Epitaxial growth of multi-structure sno2 by chemical vapor deposition

The nanowire and whisker heterostructures of tin dioxide were fabricated by the chemical vapor deposition technique. It was demonstrated that various structures of tin oxide can be obtained by controlling the thickness of gold layer and the partial pressure of source vapor at growing sites. 12.5 and 25 nm thicknesses are preferable for the epitaxial growth of nanowires and heterostructure through vapor-liquid-solid mechanism, respectively. The tin dioxide whiskers with core-shell structure were fabricated by vapor-solid mechanism. Meanwhile, the influences of various factors on the tin dioxide growth are also discussed.

An investigation of tribological properties of CN and TiCN coatings

Today the tool industry on a worldwide basis uses hard, wear-resistant, and low-friction coatings produced by different processes such as electrochemical or electroless methods, spray technologies, thermochemical, chemical-vapor deposition (CVD), and physical vapor deposition (PVD). In the current work, two different coatings, nitrocarburized (CN) and titanium carbonitride (TiCN) on M2-grade tool steel, were prepared by commercial diffusion and PVD techniques, respectively. Properties such as thickness, roughness, and hardness were characterized using a variety of techniques, including glow-discharge optical emission spectrometry (GD-OES) and scanning electron microscopy (SEM). A crossed-cylinders wear-testing machine was used to investigate the performances of both coatings under lubrication. The effect of coatings on the performance of lubricants under a range of wear-test conditions was also examined. Degradation of lubricants during tribological testing was explored by Fourier transform infrared (FTIR) spectroscopy.

High N-content holey few-layered graphene electrocatalysts: Scalable solvent-less production

Few layered nitrogen doped graphene (NG) attracts great interest in energy storage and conversion applications due to its electronic and catalytic properties. However, its bulk production cannot be envisioned by the current synthetic methods. Here we report a facile, solvent-less, low cost and high yield process for the synthesis of NG. Mechanochemical solid-state exfoliation allows scalable synthesis of holey and crumple nitrogen-doped few-layered graphene from graphite with controlled high concentration N doping and a high surface area through ball-milling. By adjusting the ratio of starting materials, the nitrogen content can be modulated from 4.87 to 17.83 at.%. Furthermore, the types of nitrogen-containing species in few-layered graphene can also be controlled. The resultant NG exhibits superior oxygen reduction reaction performance and more reliable stability than commercial Pt/C catalysts. This journal is

The reduction of oxygen on iron(II) oxide/poly(3,4-ethylenedioxythiophene) composite thin film electrodes

© 2014 Elsevier Ltd. All rights reserved. Conducting polymers (CPs) are currently being investigated for use in many applications owing to their abilities to catalyze a wide range of electrochemical reactions and act as an effective electrode support for various inorganic and organic electrocatalyst materials. Here, we have found that the deposition of poly(3,4-ethylenedioxythiophene) (PEDOT) through the use of an established base-inhibited chemical vapor-phase polymerization (VPP) procedure using an iron(III) tosylate oxidant results in the co-deposition of electrocatalytic iron(II) oxide species within the film. The presence of these species accounts for the 2-electron reduction of hydrogen peroxide that occurs on these electrodes during the series 4-electron oxygen reduction reaction. Furthermore, this realization leads to the possibility of fabricating thin film inorganic/CP composites of various compositions through careful choice of oxidant in a facile, one-step process. A combination of in situ Raman (487.77 nm laser) and in situ UV-Vis spectroscopy was used to probe the oxidation state of PEDOT in the thin film composite electrodes while reducing oxygen in alkaline conditions. These measurements show that the 2-electron electroreduction of hydrogen peroxide (or HO2 -) occurs only on the iron(II) oxide species in a reaction that is facilitated by an effective electron transfer from the delocalized electron orbitals of the PEDOT matrix. This approach could potentially be used in situ to monitor the electrocatalyst/electrode interface quality of conducting polymer-supported electrocatalysts.

Electrostatically confined plasma in segmented hollow cathode geometries for surface engineering

A segmented hollow cathode (SHC) geometry was used for electrostatic confinement of plasma, and surface engineering treatments were conducted in this arrangement. The assessed processes included plasma nitriding, reactive deposition of sputtered material, and deposition of carbonaceous films by plasma-enhanced chemical vapor deposition with a bipolar pulsed-dc power supply on steel substrates. The treated specimens exhibited uniform surface morphology and deposition layers. Characterization techniques included optical microscopy, scanning electron microscopy with energy dispersive X-ray capability, and X-ray diffraction. The advantages and potential applications of the SHC arrangement are discussed in view of these results.

Patterned growth of carbon nanotubes on Si substrates without predeposition of metal catalysts

Aligned carbon nanotubes (CNTs) can be readily synthesized on quartz or silicon-oxide-coated Si substrates using a chemical vapor deposition method, but it is difficult to grow them on pure Si substrates without predeposition of metal catalysts. We report that aligned CNTs were grown by pyrolysis of iron phthalocyanine at 1000 °C on the templates created on Si substrates with simple mechanical scratching. Scanning electron microscopy and x-ray energy spectroscopy analysis revealed that the trenches and patterns created on the surface of Si substrates were preferred nucleation sites for nanotube growth due to a high surface energy, metastable surface structure, and possible capillarity effect. A two-step pyrolysis process maintained Fe as an active catalyst.

Controlled growth of zinc nanowires

Zinc nanowires have been synthesized by heating a mixture of boron and zinc oxide (ZnO) powders at 1050 °C under a nitrogen atmosphere. The influences of the gas flow rate and the substrate character on the nanowire formation were investigated. It was found that higher-flow rate of gas led to the formation of thinner nanowires; while lower-flow rate of gas produced thicker nanowires and even particles due to the higher partial pressure of Zn vapor in this case. Zn nanowires can be produced on alumina and quartz substrates, but not on a stainless-steel substrate under the same or different synthetic conditions. Photoluminescence measurements were conducted on Zn nanowires and particles and weak emission bands at 482 and 493 nm were observed, which may be contributed by the thin ZnO film on the nanowire surface.

Dynamic characteristics and efficiency of a fluidized bed heat treatment process

The dynamic characteristics of gas bubbles in fluidized beds are important to determine the heat and mass transfer rates at component surfaces and the treated profiles of components. They also have great impact on the components’ structural, mechanical and physical properties. However, it has been very difficult to monitor those characteristics dynamically. In this paper, a specifically designed fluidized bed was introduced to facilitate the capturing of its dynamic characteristics and a new video image processing and analysis algorithm was developed. The algorithm is robust and adaptive in terms of locating both bubbles and components in beds with a single or multiple components. It has many advantages in dynamic characterization of gas bubbles and monitoring component treatment. By using this algorithm, the properties of gas bubbles over any period of time can be accurately obtained. This technology will provide a potential on-line dynamic monitoring and quality control system for the chemical heat treatment processes with fluidized beds.

Irrigation with reclaimed water at Portland Aluminium

Through extensive laboratory and field based analysis of soil chemical and physical processes, this research identified and addressed key management issues associated with the sustainable irrigation of municipal wastewater onto sandy water repellent soils, overlaying a shallow aquifer, in an environmentally significant coastal system.

Process-based modelling of mass transport in the subsurface

Modern societies rely on natural water pathways that include subsurface flow of water and dissolved chemicals. The thesis presents a range of numerical and analytical models for simulating physical, chemical and biological processes in the subsurface, including coastal aquifers, the near-surface vadose zone, and solute transport in biogeochemically active aquifers.

One step multifunctional micropatterning of surfaces using asymmetric glow discharge plasma polymerization

Micropatterning of surfaces with varying chemical, physical and topographical properties usually requires a number of fabrication steps. Herein, we describe a micropatterning technique based on plasma enhanced chemical vapour deposition (PECVD) that deposits both protein resistant and protein repellent surface chemistries in a single step. The resulting multifunctional, selective surface chemistries are capable of spatially controlled protein adhesion, geometric confinement of cells and the site specific confinement of enzyme mediated peptide self-assembly.

Corrosion properties of plasma-polymerized methylcyclohexane films using electrochemical methods

Three types of methylcyclohexane (MCH) coating were deposited as interlayer dielectrics on copper using plasma-enhanced chemical vapor deposition (PECVD) at three different RF plasma power levels. The coating performance was then evaluated by an electrochemical im pedance spectroscopy (EIS) and a potentiodynamic polarization test in 3.5 wt.% NaCl solution. An atomic force microscopy (AFM) and Fourier transform infrared reflection (FT-IR) spectroscopy were also conducted to analyze the coatings. The MCH coatings showed a lower corrosion rate than the copper substrate in the potentiodynamic tests. The EIS results showed that the corrosion resistance of the coatings increased with an increasing plasma power. Thus, the MCH films with an increasing plasma power improved the corrosion resistance due to the formation of a low-porosity coating, the enhanced formation of C−H, C−C, and C≡C stretching configurations, and the improved smooth surfaces.

Characterization and tribological performance of Cu-based intermetallic layers

Fluidized bed reactor chemical vapor deposition (FBR-CVD) has been used to enrich the surface of oxygen free high conductivity (OFHC) copper with titanium, silicon and aluminum. This technique enables the production of coherent and adherent intermetallic surface layers of uniform thickness and high hardness. The characterization of the coatings was performed using backscatter scanning electron microscopy (BS-SEM), X-ray diffraction (XRD), glow discharge optical emission spectroscopy (GDOES) and micro-hardness. The tribological properties of the coatings in dry sliding contact with steel were evaluated by pin-on-disc wear testing.

Synthesis and characterization of tin dioxide core-shell structure nanowires

In this study, one-dimensional and quasi-one-dimensional tin dioxide nanowires and nan-owalls were fabricated by the use of the chemical vapor deposition technique. It was demonstrated that the growth and nanostructure of tin oxide can be controlled by varying the thickness of gold layer and the partial pressure of vapor at growing sites. Nanowires with a core-shell structure, i.e., pure tin core and tin oxide shell, were synthesized from C-S_nO₂ powders at a mol ratio of C/S_nO₂=3/5 on both silicon and Lanthanum Strontium Co-balt Ferrite ceramic wafers through the vapor-solid mechanism. The conditions that are favorable to the growth of core-shell structure nanowires are investigated.