against pseudomonas aeruginosa in a systemic rat infection model

PURPOSE: This study was undertaken to explore the use of in vitro critical inhibitory concentration (CIC) as a surrogate marker relating the pharmacokinetic (PK) parameters to in vivo bactericidal synergistic effect [pharmacodynamic (PD)] of amikacin + piperacillin combination against Pseudomonas aeruginosa in a systemic rat infection model. METHODS: The in vitro antibacterial activities of amikacin and piperacillin, alone and in combinations at various ratios of the concentrations, were tested against a standard [5 x 10(5) colony-forming units (CFU)/ml] and a large (1.5 x 10(8) CFU/ml) inoculum of P. aeruginosa ATCC 9027 using a modified survival-time method. The CIC of each individual antibiotic for the different combinations was determined using a cup-plate method. In vivo studies were performed on Sprague-Dawley rats using a systemic model of infection with P. aeruginosa ATCC 9027. PK profiles and in vivo killing effects of the combination at different dosing ratios were studied. RESULTS: An inoculum effect was observed with the antibiotics studied. Synergy was seen against both the inocula at the following concentration ratios: 70% C(ami) + 30% C(pip) and 75% C(ami) + 25% C(pip), where C(ami) and C(pip) are the concentrations of amikacin and piperacillin to produce a 1000-fold decrease in bacterial population over 5 h, respectively. The CIC values determined corroborated with the order of in vitro bacterial killing observed for the antibiotic combinations. The dosing ratio of 12.6 mg/kg amikacin + 36 mg/kg piperacillin (a 70:30 ratio of the individual doses) exhibited the greatest killing in vivo when compared to the other ratios. The PK-PD relationships were described by simple, linear regression equations using the area under the in vivo killing curve as a PD marker and the AUCIC(ami)/CIC(ami) + AUCIC(pip)/CIC(pip), AUC(ami)/CIC(ami) + AUC(pip)/CIC(pip), C(max,ami)/CIC(ami) + C(max,pip)/CIC(pip), and AUCIC(ami)/MIC(ami) + AUCIC(pip)/MIC(pip) as PK markers for the amikacin + piperacillin combination. CONCLUSION: The combination of amikacin and piperacillin exhibited synergistic killing effect on P. aeruginosa that could be modeled using CIC as a surrogate marker relating the PK parameters to in vivo bactericidal effect.

Coronary artery stenoses: detection with calcium scoring, CT angiography, and both methods combined

PURPOSE: To investigate prospectively the relative accuracy of computed tomographic (CT) angiography, calcium scoring (CS), and both methods combined in demonstrating coronary artery stenoses by using conventional angiography as the reference standard. MATERIALS AND METHODS: The study was approved by the institutional review board Human Research Ethics Committee, and all patients completed written informed consent. Fifty patients (40 men, 10 women) aged 62 years ± 11 (± standard deviation) who were suspected of having coronary artery disease underwent both conventional coronary angiography and multisection coronary CT angiography with CS. Sensitivity and specificity of CS, CT angiography, and both methods combined in demonstrating luminal stenosis greater than or equal to 50% were determined for each arterial segment, coronary vessel, and patient. Receiver operating characteristic (ROC) curves were generated for CS prediction of significant stenosis, and the Mann-Whitney U test was used for comparison of CS between groups. RESULTS: When used with segment-specific electrocardiographic phase reconstructions, CT angiography demonstrated stenosed segments with 79% sensitivity and 95% specificity. Mean calcium score was greater in segments, vessels, and patients with stenoses than in segments, vessels, and patients without stenoses (P < .001 for all); nine (16%) of 56 stenosed segments, however, had a calcium score of 0. The patient calcium score correlated strongly with the number of stenosed arteries (Spearman {rho} = 0.75, P < .001). CS was more accurate in demonstrating stenosis in patients than in segments (areas under ROC curve were 0.88 and 0.74, respectively). CT angiography, however, was more accurate than CS in demonstrating stenosis in patients, vessels, and segments. The sensitivity and specificity of CS varied according to the threshold used, but when the calcium score cutoff (ie, >150) matched the specificity of CT angiography (95%), the sensitivity of CS in demonstrating stenosed segments was 29% (compared with 79% for CT angiography). Combining CT angiography with CS (at threshold of 400) improved the sensitivity of CT angiography (from 93% to 100%) in demonstrating significant coronary disease in patients, without a loss of specificity (85%); this finding, however, was not statistically significant. CONCLUSION: CT angiography is more accurate than CS in demonstrating coronary stenoses. A patient calcium score of greater than or equal to 400, however, can be used to potentially identify patients with significant coronary stenoses not detected at CT angiography.

Sexual segregation in western grey kangaroos: testing alternative evolutionary hypotheses

In sexually dimorphic ungulates, sexual segregation is hypothesized to have evolved because of sex-specific differences in body size and/or reproductive strategies. We tested these alternative hypotheses in kangaroos, which are ecological analogues of ungulates. Kangaroos exhibit a wide range of body sizes, particularly among mature males, and so the effects of body size and sex can be distinguished. We tested predictions derived from these hypotheses by comparing the distribution of three sex–sex size classes of western grey kangaroos Macropus fuliginosus, in different habitats, and the composition of groups of kangaroos, across seasons. In accordance with the predation risk-reproductive strategy hypothesis, during the non-breeding season, females, which were more susceptible to predation than larger males, and were accompanied by vulnerable young-at-foot, were over-represented in secure habitats. Large males, which were essentially immune to predation, occurred more often than expected in nutrient-rich habitat, and small males, which faced competing demands of predator avoidance and feeding, were intermediate between females and large males in their distribution across habitats. During the breeding season, females continued to be over-represented in secure habitats when their newly emerged pouch young were most vulnerable to predation. All males occupied these same habitats to maximize their chances of securing mates. Consistent with the social hypotheses, groups composed of individuals of the same sex, irrespective of body size, were over-represented in the population during the non-breeding season, while during the breeding season all males sought females so that mixed-sex groups predominated. These results indicate that body size and reproductive strategies are both important, yet independent, factors influencing segregation in western grey kangaroos.

Combined evaluation of workplace performance using occupants' subjective assessment and objective measurement of environmental conditions : a case study

The case study presents findings from a program of pre- and post-evaluations of buildings sponsored by the NSW government. The program aims to demonstrate leadership in the delivery of government accommodation and to provide feedback into the building design and management process.

The results from a combined evaluation of an ABGR 4.5 star government building using the KODO probe© occupant surveys and measures of environmental conditions, carried out by the Mobile Architecture and Built Environment Laboratory (MABEL) at Deakin University are summarised. In particular the paper will present the benefits of innovative performance evaluation of property for commercial benefit using the KODO productivity topographic maps©.

These maps isolate where facility solutions are needed as opposed to tenant/occupant solutions in order to optimise building and business outcomes with minimal capital investment.

Power analysis and simulation of a vehicle under combined loads

This paper presents an analytical model of fuel consumption (AMFC) to coordinate the driving power and manage the overall fuel consumption for an internal combustion engine vehicle. The model calculates the different loads applied on the vehicle including road-slope, road-friction, wind-drag, accessories, and mechanical losses. Also, it solves the combustion equation of the engine under different working conditions including various fuel compositions, excess airs and air inlet temperatures. Then it determines the contribution of each load to signify the energy distribution and power flows of the vehicle. Unlike the conventional models in which the vehicle speed needs to be given as an input, the developed model can predict the vehicle speed and acceleration under different working conditions by allowing the speed to vary within a predefined range only. Furthermore, the model indicates the ways to minimises the vehicles' fuel consumption under various driving conditions. The results show that the model has the potential to assist in the vehicle energy management.

An intelligent energy management model for a parallel hybrid vehicle under combined loads

To exploit the benefits offered by parallel HEVs, an intelligent energy management model is developed and evaluated in this paper. Despite most existing works, the developed model incorporates combined wind/drag, slope, rolling, and accessories loads to minimise the fuel consumption under varying driving conditions. A slope prediction unit is also employed. The engine and the electric motor can output power simultaneously under a heavy-load or a slopped road condition. Two simulation were conducted namely slopped-windy-prediction and slopped-windy-prediction-hybrid. The results indicate that the vehicle speed and acceleration is smoother where the hybrid component was included. The average fuel consumption for the first and second simulations were 7.94 and 7.46 liter/100 km, respectively.