Variation of fibre diameter coefficient of variation and fibre curvature across mohair fleeces: Implications for animal selection, genetic selection and fleece evaluation

The presentwork aimed to determine howthe average fibre diameter coefficient of variation (CVD) and fibre curvature (FC) differences between nine sampling sites vary between sex and flock, to identify differences in variability between sampling sites as a result of between animal and between sire variability and to determine correlations between sampling sites in between animal and between sire variability. Australian Angoras (n = 313) from two farms in southern Australia were sampled at 12 and 18 months of age at nine sites (mid side, belly, brisket, hind flank, hip, hock, mid back, neck, shoulder). Staples were taken prior to shearing at skin level and CVD and FC determined. For each shearing, differences in CVD and FC between sampling sites, how these differences were affected by farm, sex, and sire, and the covariance between sites for sire and individual animal effects were investigated by restricted maximum likelihood (REML) analyses. The median mid side CVD at 12 and 18 months of age ranged from 23.6 to 25.1% but the actual range was 16.8–34.2%. The median mid side FC at 12 and 18 months of age ranged from 14.4 to 18.6◦/mm but the actual range was 10.5–26.3◦/mm. The general pattern for CVDwas for the mid back, hip and neck sites to have similar CVD, the brisket, hind flank and hock sites to have larger CVD and the belly to have smaller CVD than the mid side site. The between animal variation for CVD was lowest at the mid back site. This implies that the mid back would be the most effective site for between animal selection for CVD. Heritabilities for CVD (range at 18 months 0.18–0.30) were only about half the heritabilities for mean fibre diameter in the same study. There was a marked anterior–posterior increase in FC at both farms and with both ages. The results give no clear indication of the best site for between animal selection for FC, other than that the hock should be avoided. Heritabilities for FC are moderate to high (range at 18 months 0.44–0.77) and the genetic correlations are high except for the hock. Thus genetic selection for FC at any site, other than the hock, should be effective for changing FC over the entire fleece. There was more variability between animals than between sites and sires. These results are put into context with associated research on variation in mean fibre diameter and staple length.

Sources of variation in fibre diameter attributes of Australian alpacas and implications for fleece evaluation and animal selection

Sources of variation in fibre diameter attributes of Australian alpacas and implications for fleece evaluation and animal selection were investigated using data collected in the years 1994–97, from 6 properties in southern Australia. Data were analysed using REML (multiple regression analysis) to determine the effect on mean fibre diameter (MFD) and coefficient of variation of MFD (CV(FD)) of age, origin (property), sex (entire male, female), breed (Huacaya, Suri), liveweight, fibre colour, individual, and interactions of these effects. The mean (n = 100) age (range) was 4.2 years (0.1–11.9), liveweight 72.0 kg (12.0–134 kg), MFD 29.1 μm (17.7–46.6 μm), CV(FD) 24.33% (15.0–36.7%).

A number of variables affected MFD and CV(FD). MFD increased to 7.5 years of age, and correlations between MFD at 1.5 and 2 years of age with the MFD at older ages were much higher than correlations at younger ages. Fibre diameter 'blowout' (increase with age) was positively correlated with the actual MFD at ages 2 years and older. There were important effects of farm, and these effects differed with year and shearing age. Suris were coarser than Huacayas with the effect reducing with increased liveweight; there was no effect of sex. Fleeces of light shade were 1 μm finer than dark fleeces. CV(FD) declined rapidly between birth and 2 years of age, reaching a minimum at about 4 years of age and then increasing; however, CV(FD) measurements on young animals were very poor predictors of CV(FD) at older ages, and the response of CV(FD) to age differed with farm and year. Suris had a higher CV(FD) than Huacayas on most properties, and MFD, liveweight, and sex did not affect CV(FD). Fleeces of dark shade had higher CV(FD) than fleeces of light shade in 2 of the years. It is concluded that there are large opportunities to improve the MFD and CV(FD) of alpaca fibre through selection and breeding. The potential benefit is greatest from reducing the MFD and CV(FD) of fibre from older alpacas, through reducing the between-animal variation in MFD and CV(FD). Sampling alpacas at ages <2 years is likely to substantially decrease selection efficiency for lifetime fibre diameter attributes.

Sources of variation contributing to production and quality attributes of Kyrgyz cashmere in Osh and Naryn provinces : implications for industry development

We aimed to quantify the sources of variation contributing to the production and quality of cashmere produced in five districts in Osh and Naryn provinces of Kyrgyzstan. In early spring 2008 mid-side cashmere samples were taken from 719 cashmere adult females, and 41 cashmere adult males and castrates. Samples came from 53 villages and a total of 156 farmers’ flocks. For 91 goats from 33 farmers in 13 villages of two districts that had been sampled earlier, cashmere was combed from the goat at the time of a second visit (end of April 2008) when the cashmere would normally be harvested. Following standard cashmere objective measurement, data were examined using general linear modelling to quantify the effects of potential determinants. The mean fibre diameter (MFD) of cashmere differed between provinces (Osh 15.7 μm, Naryn 16.7 μm; P = 4.4 × 10−20). About 42% of the cashmere was <16 μm, 48% was 16.0–18.0 μm and 9.5% was >18.0 μm. Most of the cashmere samples were coloured (81%), with 63% black and 19% white. The percentage of cashmere samples that were white declined as MFD increased (26% < 14 μm to 11% of >18 μm). The primary determinants of cashmere MFD of individual goats were age of goat (range 1.46 μm, P = 1.8 × 10−12) and farm (range 6.5 μm, P = 1.7 × 10−14). The lesser effects detected for sex (range 0.9 μm, P = 0.026) and colour of cashmere (range 1.8 μm, P = 0.023) were based on small sample sizes and are unreliable. Age of goat had important affects on fibre diameter variation (up to 1.7% in coefficient of variation, P = 5.8 × 10−6) and fibre curvature (2.5–5°/mm, P = 2.1 × 10−4). By far the greatest effect on fibre curvature was cashmere MFD (P = 3.0 × 10−104) with a smaller effect of sex (about 5°/mm, P = 3.0 × 10−6). Village effects were detected on fibre diameter variability (range 4.5% in coefficient of variation, P = 0.027) and fibre curvature (range 15°/mm, P = 1.6 × 10−7). There was a strong negative association between increasing MFD and declining fibre curvature (−5.11 ± 0.181°/mm per 1 μm; P = 7.1 × 10−121; r2 = 0.51). Average combed cashmere weight was 164 g, the clean cashmere content was 0.661 and median clean cashmere production was 110 g per goat (range 60–351 g). Combed cashmere production increased with altitude of the village, probably related to different moulting times as spring temperatures warmed up later in higher altitude villages up to 3200 masl. Measurements of combed cashmere MFD were coarser than the mid-side samples taken earlier in the year. There are farmers and cashmere goats in the sampled districts of Kyrgyzstan which produce the finest qualities of commercial cashmere as the vast majority of cashmere is fine, has low variation in fibre diameter and has fibre crimping (curvature) typical of Chinese and Mongolian cashmere. There is substantial scope to increase the production and commercial value of cashmere produced by Kyrgyz goats. In particular, some villages and farmers need to change their buck selection practices if they wish to produce acceptable cashmere. Farmers should separate their finer and white cashmere prior to sale.

Contribution of objective and subjective attributes to the variation in the whiteness and brightness of commercial mohair sale lots

Colour properties are measured prior to the sale of merino wool as they are of commercial importance when greasy wool is sold and when wool is dyed. With the paucity of knowledge of the colour properties of commercial mohair, this study aimed to identify and quantify the factors affecting the brightness (Y) and yellowness (Y-Z) values of commercial lots of Australian mohair. The research database comprised 520 sale lots (>500,000 kg mohair), which had tristimulus tests, and was sold during the period 2001–2009. Mohair was subjectively classed and sale lots objectively tested using international standard methods for mean fibre diameter (MFD, μm), fibre diameter coefficient of variation (%), International Wool Testing Organization (IWTO) clean wool base (IWTO yield, %w/w), vegetable matter (VM, %w/w) and the tristimulus values X, Y and Z (T units). The tristimulus values of Australian mohair were affected by the objective measurements of MFD, VM%, the subjective classing of stain, cotting, kemp and length and by the year and selling season. Variation in Y was more easily predicted with 90.5% of variance explained by the best model compared with variation in Y-Z, where the best model explained 51.6% of the total variance. Visually assessed properties of the mohair were very important in separating mohair of different Y properties, accounting for almost 80% of the total variance, but were far less important in accounting for the variance in Y-Z, accounting for about 9–10% of the total variance. The most important effects on the Y of mohair were associated with subjectively determined fault categories determined before the sale of mohair. In particular, stain fault explained about two-thirds of the variance in brightness of mohair sale lots. Stained mohair had much lower brightness than mohair free of stain but stain fault explained very little of the variation in yellowness of mohair sale lots. The extent of the differences in tristimulus values between seasons and years were not large for Y but were more important for yellowness (Y-Z), and these effects are likely to be of commercial importance. Generally, brightness decreased and yellowness increased as MFD increased up to about 30 μm. Both cotting and kemp fault were associated with reduced brightness and increased yellowness. The effects of VM% on tristimulus values were small. IWTO yield was associated with changes in tristimulus values, but in the best model, IWTO yield was not a significant determinant. This study indicates that commercial Australian fleece (nonfaulted) mohair was essentially white. Faulted mohair on the other hand exhibited poorer colour characteristics. The mohair subjectively identified as stained prior to sale comprised all the mohair which would be regarded as not white, and this investigation indicates that the effect of staining is on the brightness of mohair rather than the Y-Z measurement. Unlike the situation with merino wool, there was little relationship between the naturally occurring contaminants, as measured by the IWTO washing yield, and either Y or Y-Z.

Correlating the fineness and residual gum content of degummed hemp fibres

It is well known residual gum exists in degummed or retted hemp fibres. Gum removal results in improvement in fibre fineness and the properties of the resultant hemp yarns. However, it is not known what correlation if any exists between the residual gum content in retted hemp fibres and the fibre fineness, described in terms of fibre width in this paper. This study examined the mean width and coefficient of variation (CV) of fibre width of seventeen chemically retted hemp samples with reference to residual gum content. The mean and CV of fibre width were obtained from an Optical fibre diameter analyser (OFDA 100). The linear regression analysis results show that the mean fibre width is directly proportional to the residual gum content. A slightly weaker linear correlation also exists between the coefficient of variation of fibre width and the residual gum content. The strong linear co-relation between the mean of fibre width and the residual gum content is a significant outcome, since testing for fibre width using the OFDA is a much simpler and quicker process than testing the residual gum content. Scanning Electron Microscopy (SEM) reinforces the OFDA findings. SEM micrographs show a flat ribbon like fibre cross-section hence the term “fibre width” is used instead of fibre diameter. Spectral differences in the untreated dry decorticated skin samples and chemically treated and subsequently carded samples indicate delignification. The peaks at 1370 cm⁻¹, 1325 cm⁻¹, 1733 cm⁻¹, and 1600 cm⁻¹ attributed to lignin in the untreated samples are missing from the spectra of the treated samples. The spectra of the treated samples are more amine-dominated with some of the OH character lost.

Evaluation of the fineness of degummed bast fibers

Fiber fineness characteristics are important for yarn production and quality. In this paper, degummed bast fibers such as hemp, flax and ramie have been examined with the Optical Fiber Diameter Analyzer (OFDA100 and OFDA2000) systems for fiber fineness, in comparison with the conventional image analysis and the Wira airflow tester. The correlation between the results from these measurements was analysed. The results indicate that there is a significant linear co-relation between the fiber fineness measurement results obtained from those different systems. In addition, the mean fiber width and its coefficient of variation obtained from the OFDA100 system are smaller than those obtained from the OFDA2000 system, due to the difference in sample preparation methods. The OFDA2000 system can also measure the fiber fineness profile along the bast fiber plants, which can be useful for plant breeding.

Application of bending under tension test to determine the effect of tool radius and the contact pressure on the coefficient of friction in sheet metal forming

To quantify the frictional behaviour in sheet forming operations, several laboratory experiments which simulate the real forming conditions are performed. The Bending Under Tension Test is one such experiment which is often used to represent the frictional flow of sheet material around a die or a punch radius. Different mathematical representations are used to determine the coefficient of friction in the Bending Under Tension Test. In general the change in the strip thickness in passing over the die radius is neglected and the radius of curvature to thickness ratio is assumed to be constant in these equations. However, the effect of roller radius, sheet thickness and the surface pressure are also omitted in some of these equations. This work quantitatively determined the effect of roller radius and the tooling pressure on the coefficient of friction. The Bending Under Tension Test was performed using rollers with different radii and also lubricants with different properties. The tool radii were found to have a direct influence in the contact pressure. The effect of roller radius on friction was considerable and it was observed that there is a clear relationship between the contact pressure and the coefficient of friction.

The influence of reduced flow during a drought on patterns of variation in macroinvertebrate assemblages across a spatial hierarchy in two lowland rivers

1. With the aim of determining whether patterns of variation in macroinvertebrate assemblage composition across the hierarchy of spatial units in two lowland rivers changed during a supra-seasonal drought (1997–2000), patterns during a reduced flow season (1999–2000) were compared with those during two preceding higher flow seasons (1997–98 and 1998–99) using samples from the Glenelg and Wimmera Rivers, two lowland regulated rivers in western Victoria, Australia.

2. We hypothesised that (i) differences between reaches would increase during the reduced flow season owing to decreased hydrological connectivity, (ii) differences between the habitats would decrease because the cessation of flow in run habitats should cause them to become more similar to pool habitats and (iii) differences between microhabitats would also decrease because of reduced scour of inorganic substrata and large woody debris.

3. During each season, macroinvertebrates were sampled from three microhabitats (sand/silt substratum, large woody debris and macrophytes) that were hierarchically nested within a run or pool habitat and within one of three reaches within each river. A range of physico-chemical variables was also sampled.

4. Analysis of similarity showed that assemblage composition in both rivers during the higher flow seasons differed more among microhabitats than other spatial units. However, during the reduced flow season, assemblage composition in the Wimmera River differed most among reaches. This change in pattern was associated with the combined effects of decreased flow and longitudinal increases in salinity. In contrast, the fauna of the Glenelg River appeared to be resistant to the effects of the reduced flow season, owing to limited decline in water quality despite lower river discharge.

5. As salinisation and poor water quality in the Wimmera River result from human activities in the catchment, these results support the idea that human impacts on rivers can change macroinvertebrate scaling patterns and exacerbate the effects of drought beyond the tolerance of many riverine macroinvertebrates.

Performance of statistical inference for block classification in reducing blocking artefact in video coded images

This paper presents a performance study of four statistical test algorithms used to identify smooth image blocks in order to filter the reconstructed image of a video coded image. The four algorithms considered are the Coefficient of Variation (CV), Exponential Entropy of Pal and Pal (E), Shannon's (Logarithmic) Entropy (H), and Quadratic Entropy (Q). These statistical algorithms are employed to distinguish between smooth and textured blocks in a reconstructed image. The linear filtering is carried out on the smooth blocks of the image to reduce the blocking artefact. The rationale behind applying the filter on the smooth blocks only is that the blocking artefact is visually more prominent in the smooth region of an image rather than in the textured region.

Modeling the tensile strains of non-uniform fibers

The maximum strain experienced by the thinnest segment of a non-uniform fiber governs fiber breakage, yet this maximum strain can not be obtained from a normal single fiber test. Only the average strain of the whole fiber specimen can be obtained from a normal single fiber tensile test. This study has examined the relationship between the average strain, the maximum strain and the degree of fiber non-uniformity, expressed in coefficient of variation (CV) of fiber diameters along fiber length. The tensile strain of irregular fibers has been simulated using the finite element method (FEM). Using this method, average and maximum tensile strains of non-uniform fibers were calculated. The results indicate that for irregular fibers such as wool, there is an exponential relationship (i.e.ɛ _ave ɛ _max=ae ^{−b CV} ) between the ratio of average breaking strain and maximum breaking strain (ɛ _ave ɛ _max) and the along-fiber diameter variation (CV). The strain ratio decreases with the increase of the along-fiber diameter variation.

Evaluation of bast fibre retting systems on hemp

In this paper the effect of eight different retting methods on decorticated hemp skins were analyzed. The methods were taken from six publications that looked at the retting of different bast fibres such as ramie, flax and kenaf. The fibres were batch retted in a package dye-vat at 100oC under 2 bar of pressure. The rinsed fibres were opened twice using a Shirley cotton trash separator. The opened fibre was assessed for fibre width, fibre width variation, colour and handle. It was found that the fibre that had undergone chemical retting with 7% Sodium Hydroxide (NaOH) and 0.5% Sodium Sulphite (Na2SO3) had the best diameter (18.39 micron) and the best coefficient of variation of diameter (57.32%). The fibre that was processed with 7% Sodium Hydroxide (NaOH) and 0.5% Sodium Sulphite (Na2SO3) had the whitest colour (YI D1925 = 31.61). The method treated with 1% Sodium Hydroxide (NaOH) and 1% Sodium Sulphite (Na2SO3) had the softest handle and the method treated with 1% Sodium Hydroxide (NaOH) and pre-rinsed with 0.3% Hydrochloric Acid (HCl) showed the best conversion of decorticated skins into spin able fibre (33.9% of dry green skins). It was decided that method treated with 1% Sodium Hydroxide (NaOH) and pre-rinsed with 0.3% Hydrochloric Acid (HCl) had the best fineness of fibre micron, conversion to spin able fibre (33.9% of dry green skins), whitest colour (YI D1925 = 36.13) and softest handle for the cost of chemicals involved.

Examination of EMG normalisation methods for the study of the posterior and posterolateral neck muscles in healthy controls

The purpose of this study was to examine the reliability of normalisation methods used in the study of the posterior and posterolateral neck muscles in a group of healthy controls. Six asymptomatic male subjects performed a total of 12 maximum voluntary isometric contractions (MVIC) and 60%-submaximal isometric contractions (60%-MVIC) against the torque arm of an isokinetic dynamometer whilst surface and intramuscular electromyography (EMG) was recorded unilaterally from representative posterior and posterolateral locations. Reliability was calculated using intra-class correlation coefficient (ICC), relative standard error of measurement (%SEM) and relative coefficient of variation (%CV). Maximal torque output was found to be highly reliable in the directions of extension and right lateral bending when the first of three MVIC contractions was excluded. When averaged across contraction direction, high reliability was found for both surface (MVIC: ICC = 0.986, %SEM = 7.5, %CV = 9.2; 60%-MVIC: ICC = 0.975, %SEM = 10, %CV = 13.7) and intramuscular (MVIC: ICC = 0.910, %SEM = 20, %CV = 19.1; 60%-MVIC: ICC = 0.952, %SEM = 16.5, %CV = 13.5) electrodes. Intramuscular electrodes displayed the least reliability in right lateral bending. The use of visual feedback markedly increased the reliability of 60%-MVIC contractions.

Improvement in mechanical properties of aluminum polypropylene composite fiber

Aluminum particles (Al) were added to polypropylene (PP) in the presence of poly ethylene glycol (PEG) and polypropylene-graft-maleic anhydride to produce composites. The composites were then melt-spun into a mono filament and tested for tensile properties, diameter evenness and morphology. Melt rheological properties of Al/PP composites were studied in linear viscoelastic response regions. It was observed that level of dispersion of aluminum particles within a polypropylene composite fiber could be improved by incorporating polyethylene glycol. The improvement of dispersion led to an improvement in the fibers mechanical properties through a reduction of the coefficient of variation of fiber diameter.