Novel polymer-ceramic composites for protection against ballistic fragments

For the first time, internally reinforced aggregate polymer ceramic composites were evaluated against fragment simulating projectiles (FSPs) of various calibers to investigate their ballistic impact response. Samples were prepared by mechanically mixing B4C and cBN over a range of ratios and combinations with either thermosetting phenolic or epoxy resin and aramid pulp. Dry mixtures were then molded in a closed die using a heated platen press. The resulting tiles were then mounted as ‘‘strike faces’’ to an aramid backing material using an epoxy resin. Backed targets were tested in a fully instrumented firing range against 5.56 mm FSPs to test ballistic limit. A further series of tests using 7.62, 12.5, and 20 mm FSPs was conducted to examine round deformation across a range of fragments calibers. Round deformations were measured after impact and plotted against shot velocity. It was found that the polymer ceramic composite materials were effective round deformers and, like sintered ceramic strike faces, demonstrated improved ballistic performance at an equivalent areal density and impressive multihit capability.

Effect of B4C, TiB2 and ZrSiO4 ceramic particles on mechanical properties of aluminium matrix composites: Experimental investigation and predictive modelling

This paper focuses on the influence of processing temperature and inclusion of micron-sized B4C, TiB2 and ZrSiO4 on the mechanical performance of aluminium matrix composites fabricated through stir casting. The ceramic/aluminium composite could withstand greater external loads, due to interfacial ceramic/aluminium bonding effect on the movement of grain and twin boundaries. Based on experimental results, the tensile strength and hardness of ceramic reinforced composite are significantly increased. The maximum improvement is achieved through adding ZrSiO4 and TiB2, which has led to 52% and 125% increase in tensile strength and hardness, respectively. To predict the effect of incorporating ceramic reinforcements on the mechanical properties of composites, experimental data of mechanical tests are used to create 3 models named Levenberg-Marquardt Algorithm (LMA) neural networks. The results show that the LMA- neural networks models have a high level of accuracy in the prediction of mechanical properties for ceramic reinforced-aluminium matrix composites.

Reliability of performance in repeated sprint cycling tests

We have estimated the reliability of performance in a commonly employed exercise test consisting of repeated sprints on a cycle ergometer. Eight recreationally active young men completed a practice trial and three more trials at 3- to 6-day intervals. Each trial consisted of two bouts of 30-s maximal-effort cycling on an electromagnetically braked cycle ergometer; the bouts were separated by 4 min of rest. The typical (standard) errors of measurement for peak and mean power between trials 2 to 4 were 2.5 and 1.7% respectively for the first bout and 1.9 and 1.8% for the second bout. These errors are substantially less than those in previous reliability studies of single 30-s sprint tests, probably because of differences in quality of ergometer. The typical errors for the difference between bouts (i.e., fatigue) for peak power and mean power were 3.0 and 2.5%, respectively. Typical errors for the average of the two bouts were 1.6 and 1.2% for peak and mean power respectively, which are small enough to give adequate precision for moderate treatment effects in studies with modest sample sizes.

Friction changes during compression tests using tool rotation technique

A compression test with rotating dies was employed to estimate the friction factor between aluminum samples and steel tooling during large plastic deformations. A cylindrical workpiece was compressed under dry and cold conditions. The magnitudes of torque and normal force were measured and
the average friction factor was calculated using the Coulomb friction law. It was found that under certain conditions the friction increased with increasing angular velocity of the die. This finding led to the conclusion that the choice of die rotation speed is important in interpreting the results from the twist compression test.

Application of very-high-frequency (VHF) method to ceramic insulators

A VHF method (30-300 MHz) is applied to identify faults and defects in ceramic insulators. Insulators which exhibit internal cracks and fractures are used as test samples. Different artificial conditions are introduced to the test samples according to the IEC 507 standard under wet and dry conditions. Using a cascading signal processing technique and analysis methods such as FFT and fractal analysis, VHF signals acquired by digital scope are processed and analyzed. This study indicates that the fractal dimension can be used as an effective tool to isolate the common faulty conditions found on the ceramic insulators. The results from this study strongly support the prospect of using a VHF method to monitor the physical condition of ceramic insulators.

Robustness to non-normality of various tests for the one-sample location problem

This paper studies the effect of the normal distribution assumption on the power and size of the sign test, Wilcoxon's signed rank test and the t-test when used in one-sample location problems. Power functions for these tests under various skewness and kurtosis conditions are produced for several sample sizes from simulated data using the g-and-k distribution of MacGillivray and Cannon.

Mechanical properties and energy absorption of ceramic particulate and resin-impregnation reinforced aluminium foams

The mechanical properties of aluminium foams can be improved by matrix reinforcement and resin-impregnation methods. In the present study, aluminium foams were reinforced by both ceramic particulate reinforcing of the aluminium matrix and resin-impregnating pores. The mechanical properties and the energy absorption of the reinforced aluminium foams were investigated by dynamic and quasi-static compression. Results indicated that the ceramic particle additions of CBN, SiC and B4C in aluminium foams increase the peak stress, elastic modulus and energy absorption of the aluminium foams, under both conditions of dynamic and quasi-static compression. Moreover, the aluminium foams with and without ceramic particle additions exhibited obvious strain rate sensitivity during dynamic compression. Furthermore, the resin-impregnation improves the mechanic properties and energy absorption of aluminium foams significantly. However, aluminium foams with resin-impregnation showed negligible strain rate sensitivity under dynamic compression. It is reported that both the ceramic particle addition and resin-impregnation can be effective techniques to improve the mechanical and the energy absorption properties of aluminium foams.

Influence of low-strain deformation characteristics of high strength sheet steel on curl and springback in bend-under-tension tests

The influence of low-strain deformation behavior on curl and springback in advanced high strength steels (AHSS) was assessed using a bend-under-tension test. The effect of yielding behavior on curl and springback was examined by heat-treating two dual-phase steels to induce yield point elongation, while keeping a relatively constant tensile strength and a constant sheet thickness. A dual-phase and TRIP steel with similar initial thickness and tensile strengths were also examined to investigate the effect of work-hardening on curl and springback. It is shown that while current understanding limits prediction of curl and springback in bending under tension using only the initial sheet thickness and tensile strength, both the yielding and work-hardening behavior can affect the results. Explanations for these effects are proposed in terms of the discontinuous yielding and flow stress in the materials.

Mean reversion in stock prices: new evidence from panel unit root tests

Purpose – There are several studies that investigate evidence for mean reversion in stock prices. However, there is no consensus as to whether stock prices are mean reverting or random walk (unit root) processes. The goal of this paper is to re-examine mean reversion in stock prices.
Design/methodology/approach – The authors use five different panel unit root tests, namely the Im, Pesaran and Shin t-bar test statistic, the Levin and Lin test, the Im, Lee, and Tieslau Lagrangian multiplier test statistic, the seemingly unrelated regression test, and the multivariate augmented Dickey Fuller test advocated by Taylor and Sarno.
Findings – The main finding is that there is no mean reversion of stock prices, consistent with the efficient market hypothesis.
Research limitations/implications – One issue not considered by this study is the role of structural breaks. It may be the case that the efficient market hypothesis is contingent on structural breaks in stock prices. Future studies should model structural breaks.
Practical implications – The findings have implications for econometric modelling, in particular forecasting.
Originality/value – This paper adds to the scarce literature on the mean reverting property of stock prices based on panel data; thus, it should be useful for researchers.

Colorectal cancer screening in Australia: an economic evaluation of a potential biennial screening program using faecal occult blood tests

Objective: To evaluate whether the introduction of a national, co-ordinated screening program using the faecal occult blood test represents 'value-for-money' from the perspective of the Australian Government as third-party funder.  Methods: The annual equivalent costs and consequences of a   biennial screening program in 'steady-state' operation were estimated for the Australian population using 1996 as the reference year. Disability-adjusted life years (DALYs) and the years of life lost (YLLs) averted, and the health service costs were modelled, based on the epidemiology and the costs of colorectal cancer in Australia together with the mortality reduction achieved in randomised controlled trials. Uncertainty in the model was examined using Monte Carlo simulation methods. Results: We estimate a minimum or 'base program' of screening those aged 55 to 69 years could avert 250 deaths per annum (95% uncertainty interval 99–400), at a gross cost of $A55 million (95% UI $A46 million to $A96 million) and a gross incremental cost-effectiveness ratio of $A17,000/DALY (95% UI $A13,000/DALY to $A52,000/DALY). Extending the program to include 70 to 74-year-olds is a more effective option (cheaper and higher health gain) than including the 50 to 54-year-olds. Conclusions: The findings of this study support the case for a national program directed at the 55 to 69-year-old age group with extension to 70 to 74-year-olds if there are sufficient resources. The pilot tests recently announced in Australia provide an important opportunity to consider the age range for screening and the sources of uncertainty, identified in the modelled evaluation, to assist decisions on implementing a full national program.

Discriminative ability of functional loading tests for adolescent jumper

Objective: To investigate the reliability and validity of five squat-based loading tests that are clinically appropriate for jumper's knee. The loading tests were step up, double leg squat, double leg squat on a 25-degree decline (decline squat), single leg decline squat, and decline hop. Design: Cross-sectional controlled cohort. Subjects without knee pain comprised controls, those with extensor tendon pain comprised the jumper's knee group. Setting: Institutional athlete study group in Australia. Participants: Fifty-six elite adolescent basketball players participated in this study, thirteen comprised the jumper's knee group, fifteen athletes formed a control group. Intervention: Each subject performed each loading test for baseline and reliability data on the first testing day. Subjects then performed three days of intensive (6 h daily) basketball training, after which each loading test was reexamined. Main outcome measures: Eleven point interval scale for pain. Results: The tests that best detected a change in pain due to intensive workload were the single leg decline squat and single leg decline hop. This study found that decline tests have better discriminative ability than the standard squat to detect change in jumper's knee pain due to intensive training. The typical error for these tests ranged from 0.3 to 0.5, however, caution should be exercised in the interpretation of these reliability figures due to relatively low scores. Conclusions: The single leg decline squat is recommended in the physical assessment of adolescent jumper's knee. The decline squat was selected as the best clinical test over the decline hop because it was easier to standardise performance.