An investigation into the ion-exchange properties of chemically modified wool for use in water treatment and chromatography

This study was undertaken to investigate the suitability of natural and chemically treated wool fibres for use in water treatment and in the separation of constituents for monitoring contaminants in water.

Experimental work was carried out to determine the ability of natural and treated wool fibres to remove these constituents from water,

This study provided information on the characteristics of the wool fibre as a medium in water treatment.

Influence of emulsification on the properties of styrene-butadiene-styrene chemically modified bitumens

The effect of emulsification on the styrene-butadiene-styrene (SBS) chemically modified bitumens (CMBs) is studied by conventional tests, differential scanning calorimetry (DSC) and fourier transform infrared (FTIR) spectroscopy. Compared to CMBs, modified bitumen emulsion residues (MBERs) exhibit higher temperature susceptibility, inferior resistant to cracking and deformation, lower elastic recovery and storage stability whereas these properties are improved substantially relative to base bitumens. DSC results show that the thermostability of CMBs decreased slightly after emulsification which indicate the emulsification exerts very little effect on the thermal property of CMBs. The FTIR results do not indicate any chemical reaction exists on CMBs during the emulsification.

Identification of surface heterogeneity effects in cyclic voltammograms derived from analysis of an individually addressable gold array electrode

Voltammetric behavior at gold electrodes in aqueous media is known to be strongly dependent on electrode polishing and history. In this study, an electrode array consisting of 100 nominally identical and individually addressable gold disks electrodes, each with a radius of 127 µm, has been fabricated. The ability to analyze both individual electrode and total array performance enables microscopic aspects of the overall voltammetric response arising from variable levels of inhomogeneity in each electrode to be identified. The array configuration was initially employed with the reversible and hence relatively surface insensitive [Ru(NH₃)₆]^3+/2+ reaction and then with the more highly surface sensitive quasi-reversible [Fe(CN)₆]^3−/4− process. In both these cases, the reactants and products are solution soluble and, at a scan rate of 50 mV s⁻¹, each electrode in the array is assumed to behave independently, since no evidence of overlapping of the diffusion layers was detected. As would be expected, the variability of the individual electrodesʼ responses was significantly larger than found for the summed electrode behavior. In the case of cytochrome c voltammetry at a 4,4′-dipyridyl disulfide modified electrode, a far greater dependence on electrode history and electrode heterogeneity was detected. In this case, voltammograms derived from individual electrodes in the gold array electrode exhibit shape variations ranging from peak to sigmoidal. However, again the total response was always found to be well-defined. This voltammetry is consistent with a microscopic model of heterogeneity where some parts of each chemically modified electrode surface are electroactive while other parts are less active. The findings are consistent with the common existence of electrode heterogeneity in cyclic voltammetric responses at gold electrodes, that are normally difficult to detect, but fundamentally important, as electrode nonuniformity can give rise to subtle forms of kinetic and other forms of dispersion.

Determination of ascorbic acid by a gold–zinc Oxide Nanoparticle-Modified Glassy carbon electrode

.A novel electrochemical sensing platform was developed based on flower-like gold–zinc oxide core–shell nanoparticles and a graphene nanocomposite-modified glassy carbon electrode. The gold–zinc oxide core–shell nanoflowers were synthesized by seed growth and characterized by high-resolution transmission electron microscopy, energy-dispersive X-ray spectroscopy, and ultraviolet-visible absorption spectroscopy. The modified electrode provided good electrocatalytic properties, rapid response, high stability, and favorable reproducibility for determination of ascorbic acid. The performance of the sensor included a linear dynamic range from 1.0 × 10−7 to 6.0 × 10−4 M, a limit of detection of 3.9 × 10−8 M, and a sensitivity of 24.12 µA/mM. The nanocomposite also provided excellent selectivity and lower potential for the oxidation of ascorbic acid. The sensor was used for the determination of ascorbic acid in tablets with satisfactory results. This device provides rapid, simple, and selective determination of ascorbic acid.

Stepwise synthesis of Gly−Gly−His on gold surfaces modified with mixed self-assembled monolayers

Peptide-modified electrode surfaces have been shown to have excellent recognition properties for metal ions. An efficient method of screening a potential peptide for its selectivity for a given metal would involve the synthesis of the peptide directly on the electrode surface. This paper outlines a procedure in which the tripeptide Gly−Gly−His was synthesized one amino acid at a time on a gold surface modified with a self-assembled monolayer of the mixed alkanethiolates 3-mercaptopropionic acid (MPA) and 3-mercaptopropane (MP). Electrochemistry and high-resolution mass spectrometry were used to elucidate the structure of the adsorbed species and follow the synthesis. The amino acids can be attached only to MPA, but the presence of a diluting unreactive molecule of MP reduces steric crowding about the reaction center. The maximum coverage of synthesized tripeptide occurs at a ratio of MPA/MP of 1:1.

Redox voltammetry of sub-parts per billion levels of Cu2+ at polyaspartate-modified gold electrodes

An electrochemical sensor for the detection of Cu2+ is reported which incorporates poly-l-aspartic acid (PLAsp) with 32–96 aspartate units as a selective ligand for the metal ion. PLAsp is covalently attached to a gold electrode modified with a monolayer of 3-mercaptopropionic acid using carbodiimide coupling via an N-hydroxysuccinimide (NHS) ester intermediate. The acid side groups and deprotonated peptide nitrogens on two aspartate moieties are thought to be primarily responsible for chelation of Cu2+, which remains bound when reduced to Cu+. A consequence of the multiple binding points that are available with a polypeptide is the low detection limit. The lowest concentration detected was 3 nM (0.2 ppb) achieved with Osteryoung square wave voltammetry. This detection limit compares favourably with that of ICP-OES and previously reported cysteine-modified electrodes. Analysis of tap and lake water samples using the PLAsp-modified electrode agreed well with ICP-OES analysis of the same samples.

Flexural characteristics of coir fiber reinforced cementitious composites

This study has examined the flexural properties of natural and chemically modified coir fiber reinforced cementitious composites (CFRCC). Coir fibers of two different average lengths were used, and the longer coir fibers were also treated with a 1 % NaOH solution for comparison. The fibers were combined with cementitious materials and chemical agents (dispersant, defoamer or wetting agent) to form CFRCC. The flexural properties of the composites, including elastic stress, flexural strength, toughness and toughness index, were measured. The effects of fiber treatments, addition of chemical agents and accelerated ageing of composites on the composites’ flexural properties were examined. The results showed that the CFRCC samples were 5–12 % lighter than the conventional mortar, and that the addition of coir fibers improved the flexural strength of the CFRCC materials. Toughness and toughness index, which were associated with the work of fracture, were increased more than ten times. For the alkalized long coir fiber composites, a higher immediate and long-term toughness index was achieved. SEM microstructure images revealed improved physicochemical bonding in the treated CFRCC.

Developing a stakeholder analysis to aid bio-based product innovation

Purpose – The results which that study seeks to report are the first part of a larger research programme funded by the New Zealand Foundation for Research, Science & Technology (FRST) aimed at gaining a better understanding of stakeholder perceptions in relation to bio-based products.

Design/methodology/approach – Utilising three chemically modified wood products, data were collected from focus groups and questionnaires and centred primarily on perceptions surrounding the acceptability of building materials that have been bio-modified. Irrespective of the type of chemical modification, family health and durability were the most important factors identified.

Findings – The study finds that product cost rated lower in the 16 factors evaluated, and energy used in production was of little concern. When comparing the three products to one another, two distinct groups with quite differing purchasing philosophies were identified and these perspectives significantly influenced perceptions of product acceptability and willingness to purchase. Utilising a paired comparison technique, an investigation of trade-offs indicated preference for performance over cost and product familiarity. Similarly, low chemical emissions were also preferred over cost considerations. Among the findings, there was scepticism regarding trust in manufacturers to adequately safeguard health and safety and to have a minimum impact on the environment. Low levels of trust were expressed in regard to manufacturers' concern for future generations.

Originality/value – The paper develops an investigative framework which could be applied to the evaluation of products arising from bio-material technology innovation and recommendations for future research directions.

Exploring the use of the tripeptide Gly–Gly–His as a selective recognition element for the fabrication of electrochemical copper sensors

The modification of electrodes with the tripeptide Gly–Gly–His for the detection of copper in water samples is described in detail. The tripeptide modified electrode was prepared by first self-assembling 3-mercaptopropionic acid (MPA) onto the gold electrode followed by covalent attachment of the tripeptide to the self-assembled monolayer using carbodiimide coupling. The electrodes were characterized using electrochemistry, a newly developed mass-spectrometry method and quantum mechanical calculations. The mass spectrometry confirmed the modification to proceed as expected with peptide bonds formed between the carboxylic acids of the MPA and the terminal amine of the peptide. Electrochemical measurements indicated that approximately half the MPA molecules in a SAM are modified with the peptide. The peptide modified electrodes exhibited high sensitivity to copper which is attributed to the stable 4N coordinate complex the peptide formed around the metal ion to give copper the preferred tetragonal coordination. The formation of a 4 coordinate complex was predicted using quantum mechanical calculation and confirmed using mass spectrometry. The adsorption of the copper to the peptide modified electrode was consistent with a Langmuir isotherm with a binding constant of (8.1 ± 0.4) 1010 M−1 at 25 °C.

A novel non-enzymatic glucose sensor based on nickel (II) oxide electrospun nanofibers

A new enzymeless glucose sensor has been fabricated via electrospinning technology and subsequent calcination. The morphology and structure of the as-prepared nanofibers have been characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The electrocatalytic oxidation of glucose in alkaline medium at nickel oxide modified glassy carbon electrodes has been investigated. The modified electrodes offer excellent electrocatalytic activity toward the glucose oxidation at low positive potential (0.3 V). Glucose has been determined chronoamperometrically at the surface of NiO nanofibers modified electrode in 0.5 mM NaOH. Under the optimized condition, the calibration curve is linear in the concentration range of 2 × 10−3 mM∼1 mM, and 1 mM∼9.5 mM. The detection limit (signal-to-noise 3) and response time are 3.394 × 10−6 M and 2 s, respectively. The NiO electrospun nanofibers is easy to prepare and feasible in economy. The modified electrode is steady and can be used repeatedly, so it is reasonable to expect its broad use in non-enzymatic glucose sensor.

Aptamer therapeutics: the 21st century's magic bullet of nanomedicine

Aptamers, also known as chemical antibodies, are short single-stranded DNA, RNA or peptide molecules. These molecules can fold into complex three-dimensional structures and bind to target molecules with high affinity and specificity. The nucleic acid aptamers are selected from combinatorial libraries by an iterative in vitro selection procedure known as systematic evolution of ligands by exponential enrichment (SELEX). As a new class of therapeutics and drug targeting entities, bivalent and multivalent aptamer-based molecules are emerging as highly attractive alternatives to monoclonal antibodies as targeted therapeutics.

Aptamers have several advantages, offering the possibility of overcoming limitations of antibodies: 1) they can be selected against toxic or non-immunogenic targets; 2) aptamers can be chemically modified by using modified nucleotides to enhance their stability in biological fluids or via incorporating reporter molecules, radioisotopes and functional groups for their detection and immobilization; 3) they have very low immunogenicity; 4) they display high stability at room temperature, in extreme pH, or solvent; 5) once selected, they can be chemically synthesized free from cell- culturederived contaminants, and they can be manufactured at any time, in large amounts, at relatively low cost and reproducibly; 6) they are smaller and thus can diffuse more rapidly into tissues and organs, leading to faster targeting in drug delivery; 7) they have lower molecular weight that can lead to faster body clearance, resulting in a low background noise for imaging and minimizing the radiation dose to the patient in diagnostic imaging. Thus, the high selectivity and sensitivity, ease of screening and production, chemical versatility as well as stability make aptamers a class of highly attractive agents for the development of novel therapeutics, targeted drug delivery vehicles and molecular imaging.

In the review, we will discuss the latest technological advances in developing aptamers, its application as a novel class of drug on its own, as well as in surface functionalization of both polymer nanoparticles or nanoliposomes in the treatment of cancer, viral and autoimmune diseases.

Growth of single-walled carbon nanotubes from well-defined POSS nanoclusters structure

High-quality single-walled carbon nanotubes (SWNTs) with narrow diameter distribution can be generated from well-defined Si8O12 nanoclusters structure which form from thermal decomposition of chemically modified polyhedral oligomeric silsesquioxane (POSS). The nanosized SixOy particles were proved to be responsible for the SWNT growth and believed to be the reason for the narrow diameter distribution of the as-grown SWNTs. This could be extended to other POSS. The SWNTs grown from the nanosized SixOy particles were found to be semiconducting enriched SWNTs (s-SWNTs). A facile patterning technology, direct photolithography, was developed for generating SWNT pattern, which is compatible to industrial-level fabrication of SWNTs pattern for device applications. The metal-free growth together with preferential growth of s-SWNTs and patterning in large scale from the structure-defined silicon oxide nanoclusters not only represent a big step toward the control growth of SWNTs and fabrication of devices for applications particularly in nanoelectronics and biomedicine but also provide a system for further studying and understanding the growth mechanism of SWNTs from nanosized materials and the relationship between the structure of SWNT and nonmetal catalysts.

Differential effects of natural palm oil, chemically and enzymatically-modified palm oil on weight gain, blood lipid metabolites and fat deposition in a pediatric pig model

Background: Increasing prevalence of obesity and overweight in the Western world, continue to be a major health threat and is responsible for increased health care costs. Dietary intervention studies show a strong positive association between saturated fat intake and the development of obesity and cardiovascular disease. This study investigated the effect of positional distribution of palmitic acid (Sn-1, 2 & 3) of palm oil on cardiovascular health and development of obesity, using weaner pigs as a model for young children.

Methods: Male and female weaner piglets were randomly allocated to 4 dietary treatment groups: 1) pork lard (LRD); 2) natural palm olein (NPO); 3) chemically inter-esterified PO (CPO) and 4) enzymatically inter-esterified PO (EnPO) as the fat source. Diets were formulated with 11% lard or with palm olein in order to provide 31% of digestible energy from fat in the diet and were balanced for cholesterol, protein and energy across treatments.

Results: From 8 weeks onwards, pigs on EnPO diet gained (P < 0.05) more weight than all other groups. Feed conversion efficiency (feed to gain) over the 12 week experimental period did not vary between treatment groups. Plasma LDL-C content and LDL-C/HDL-C ratio in pigs fed natural PO tended to be lower compared to all other diets. The natural PO lowered (P < 0.02) the plasma triglyceride (TG) content relative to the lard or EnPO diets, but was not different from the CPO diet. The natural PO diet was associated with lower (P < 0.05) saturated fat levels in subcutaneous adipose tissue than the CPO and EnPO diets that had lower saturated fat levels than the lard diet. Female pigs had lower lean and higher fat and fat:lean ratio in the body compared with male pigs. No difference in weight gain or blood lipid parameters was observed between sexes.

Conclusions: The observations on plasma TG, muscle and adipose tissue saturated fatty acid contents and back fat (subcutaneous) thickness suggest that natural palm oil may reduce deposition of body fat. In addition, dietary supplementation with natural palm oil containing palmitic acid at different positions in meat producing animals may lead to the production of meat and meat products with lower saturated fats. An increase in fat content and a decrease in lean content in female pigs resulted in an increased body fat:lean ratio but gender had no effect on blood lipid parameters or insulin concentrations.

Evidence for the direct interaction between methylene blue and guanine bases using DNA-modified carbon paste electrodes

It is explored that methylene blue interacts with the guanine bases specifically, rather than the bases of ss-DNA in general. This interaction can be used as a method of quantifying the amount of oligonucleotide that is immobilized onto an electrode surface.