Geosynthetics in Antarctica: performance of a composite barrier system to contain hydrocarbon-contaminated soil after three years in the field

An overview of the design and performance of geosynthetics in composite barrier systems for biopiles used to remediate hydrocarbon-contaminated soil at Casey Station, Antarctica, is presented. Seven instrumented biopiles were constructed over three field seasons. To minimize the risk of hydrocarbon migration to groundwater, composite barrier systems were used (each using different combinations of geosynthetic clay liners (GCLs), high density polyethylene (HDPE) geomembranes (GMB), and geotextiles (GTXs)). One biopile used a co-extruded geomembrane (HDPE with an ethylene vinyl alcohol (EVOH) core). The liner system was subject to a combination of coupled phenomena that could interact and affect the GMB-GCL composite barrier performance. The exposure conditions involved potential freeze-thaw cycling, hydration-desiccation cycles, cation exchange, direct and diffusive exposure to hydrocarbons. The effect of these phenomena was investigated by monitoring GCL and GMB sacrificial coupons. GCL coupons were placed between the main GCL component and the main geomembrane component of the composite liner and GMB coupons placed between the main GMB sheet and the GTX protection layer. Coupons were exhumed from the biopiles each year. The exhumed GCL field moisture content values ranged from 162% to 22%. After three (3) years in the field, GCL coupons that had undergone at least one hydration/desiccation cycle showed no significant change in swell index values or fluid loss values. The measured hydraulic conductivity of exhumed GCL coupons from Biopiles 1 and 2 (3 × 10-11 m s-1) was within the expected range and not significantly different from the values for virgin GCL. GMB coupons exhumed after three years from Biopiles 1 and 2 showed no significant change in oxidative induction time (OIT), melt flow index or tensile properties. Diffusion tests were performed as an index test for establishing the performance of the GMBs as a diffusive barrier to hydrocarbons, with permeation parameters for BTEX contaminants ranging from P g = 0.9-9.2 × 10-13 m2 s-1 for the exhumed GMB (with values depending on the contaminant and GMB). These values were similar to the parameters obtained for virgin GMBs and there was no significant change with field exposure, with GMBs appearing to be performing well.

The COMPASS subunit Spp1 links histone methylation to initiation of meiotic recombination

During meiosis, combinatorial associations of genetic traits arise from homologous recombination between parental chromosomes. Histone H3 lysine 4 trimethylation marks meiotic recombination hotspots in yeast and mammals, but how this ubiquitous chromatin modification relates to the initiation of double-strand breaks (DSBs) dependent on Spo11 remains unknown. Here, we show that the tethering of a PHD-containing protein, Spp1 (a component of the COMPASS complex), to recombinationally cold regions is sufficient to induce DSB formation. Furthermore, we found that Spp1 physically interacts with Mer2, a key protein of the differentiated chromosomal axis required for DSB formation. Thus, by interacting with H3K4me3 and Mer2, Spp1 promotes recruitment of potential meiotic DSB sites to the chromosomal axis, allowing Spo11 cleavage at nearby nucleosome-depleted regions.

Understanding the deformed microstructure of cold-rolled IF and LC steel

This paper presents an overview of a series of investigations of the microstructure and texture of cold-rolled IF and LC steel. The investigations made extensive use of orientation mapping using electron backscattered diffraction (EBSD) in a field emission gun scanning electron microscope (FEG-SEM). The effect of grain boundaries on the deformed microstructure was examined by comparing the textures of regions near grain boundaries and in the interiors of grains.  A general weakening of the texture, but a strengthening of the {OOI}<110> component, occurs in the vicinity of grain boundaries. Misorientation angle and axis distributions were used to characterise the fragmentation of grains belonging to different orientation classes. The influence of carbon on the deformed microstructure and nucleation during recrystallization was clarified by examining the microstructures of LC and IF steels during rolling and annealing. The
results of the investigations emphasize the important role of shear banding in determining the fragmentation behaviour of ND-fibre grains and the orientations of viable recrystallization nuclei within the deformed microstructure.

Fragmentation of orientation within grains of a cold-rolled interstitial-free steel

The formation of a favourable recrystallization texture in interstitial-free (IF) steels depends on the availability and activation of particular nucleation sites in the deformed microstructure. This paper presents a description of the deformed microstructure of a commercially cold-rolled IF steel, with particular emphasis on the microstructural inhomogeneities and short-range orientational variation that provide suitable nucleation sites during recrystallization. RD-fibre regions deform relatively homogeneously and exhibit little short-range orientational variation. ND-fibre regions are heavily banded and exhibit considerable short-range orientational variation associated with the bands. While the overall orientational spread of ND-fibre grains frequently is about the ND-axis, the short-range orientational variation often involves rotation about axes in the TD-ND plane that are nearer to the TD than the ND.

Fault detection in a cold forging process through feature extraction with a neural network

This paper investigates the application of neural networks to the recognition of lubrication defects typical to an industrial cold forging process employed by fastener manufacturers. The accurate recognition of lubrication errors, such as coating not being applied properly or damaged during material handling, is very important to the quality of the final product in fastener manufacture. Lubrication errors lead to increased forging loads and premature tool failure, as well as to increased defect sorting and the re-processing of the coated rod. The lubrication coating provides a barrier between the work material and the die during the drawing operation; moreover it needs be sufficiently robust to remain on the wire during the transfer to the cold forging operation. In the cold forging operation the wire undergoes multi-stage deformation without the application of any additional lubrication. Four types of lubrication errors, typical to production of fasteners, were introduced to a set of sample rods, which were subsequently drawn under laboratory conditions. The drawing force was measured, from which a limited set of features was extracted. The neural network based model learned from these features is able to recognize all types of lubrication errors to a high accuracy. The overall accuracy of the neural network model is around 98% with almost uniform distribution of errors between all four errors and the normal condition.

Effect of cold drawing on subsequent surface strain path and ductility during upsetting

Cold drawing is a process that sizes and smooths the surface of steel before it is cold headed to produce bolts. The effect of the changes in the mechanical properties due to cold drawing on the surface strain and ductility during the upsetting process was analysed showing that the stress and strain state can be more readily altered by changes in the process conditions (friction and height-to-diameter ratio) to cause greater increase in the failure strains than can be achieved by pre-drawing.

Prediction of ductile fracture in the cold forging of steel

The thesis describes the development of a model of the cold forging process that accurately predicts the initiation of ductile fracture. The effect of the deformation history of the material during multiple forming operations is considered. Both two- and three-dimensional numerical models of the forging process were combined with a ductile fracture criterion to predict the material ductility and damage distribution in the workpiece.

Evaluation of cold forming lubricants for fastener manufacturing

Investigates the significance and interactive effects of lubricant type, workpiece surface texture and deformation rate under bulk metal, deformation conditions. A novel test rig was developed in conjunction with statistical test techniques. The result of this work identified a cold forming lubrication system with potential economic and environmental advantages over traditional lubrication systems.

The resurrection plant Sporobolus stapfianus: An unlikely model for engineering enhanced plant biomass?

The resurrection grass Sporobolus stapfianus Gandoger can rapidly recover from extended periods of time in the desiccated state (water potential equilibrated to 2% relative humidity) (Gaff and Ellis, Bothalia 11:305–308 1974; Gaff and Loveys, Transactions of the Malaysian Society of Plant Physiology 3:286–287 1993). Physiological studies have been conducted in S. stapfianus to investigate the responses utilised by these desiccation-tolerant plants to cope with severe water-deficit. In a number of instances, more recent gene expression analyses in S. stapfianus have shed light on the molecular and cellular mechanisms mediating these responses. S. stapfianus is a versatile research tool for investigating desiccation-tolerance in vegetative grass tissue, with several useful characteristics for differentiating desiccation-tolerance adaptive genes from the many dehydration-responsive genes present in plants. A number of genes orthologous to those isolated from dehydrating S. stapfianus have been successfully used to enhance drought and salt tolerance in model plants as well as important crop species. In addition to the ability to desiccate and rehydrate successfully, the survival of resurrection plants in regions experiencing short sporadic rainfall events may depend substantially on the ability to tightly down-regulate cell division and cell wall loosening activities with decreasing water availability and then grow rapidly after rainfall while water is plentiful. Hence, an analysis of gene transcripts present in the desiccated tissue of resurrection plants may reveal important growth-related genes. Recent findings support the proposition that, as well as being a versatile model for devising strategies for protecting plants from water-loss, resurrection plants may be a very useful tool for pinpointing genes to target for enhancing growth rate and biomass production.

Temperature conditions during 'cold' sheet metal stamping

This paper investigates the friction and deformation-induced heating that occurs during the stamping of high strength sheet steels, under room temperature conditions. A thermo-mechanical finite element model of a typical plane strain stamping process was developed to understand the temperature conditions experienced within the die and blank material; and this was validated against experimental measurements. A high level of correlation was achieved between the finite element model and experimental data for a range of operating conditions and parameters. The model showed that the heat generated during realistic production conditions can result in high temperatures of up to 108 °C and 181 °C in the blank and die materials, respectively, for what was traditionally expected to be 'cold' forming conditions. It was identified that frictional heating was primarily responsible for the peak temperatures at the die surface, whilst the peak blank temperatures were caused by a combination of frictional and deformation induced heating. The results provide new insights into the local conditions within the blank and die, and are of direct relevance to sheet formability and tool wear performance during industrial stamping processes. © 2014 Elsevier B.V. All rights reserved.

How online learning in an engineering-physics course helped us flip the classroom

Distance education has developed in the past 25 years or so as a way of supplying education to people who would not have access to local college education facilities. This includes students who live in remote regions, students who lack mobility, and students with full-time jobs. More recently this has been renamed to "online learning". Deakin University in Australia has been teaching freshman engineering physics simultaneously to on-campus and online students since the late1990's. The course is part of an online Bachelor of Engineering major that is accredited by the Institution of Engineers Australia.* In this way Deakin answers the call to provide engineering education "anywhere, anytime."**The course has developed and improved with the available educational technology. Starting with printed study guides, a textbook, CD-ROMS, and snail-mail, and telephone/email correspondence with students, the course has seen the rise of websites, online course notes, discussion boards, streamed video lectures, web-conferencing classes and lab sessions, and online submission of student work. Most recently the on-campus version of the course has shifted from a traditional lecture/tutorial/lab format to a flipped-classroom format. The use of lectures has been reduced while the use of tutorials and practical exercises has increased. Primary learning is now accomplished by watching videos prepared by the lecturer and studying the textbook.Offering this course for several years by distance education made this process considerably easier. Most of the educational "infrastructure" was already in place, and the course's delivery to a non-classroom cohort was already established. Thus many elements of the new structure did not have to be produced from scratch. Improvements to the course website and all the course material has benefited all students, both online and on-campus.The new course structure was delivered for the first time in 2014, has run for two semesters, and will continue in 2015. Student learning and performance is being measured by assignment and exam marks for both on-campus and off-campus students. Students are also surveyed to gauge how well they received the new innovations, especially the video presentations on the lab experiments. It was found that student performance in the new structure was no worse than that in the older structure (average on-campus grades increased 10%), and students in general welcomed the changes. Similar transitions are being implemented in other courses in Deakin's engineering degree program.This presentation will show how physics is taught to online students, outline the changes made to support flipping the on-campus classroom, and how that process benefited the off-campus cohort.