Photocatalytic decolorization of lanasol blue CE dye solution using a flat-plate reactor

This paper reports the effectiveness of the photocatalysis TiO₂ in degrading Lanasol Blue CE. A flat-plate reactor (FPR) with a reactor area of 0.37 m² and ultraviolet (UV) light source of six 36 W blacklight lamps was used in the study. Operating variables including dosage of the photocatalyst, flow rates through the FPR, UV intensity, and tilted angle of the reactor were investigated to degrade Lanasol Blue CE. Results showed that the photocatalytic process can efficiently remove the color in textile dyeing effluent. The degradation process was approximated using first-order kinetics. The photocatalytic apparent reaction rate increased with the increasing UV intensity received by the photocatalyst TiO₂ in slurry. The liquid flow rate and tilted angle influenced the film thickness. The apparent reaction rate constant was mainly determined by the liquid film thickness, UV intensity, and the dosage of the photocatalyst. The findings of this research can be utilized as preliminary input for potential solar photocatalytic applications on color removal from dye solutions.

Photocatalytic degradation of dyes in wastewater using TiO2/UV in a flat-plate reactor

The photocatalyst TiO₂ with UV irradiation was used to degrade dyes in textile effluent in a flat-plate photoreactor. A test system was built with the reactor area of 1 x 0.3m2, UV light of six 36W-blacklight. TiO₂ powder P25 with BET surface area 50±15m2/g, average primary particle size 21 nm, purity> 99.5% and content of 83.9% anatase and 16.1 % rutile was used as the photocatalyst. A number of dyes commonly present in dyeing wastewater were tested in this study. The different operating parameters, such as dosage of photocatalyst, the structure of the reactor, flow rates through the flat-plate reactor, UV radiation intensity and tilted angle of the reactor, were investigated. The results showed that the photocatalytic process could efficiently remove most of the colour contained in the dyeing wastewater. It was experimentally observed that first-order kinetics was adequate for characterising the process. The flow rate and the tilted angle had some influence on the film thickness of the fluid in the reactor and the empirical correlation between the film thickness of the fluid and these two parameters was developed. The photoreaction rate was mainly determined by the film thickness of the fluid on the reactor surface and the dosage of the photocatalyst. Optimum operating parameters of the system were found to be at the film thickness of about 1.4mm and a TiO₂ dosage of 1 gIL. The higher the UV intensity, the faster the reaction rate was. The results of these experiments showed that this method has the great potential for colour removal from wastewater at commercial scale.

To overcome the common difficulty of separating the used TiO₂ suspension after treatment precipitation followed with filtration was used in this study to determine the separation efficiencies. On the other hand, TiO₂ in a small pillar shape was also studied for photocatalytic degradation of textile dye effluent. The pillar pellet was made in Oegussa Company, Germany ranging from 2.5 to 5.3mm long and with a diameter of 3.7mm. It was almost pure TiO₂ (83.2% anatase and 16.8% rutile), with a S-content of <20 ppm and a CI content of the order of 0.1 wt. %. No further elements are present in contents above 0.05 wt.%. The TiO₂ pillars were placed on the flat-plate reactor that was divided by the rectangular slots and irradiated under UV light when the treated solution went through the reactor. Four dyes and their mixtures were tested. The results showed that the photocatalytic process under this configuration efficiently remove the colour from textile dyeing effluent, and pillar shape TiO₂ photocatalyst was not dissolved in water and very easy to be separated from solution, enabling it to be reused many times. The first-order kinetics was adequate for characterising the photocatalytic degradation process and the photocatalytic performance was comparable to TiO₂ powder. It is believed that the TiO₂ pellet would be a preferable form of photocatalyst in applications for textile effluent treatment process, and other wastewater treatment processes.

Solar photocatalytic oxidation (PCO) process with a flat-plate reactor

An experimental rig with a flat-plate solar reactor was built to study the effectiveness of degradation using the reactive methylene blue as sensitive objective. The factors that affect the degradation performance, such as dosages of photocatalyst (Ti0₂), initial concentration of reactive methylene blue, flow rate through the flat-plate reactor, solar UV radiation intensity and decolourising efficiency of the solution, have been investigated. The results showed that the solar PCO process with a Flat-plate Reactor could degrade the methylene blue and decolour in methylene blue solution efficiently.

A comparative study of microstructures and mechanical properties obtained by bar and plate rolling

Microstructures and mechanical properties of a low carbon steel were studied after plate rolling and bar rolling. Plate rolling is characterized as a monotonic compressive loading, while bar rolling is characterized as a cross-compressive loading. A four-pass plate rolling and bar rolling experiment was designed so that the material experiences the same amount of strain at each pass during rolling. The rolling experiment was performed at moderately high temperatures (450, 550 and 650 °C). The microstructures and mechanical properties of the low carbon steel acquired from the two types of rolling experiments were compared. The results revealed that differences of loading path attributed by monotonic loading (plate rolling) and cross loading (bar rolling) significantly influenced the microstructures and mechanical properties such as yield stress, ultimate tensile stress, strain hardening exponent and elongation of the low carbon steel.

Nutrient intake and plate waste from an Australian residential care facility

Objective: To determine the plate waste, energy and selected-nutrient intake, from elderly residents living in a high-level care (HLC) and low-level care (LLC) facility.

Design: Three, single, whole day assessments of plate waste, energy, and selected nutrients, using a visual rating plate waste scale.

Setting: Long-term residential care establishment.

Subjects: One hundred and sixty-nine (93 HLC and 76 LLC) individual daily intakes.

Main findings: The mean energy wasted throughout the whole day was 17%. The energy wasted from main meals (16%) was significantly less than the energy wasted at mid-meals (22%, P=0.049). The lowest mean energy wastage occurred at breakfast (8%) compared to lunch (22%) and dinner (25%, P<0.001). The mean (s.d.) daily energy served and consumed was 8.1 (2.0) and 6.6 (2.2) MJ, respectively. There was no difference in energy served or consumed between HLC and LLC residents. On the observation day, 60% of residents consumed less than their estimated energy requirement. The mean calcium intake was 796 (346) mg, and the median (inter-quartile range) vitamin D intake was 1.78 (2.05) μg.

Conclusion: On 1 day, more than half the residents surveyed were at risk of consuming an inadequate energy intake, which over-time, may result in body weight loss. Although wastage was not excessive and energy served was adequate, the amount of food eaten was insufficient to meet energy and calcium requirements for a significant number of residents and it is not possible to consume sufficient vitamin D through food sources.

Laminated plate elements based on higher-order shear deformation theories

Efficient and accurate finite elements are crucial for finite element analysis to provide adequate prediction of the structural behavior. A large amount of laminated plate elements have been developed for finite element analysis of laminated composite plates based on the various lamination theories. A recent and complete review of the laminated finite elements based on the higher-order shear deformation theories, including the global higher-order theories, zig-zag theories and the global-local higher-order theories is presented in this paper. Finally some points on the development of the laminated plate elements are summarized.

Process for the production of ultrafine plate-like alumina particles

A process for producing plate-like alumina particles with a high aspect ratio is described. Nano-sized particles of an aluminium precursor compound, optionally formed by milling, are mixed with a sufficient volume fraction of a diluent and heat treated to form substantially discrete plate-like alpha alumina particles dispersed in the diluent. A mineraliser may be added to lower the effective melting point of the system. Substantially discrete plate-like particles may be formed without agitation when the heat treatment is conducted below the melting point of the diluent.

A simple displacement-based quadrilateral laminated composite plate element - part I : linear analysis

Based on the first-order shear deformation theory (FSDT) and Timoshenko's laminated composite beam functions, a simple displacement-based 4-node, 24-dof quadrilateral laminated plate element is proposed in this paper for linear analysis of thin to moderately thick laminates. The deflection and rotation functions of the element boundary are obtained from the Timoshenko's laminated composite beam functions, hence convergence to the thin plate solution can be achieved theoretically and shear-locking problem is avoided naturally. The in-plane displacement functions of a quadrilateral plane element with drilling degrees of freedom are taken as the in-plane displacements of the proposed quadrilateral element. Some numerical examples of linear analysis of composite laminated plates are calculated, and the results show that the proposed element is convergent, shear-locking free, efficient, accurate and not sensitive to mesh distortion.

A simple displacement-based quadrilateral laminated composite plate element : Part II : linear analysis

The 4-node, 24-dof quadrilateral displacement-based element (Zhang et al. 2004), which have been developed successfully for linear analysis of thin to thick laminated composite plates, is extended further for geometrically nonlinear analysis in this paper. The proposed element is based on the first-order shear deformation theory (FSDT) and von-Karman's large deflection theory, and the total Lagrangian approach is employed to formulate the element. The deflection and rotation functions of the element boundary are obtained from Timoshenko's laminated composite beam functions. The developed element is simple in formulation, free from shear-locking, and include conventional engineering degrees of freedom. Numerical examples demonstrate that the element is accurate and efficient for large deformation, small rotation geometrically nonlinear analysis of thin to moderately thick laminated composite plates.

Process for the production of ultrafine plate-like alumina particles

A process for producing plate-like alumina particles with a high aspect ratio is described. Nano-sized particles of an aluminium precursor compound, optionally formed by milling, are mixed with a sufficient volume fraction of a diluent and heat treated to form substantially discrete plate-like alpha alumina particles dispersed in the diluent. A mineraliser may be added to lower the effective melting point of the system. Substantially discrete plate-like particles may be formed without agitation when the heat treatment is conducted below the melting point of the diluent.

Mid-Holocene (4200 kyr BP) mass mortalities in Mauritius (Mascarenes): insular vertebrates resilient to climatic extremes but vulnerable to human impact

In the light of the currently increasing drought frequency and water scarcity on oceanic islands, it is crucial for the conservation of threatened insular vertebrates to assess how they will be affected. A 4000 yr old fossil assemblage in the Mare Aux Songes (MAS), southwest Mauritius, Mascarene Islands, contains bones of 100 000+ individual vertebrates, dominated by two species of giant tortoises Cylindraspis triserrata and C. inepta, the dodo Raphus cucullatus, and 20 other vertebrate species (Rijsdijk, Hume, Bunnik, Florens, Baider, Shapiro et al. (2009) Mid-Holocene vertebrate bone Concentration-Lagerstätte on oceanic island Mauritius provides a window into the ecosystem of the dodo (Raphus cucullatus). Quaternary Science Reviews 28: 14–24). Nine radiocarbon dates of bones statistically overlap and suggest mass mortality occurred between 4235 and 4100 cal. yr BP. The mortality period coincides with a widely recognized megadrought event. Our multidisciplinary investigations combining geological, paleontological and hydrological evidence suggests the lake was located in a dry coastal setting and had desiccated during this period. Oxygen isotope data from a Uranium-series dated stalagmite from Rodrigues, an island 560 km east of Mauritius, supports this scenario by showing frequently alternating dry and wet periods lasting for decades between 4122 and 2260 cal. yr BP. An extreme drought resulted in falling water-tables at MAS and elsewhere on the island, perhaps deprived these insular vertebrates of fresh water, which led to natural mass mortalities and possibly to extirpations. In spite of these events, all insular species survived until at least the seventeenth century, confirming their resistance to climatic extremes. Despite this, the generally exponential increase of combined human impacts on islands including loss of geodiversity, habitats, and stocks of fresh water, there will be less environmental safe-haven options for insular endemic and native vertebrates during future megadrought conditions; and therefore will be more prone to extinction.

Shear strength of composite plate girders with web cutouts

An experimental investigation of the shear strengths of composite plate girders, with centrally placed rectangular web cutouts, is described. A series of tests is conducted on short‐span girders having conventional welded stud shear connectors, connecting the composite concrete slabs to the top flanges of the plate girders. These tests indicated that it is the tensile or pullout capacity of the connectors that is primarily responsible for sustaining the composite action under predominantly shear loading. Subsequently, a further series of tests is conducted on short‐span girders with bolted tension connectors, designed to offer negligible resistance to horizontal shear forces at the interfaces between the concrete slabs and plate girders, which confirmed the previous conclusion. Both series of tests indicate that if adequate connectors are provided between a plate girder and a composite concrete slab, the shear strength of the composite girder is significantly higher than that of the plate girder alone. A simple analytical model for predicting the shear strengths of composite plate girders is also presented, which shows satisfactory correlation with the test results.