Estimating hydrogen sulphide dissipation rate constant under the influence of different chemical dosing

Sewer odour and corrosion is caused by the reduction of sulphide ions and the release of hydrogen sulphide gas (H2S) into the sewer atmosphere. The reduction of sulphide is determined by its dissipation rate which depends on many processes such as emission, oxidation and precipitation that prevail in wastewater environments. Two factors that mainly affect the dissipation of sulphide are sewer hydraulics and wastewater characteristics; modification to the latter by dosing certain chemicals is known as one of the mitigation strategies to control the dissipation of sulphide. This study investigates the dissipation of sulphide in the presence of NaOH, Mg(OH)2, Ca(NO3)2 and FeCl3 and the dissipation rate is developed as a function of hydraulic parameters such as the slope of the sewer and the velocity gradient. Experiments were conducted in a 18m experimental sewer pipe with adjustable slope to which, firstly no chemical was added and secondly each of the above mentioned chemicals was supplemented in turn. A dissipation rate constant of 2×10^-6 for sulphide was obtained from experiments with no chemical addition. This value was then used to predict the sulphide concentration that was responsible for the emission of H2S gas in the presence of one of the above mentioned four chemicals. It was found that the performance of alkali substances (NaOH and Mg(OH)2) in suppressing the H2S gas emission was excellent while ferric chloride showed a moderate mitigating effect due to its slow reaction kinetics. Calcium nitrate was of little value since the wastewater used in this study experienced almost no biological growth. Thus the effectiveness of selected chemicals in suppressing H2S gas emission had the following order: NaOH ≥ Mg(OH)2 ≥ FeCl3 ≥ Ca(NO3)2.

A methodology for simulating hydrogen sulphide generation in sewer network using EPA SWMM

Predicting hydrogen sulphide concentration in sewer network through modelling tools will be beneficial for many stakeholders to design appropriate mitigation strategies. However, the hydrogen sulphide modelling in a sewer network is crucially dependent on the hydraulic modelling of the sewer. The establishment of precise hydrogen sulphide and hydraulic modelling however requires detailed and accurate information about the sewer network structure and the model parameters. This paper outlines a novel approach for the development of hydraulic and hydrogen sulphide modelling to predict the concentration of hydrogen sulphide in sewer network. The approach combines the calculation of wastewater generation and implementation of flow routing on the EPA SWMM 5.0 platform to allow hydrodynamic simulations. Dynamic wave routing is used for hydraulic simulations. It is considered to be the best approach to route existing/old sewer flow. The build-up of hydrogen sulphide model includes the empirical models of hydrogen sulphide generation and emission. Trial of the model was conducted to simulate a sewer network in Seoul, South Korea with some hypothetical data. Further analysis on the use of chemical dosing on the sewer pipe was also performed by the model. Promising results have been obtained through the model, however calibration and validation of the model is required. The presented methodology provides a possibility of the free platform SWMM to be used as a prediction tool of hydrogen sulphide generation. © 2014 © 2014 Balaban Desalination Publications. All rights reserved.

Mitigation strategies of hydrogen sulphide emission in sewer networks - A review

Hydrogen sulphide (H2S) gas emission in sewer networks is associated with several problems including the release of dangerous odour to the atmosphere and sewer pipe corrosion. The release of odour can endanger public health and corrode sewer pipe walls. Sewer corrosion has the potential to cost water utilities millions of dollars to maintain and rehabilitate the affected sewer pipes. Some chemical mitigation strategies to control hydrogen sulphide emission have been introduced. These include but are not limited to the injection of oxygen, magnesium and sodium hydroxide, calcium nitrate and iron salts. The optimisation of the dosing rate and location of each chemical mitigation strategy is required to achieve maximum hydrogen sulphide gas removal efficiency along with cost effectiveness. In this review paper, the five most popular chemical mitigation strategies that were previously mentioned have been investigated and discussed. The article is broken down into three main discussions. Firstly the sewer transformation processes and factors affecting the hydrogen sulphide generation and emission are highlighted. Secondly, comparisons and differences between each selected chemical mitigation strategy as well as its application covered. Finally, the review of the chemical efficiency and cost is conducted by comparing two case studies in controlling the formation of dissolved sulphide. It was found that the injection of oxygen is the cheapest mitigation strategy of hydrogen sulphide gas generation in sewers, but least effective.

In-situ evaluation of predictive models for H₂S gas emission and the performance of optimal dosage of suppressing chemicals in a laboratory-scale sewer

This in-situ analysis quantifies hydrogen sulfide gas emission from a simulated sewerage system, with varying slopes between 0.5% and 1.5%, under the dosing of certain mitigating chemicals. A portable H₂S gas detector (OdaLog) was employed to record the gaseous phase concentration of hydrogen sulfide. The investigation was comprised of three interrelated phases. In the first stage, precision of four prediction models for H₂S gas emission from a laboratory-synthesized wastewater was assessed. It was found that the model suggested by Lahav fitted the experimental results accurately. Second phase explorations included jar tests to obtain the optimal dosage of four hydrogen sulfide suppressing chemicals, being Mg(OH)₂, NaOH, Ca(NO₃)₂, and FeCl₂. In the third stage, the optimal dosage of chemicals was introduced into the experimental sewerage system, with the OdaLog continuously monitoring the H₂S gas emission. According to a baseline (experiments with no chemical addition), it was found that NaOH and Mg(OH)₂ performed very good in mitigating the release of H₂S gas, while Ca(NO₃)₂ was not effective most probably due to the absence of biological activity. Furthermore, interpretation of OdaLog data through the optimum emission prediction model revealed that higher sewer slope led to more emission.

Human Sulfotransferases and Their Role in Chemical Metabolism

Sulfonation is an important reaction in the metabolism of numerous xenobiotics, drugs, and endogenous compounds. A supergene family of enzymes called sulfotransferases (SULTs) catalyze this reaction. In most cases, the addition of a sulfonate moiety to a compound increases its water solubility and decreases its biological activity. However, many of these enzymes are also capable of bioactivating procarcinogens to reactive electrophiles. In humans three SULT families, SULT1, SULT2, and SULT4, have been identified that contain at least thirteen distinct members. SULTs have a wide tissue distribution and act as a major detoxification enzyme system in adult and the developing human fetus. Nine crystal structures of human cytosolic SULTs have now been determined, and together with site-directed mutagenesis experiments and molecular modeling, we are now beginning to understand the factors that govern distinct but overlapping substrate specificities. These studies have also provided insight into the enzyme kinetics and inhibition characteristics of these enzymes. The regulation of human SULTs remains as one of the least explored areas of research in the field, though there have been some
recent advances on the molecular transcription mechanism controlling the individual SULT promoters. Interindividual variation in sulfonation capacity may be important in determining an individual’s response to xenobiotics, and recent studies have begun to suggest roles for SULT polymorphism in disease susceptibility. This review aims to provide a summary of our present understanding of the function of human cytosolic sulfotransferases.

New insights into the fundamental chemical nature of ionic liquid film formation on magnesium alloy surfaces

Ionic liquids (ILs) based on trihexyltetradecylphosphonium coupled with either diphenylphosphate or bis(trifluoromethanesulfonyl)amide have been shown to react with magnesium alloy surfaces, leading to the formation a surface film that can improve the corrosion resistance of the alloy. The morphology and microstructure of the magnesium surface seems critical in determining the nature of the interphase, with grain boundary phases and intermetallics within the grain, rich in zirconium and zinc, showing almost no interaction with the IL and thereby resulting in a heterogeneous surface film. This has been explained, on the basis of solid-state NMR evidence, as being due to the extremely low reactivity of the native oxide films on the intermetallics (ZrO₂ and ZnO) with the IL as compared with the magnesium-rich matrix where a magnesium hydroxide and/or carbonate inorganic surface is likely. Solid-state NMR characterization of the ZE41 alloy surface treated with the IL based on (Tf)₂N− indicates that this anion reacts to form a metal fluoride rich surface in addition to an organic component. The diphenylphosphate anion also seems to undergo an additional chemical process on the metal surface, indicating that film formation on the metal is not a simple chemical interaction between the components of the IL and the substrate but may involve electrochemical processes.

Symmetrically tapered <30-micron-thick quasi-planar Ge waveguides as chemical sensors for microanalysis

Symmetrically tapered planar IR waveguides have been fabricated by starting with a ZnS coated concave piece of single-crystal Ge, embedding it in an epoxide resin as a supporting substrate, and then grinding and polishing a planar surface until the thickness at the taper minimum is <30 μm. Such tapering is expected to enhance a waveguide's sensitivity as an evanescent wave sensor by maximizing the amount of evanescent wave energy present at the thinnest part of the waveguide. As predicted by theory, the surface sensitivity, i.e., the absorbance signal per molecule in contact with the sensing region, increases with decreasing thickness of the tapered region even while the total energy throughput decreases. The signal-to-noise ratio obtained depends very strongly on the quality of the polished surfaces of the waveguides. The surface sensitivity is superior to that obtained with a commercial Ge attenuated total reflection (ATR) accessory for several types of sample, including thin films (<10 ng) and small volumes (<1 μL) of volatile solvents. By using the waveguides, light-induced structural changes in the protein bacteriorhodopsin were observable using samples as small as ∼50 pmol (∼1 μg). In addition, the waveguide sensors can reveal the surface compositions on a single human hair, pointing to their promise as a tool for forensic fiber analysis.

Effect of nano-Al2O3 addition on the densification of YSZ electrolytes

This work investigates the effect of nanosized Al2O3 addition on the sinterability of YSZ electrolyte. (1-x)YSZ + Al2O3 ceramics with compositions x = 0 to 0.01 were prepared by the conventional mixed oxide route from a commercial powder suspension (particle size <50 nm), and sintered at 1200 to 1500 degrees C for 2 hours in air. Densification, phase evolution, and microstructure were characterized by SEM/EDS and XRD. An improvement in sintered density was observed for the samples with 0.2 to 0.5 mol% Al2O3, though depending on the sintering temperature. Only cubic zirconia was detected as crystalline phase, although XRD features suggested chemical interactions depending upon the amount of Al2O3. The grain size of YSZ was homogeneous and no second phase segregation was detected in the tested range of incorporated nano-Al2O3 and sintering temperatures.

Physical, chemical and biological characterization of membrane fouling

In this chapter, advanced characterization of membrane fouling as a diagnostic tool has been summarized to prevent membrane fouling. Physical, chemical and biological analyses as membrane autopsies are mainly utilized to better understand membrane foulant. The physical characterization gives structure, roughness, charge effect, strength and hydrophobicity of membrane fouling. The chemical methods provide qualitative and quantitative measurements of different inorganic and organic matter. The biological properties present the spatial biofilm distribution, structure of dominant microorganisms and isolation and identification of microorganisms. In addition, detailed membrane foulant types are reviewed in terms of structure, roughness, hydrophobicity, charge effect, strength, calcium, magnesium, aluminum, iron, silicate, particle, functional group, biopolymer, humic acid, polysaccharide, structural composition, biofilm structure, microorganism and foulant interaction.

Chemical immobilization of adult female Weddell seals with tiletamine and zolazepam: effects of age, condition and stage of lactation

Background

Chemical immobilization of Weddell seals (Leptonychotes weddellii) has previously been, for the most part, problematic and this has been mainly attributed to the type of immobilizing agent used. In addition to individual sensitivity, physiological status may play an important role. We investigated the use of the intravenous administration of a 1:1 mixture of tiletamine and zolazepam (Telazol®) to immobilize adult females at different points during a physiologically demanding 5–6 week lactation period. We also compared performance between IV and IM injection of the same mixture.
Results

The tiletamine:zolazepam mixture administered intravenously was an effective method for immobilization with no fatalities or pronounced apnoeas in 106 procedures; however, there was a 25 % (one animal in four) mortality rate with intramuscular administration. Induction time was slightly longer for females at the end of lactation (54.9 ± 2.3 seconds) than at post-parturition (48.2 ± 2.9 seconds). In addition, the number of previous captures had a positive effect on induction time. There was no evidence for effects due to age, condition (total body lipid), stage of lactation or number of captures on recovery time.
Conclusion

We suggest that intravenous administration of tiletamine and zolazepam is an effective and safe immobilizing agent for female Weddell seals. Although individual traits could not explain variation in recovery time, we suggest careful monitoring of recovery times during longitudinal studies (> 2 captures). We show that physiological pressures do not substantially affect response to chemical immobilization with this mixture; however, consideration must be taken for differences that may exist for immobilization of adult males and juveniles. Nevertheless, we recommend a mass-specific dose of 0.50 – 0.65 mg/kg for future procedures with adult female Weddell seals and a starting dose of 0.50 mg/kg for other age classes and other phocid seals.

Taking the sting out of darting : Risks, restraint drugs and procedures for the chemical restraint of Southern Hemisphere otariids

The need to manage otariid populations has necessitated the development of a wide range of capture methods. Chemical restraint by remote drug delivery (i.e., darting) is a highly selective method that can be used to facilitate otariid capture in a range of scenarios, when other methods may be impracticable. However, the risks associated with darting otariids are not widely known and guidelines necessary to promote and refine best practice do not exist. We review the risks associated with darting and in light of our findings, develop darting guidelines to help practitioners assess and minimize risks during capture, anesthesia and recovery. Published studies reveal that mortalities associated with darting predominantly result from complications during anesthetic maintenance (e.g., prolonged respiratory depression, apnea, or hyperthermia), rather than from complications during capture or recovery. In addition to monitoring vital signs and proper intervention, the risk of irreversible complications during anesthesia can be reduced by administering drug doses that are sufficient to enable the capture and masking of animals, after which anesthetic depth can be regulated using gas anesthesia.

Addition of biological functionality to poly(epsilon-caprolactone) films

Biodegradable polyesters such as poly(epsilon-caprolactone) (PCL) have a number of biomedical applications; however, their usage is often limited by a lack of biological functionality. In this paper, a PCL-based polymer containing pendent groups activated by 4-nitrophenyl chloroformate (NPC) and reactive toward primary amines has been cast into thin films. The reactivity of the films toward poly(l-lysine) and the cell adhesion peptide, GRGDS, was assessed, and their cell adhesive capabilities were characterized. ATR-FTIR analysis found that NPC functional groups were present on the surface of the cast film, and the synthesis, conjugation, and visualization of a fluorescent molecule on these films further demonstrated the success of this functionalization methodology. The immersion of these films into a solution of either poly(l-lysine) (PLL) or GRGDS in PBS (pH 7.4) and subsequent 3T3 fibroblast adhesion studies demonstrated significant improvement in cell adhesion and spreading over films cast from unmodified PCL. This investigation has shown that this novel NPC-containing polymer can be utilized in many applications where increased cellular adhesion is required, or the coupling of specific molecules to polymer surfaces is of interest.

Addition of low concentrations of an ionic liquid to a base oil reduces friction over multiple length scales: a combined nano- and macrotribology investigation

The efficacy of ionic liquids (ILs) as lubricant additives to a model base oil has been probed at the nanoscale and macroscale as a function of IL concentration using the same materials. Silica surfaces lubricated with mixtures of the IL trihexyl(tetradecyl)phosphonium bis(2,4,4-trimethylpentyl)phosphinate and hexadecane are probed using atomic force microscopy (AFM) (nanoscale) and ball-on-disc tribometer (macroscale). At both length scales the pure IL is a much more effective lubricant than hexadecane. At the nanoscale, 2.0 mol% IL (and above) in hexadecane lubricates the silica as well as the pure IL due to the formation of a robust IL boundary layer that separates the sliding surfaces. At the macroscale the lubrication is highly load dependent; at low loads all the mixtures lubricate as effectively as the pure IL, whereas at higher loads rather high concentrations are required to provide IL like lubrication. Wear is also pronounced at high loads, for all cases except the pure IL, and a tribofilm is formed. Together, the nano- and macroscales results reveal that the IL is an effective lubricant additive - it reduces friction - in both the boundary regime at the nanoscale and mixed regime at the macroscale.

Stabilizing and destabilizing protein surfactant-based foams in the presence of a chemical surfactant: Effect of adsorption kinetics.

Stimuli-responsive protein surfactants promise alternative foaming materials that can be made from renewable sources. However, the cost of protein surfactants is still higher than their chemical counterparts. In order to reduce the required amount of protein surfactant for foaming, we investigated the foaming and adsorption properties of the protein surfactant, DAMP4, with addition of low concentrations of the chemical surfactant sodium dodecylsulfate (SDS). The results show that the small addition of SDS can enhance foaming functions of DAMP4 at a lowered protein concentration. Dynamic surface tension measurements suggest that there is a synergy between DAMP4 and SDS which enhances adsorption kinetics of DAMP4 at the initial stage of adsorption (first 60s), which in turn stabilizes protein foams. Further interfacial properties were revealed by X-ray reflectometry measurements, showing that there is a re-arrangement of adsorbed protein-surfactant layer over a long period of 1h. Importantly, the foaming switchability of DAMP4 by metal ions is not affected by the presence of SDS, and foams can be switched off by the addition of zinc ions at permissive pH. This work provides fundamental knowledge to guide formulation using a mixture of protein and chemical surfactants towards a high performance of foaming at a low cost.