Effect of particle size on the photocatalytic activity of nanoparticulate zinc oxide

In this study, a three-stage process consisting of mechanical milling, heat treatment, and washing has been used to manufacture nanoparticulate ZnO powders with a controlled particle size and minimal agglomeration. By varying the temperature of the post-milling heat treatment, it was possible to control the average particle size over the range of 28–57 nm. The photocatalytic activity of these powders was characterized by measuring the hydroxyl radical concentration as a function of irradiation time using the spin-trapping technique with electron paramagnetic resonance spectroscopy. It was found that there exists an optimum particle size of approximately 33 nm for which the photocatalytic activity is maximized. The existence of this optimal particle size is attributable to an increase in the charge carrier recombination rate, which counteracts the increased activity arising from the higher specific surface area for a sufficiently small particle size.

The importance of particle size in porous titanium and nonporous counterparts for surface energy and its impact on apatite formation

The importance of particle size in titanium (Ti) fabricated by powder metallurgy for the surface energy and its impact on the apatite formation was investigated. Four sorts of Ti powders of different mean particle size were realized through 20 min, 2 h, 5 h and 8 h of ball milling, respectively. Each sort of Ti powder was used to fabricate porous Ti and its nonporous counterparts sharing similar surface morphology, grain size and chemical composition, and then alkali-heat treatment was conducted on them. Surface energy was measured on the surfaces of the nonporous Ti counterparts due to the difficulty in measuring the porous surfaces directly. The surface energy increase on the alkali-heat-treated porous and nonporous Ti was observed due to the decrease in the particle size of the Ti powders and the presence of Ti–OH groups brought by the alkali-heat treatment. The apatite-inducing ability of the alkali-heat-treated porous and nonporous Ti with different surface energy values was evaluated in modified simulated body fluid and results indicated that there was a strong correlation between the apatite-inducing ability and the surface energy. The alkali-heat-treated porous and nonporous Ti discs prepared from the powders with an average particle size of 5.89 ± 0.76 μm possessed the highest surface energy and the best apatite-inducing ability when compared to the samples produced from the powders with the average particle size varying from 19.79 ± 0.31 to 10.25 ± 0.39 μm.

Influence of particle size and size distribution in deep bed filtration and dynamic microfiltration

Particle size and size distribution is an important parameter in solid liquid separation process especially in granular bed filtration and in dynamic microfiltration. This paper discusses their effects on the above processes from extensive experimental data obtained. In granular bed filtration, the experimental results showed that the initial efficiency follows the pattern reported by previous experimental and theoretical studies, i.e., lower efficiency for particles which fall in the range of critical size of 1 m. However, the particle removal during the transient stage increased with an increase in particle size for the range of sizes studied. An attempt was made to quantify these effects in granular bed filtration using semi-empirical approach. In dynamic membrane filtration also, the particle size plays a major role in the retention. However, despite the relative thickness of the membrane (compared to particle size) dynamic microfiltration appears more as a sieving process; the retention is mainly related to the largest pore size.

Wire EDM mechanism of MMCs with the variation of reinforced particle size

The size of reinforced particles notably affects the electro-discharge machining (EDM) of metal matrix composites (MMCs). This paper explores the mechanism of wire EDM of MMCs with different sizes of reinforced particles as well as the corresponding unreinforced matrix material. The mechanisms of material removal, surface generation, and taper kerf formation were investigated. This study shows that the particles’ ability to protect matrix materials from the intense heat of electric arc controls the material removal rate, surface generation, and taper of kerf. The low melting point matrix material is removed very easily, but the heat resistance reinforced particles delay the removal of material and facilitate the transfer of the workpiece material to wire electrode and vice versa. Thus, the material stays longer in touch with intense heat and affects the surface generation, wire electrode wear, and width of the kerf.

Biocompatibility of transition metal-substituted cobalt ferrite nanoparticles

Transition metals of copper, zinc, manganese, and nickel were substituted into cobalt ferrite nanoparticles via a sol-gel route using citric acid as a chelating agent. The microstructure and elemental compositions of the nanoparticles were characterized using scanning electron microscopy combined with energy dispersive X-ray spectroscopy. The particle size of the nanoparticles was investigated using particle size analyzer, and the zeta potentials were measured using zeta potential analyzer. The phase components of the synthesized transition metal-substituted cobalt ferrite nanoparticles were studied using Raman spectroscopy. The biocompatibility of the nanoparticles was assessed using osteoblast-like cells. Results indicated that the substitution of transition metals strongly influences the physical, chemical properties, and biocompatibility of the cobalt ferrite nanoparticles. © 2014 Springer Science+Business Media.

Preparation, characterization and dielectric properties of temperature stable SrTiO3/PEEK composites for microwave substrate applications

Poly(ether ether ketone) (PEEK) is a potential candidate for electronic applications due to its low permittivity, low loss, high melting point, better chemical resistance, excellent insulating properties and easy processibility. Present paper discusses the preparation and characterization of SrTiO3 filled PEEK composite for microwave substrate applications. The dielectric constant, dielectric loss and temperature variation of dielectric constant of the composites have been studied up to 1 MHz using an Impedance Analyzer. Different theoretical approaches have been employed to predict the effective permittivity of composite systems and the results are compared with that of the experimental data. The crystallinity of the bulk composite is studied by X-ray diffraction studies. Scanning electron microscopic technique has been employed to study the dispersion of the particulate filler in PEEK matrix. Vickers hardness of pure and filled PEEK composite has been measured using Microhardness Tester. The effect of particle size on the dielectric as well as mechanical properties of SrTiO3/PEEK composite system is also studied by incorporating micronsize and nanosize fillers. Present study shows that a temperature stable composite can be realized by judiciously selecting appropriate filler concentration in the PEEK matrix.

Equal channel angular pressing of metal matrix composites: effect on particle distribution and fracture toughness

An Al6061-20%Al₂O₃ powder metallurgy (PM) metal matrix composite (MMC) with a strongly clustered particle distribution is subjected to equal channel angular pressing (ECAP) at a temperature of 370 °C. The evolution of the homogeneity of the particle distribution in the material during ECAP is investigated by the quadrat method. The model proposed by Tan and Zhang [Mater Sci Eng 1998;244:80] for estimating the critical particle size which is required for a homogeneous particle distribution in PM MMCs is extended to the case of a combination of extrusion and ECAP. The applicability of the model to predict a homogeneity of the particle distribution after extrusion and ECAP is discussed. It is shown that ECAP leads to an increase of the  uniformity of the particle distribution and the fracture toughness.

Correlation between optical and SEM measurements of wool cortical cell size

Wool fibres consist of micro to nano scale protein constituents that could be used for innovative applications. While techniques for extracting these constituents or making wool fibres into organic powders have been developed, effectively dispersing the particles and accurately determining their size has been difficult in practice. In this study, an ultrasonic method was employed to disperse cortical cells extracted from wool fibres into an
immersion oil or ethanol. Specimens of the cortical cells were then observed under optical microscopy and scanning electron microscopy, respectively. Cell length and maximum cell diameter were measured to quantify the cell size. The results suggest significant discrepancies exist in the cortical cell size obtained from the two different measurement techniques. The maximum diameter of wool cortical cells obtained from the optical microscope was much larger than that from the scanning electron microscope, while the length was much shorter. A correction factor is given so that cortical cell size obtained from the two measurement techniques can be compared.

Low temperature solvothermal synthesis of ZnO quantum dots

ZnO quantum dots were synthesized via a low-temperature solvothermal process without using surfactants. Heat treatment of ZnCl2 and NaOH solutions in tetra-ethylene glycol at 140°C led to the formation of spherical ZnO nanoparticles consisting of the aggregates of uniform-sized quantum dots. The particle size and morphology were characterized using transmission electron microscopy, dynamic light scattering, X-ray diffraction, and Brunauer–Emmett–Teller gas absorption measurements. It was found that the quantum dots in the particles were single crystals of ZnO of ∼5 nm in diameter having the wurtzite structure. The quantum dots showed quantum size effects even in the agglomerated form. The growth mechanism of this new type of ZnO nanoparticles is proposed.

Plane wave scattering by a spherical di-electric particle in motion : a relativistic extension of the Mie theory

Light scattering from small spherical particles has applications in a vast number of disciplines including astrophysics, meteorology optics and particle sizing. Mie theory provides an exact analytical characterization of plane wave scattering from spherical dielectric objects. There exist many variants of the Mie theory where fundamental assumptions of the theory has been relaxed to make generalizations. Notable such extensions are generalized Mie theory where plane waves are replaced by optical beams, scattering from lossy particles, scattering from layered particles or shells and scattering of partially coherent (non-classical) light. However, no work has yet been reported in the literature on modifications required to account for scattering when the particle or the source is in motion relative to each other. This is an important problem where many applications can be found in disciplines involving moving particle size characterization. In this paper we propose a novel approach, using special relativity, to address this problem by extending the standard Mie theory for scattering by a particle in motion with a constant speed, which may be very low, moderate or comparable to the speed of light. The proposed technique involves transforming the scattering problem to a reference frame co-moving with the particle, then applying the Mie theory in that frame and transforming the scattered field back to the reference frame of the observer.

Application of white-beam X-ray microdiffraction for the study of mineralogical phase identification in ancient Egyptian pigments

High-brightness synchrotron X-rays together with precision achromatic focusing optics on beamline 7.3.3 at the Advanced Light Source have been applied for Laue microdiffraction analysis of mineralogical phases in Egyptian pigments. Although this task is usually performed using monochromatic X-ray diffraction, the Laue technique was both faster and more reliable for the present sample. In this approach, white-beam diffraction patterns are collected as the sample is raster scanned across the incident beam (0.8 µm × 0.8 µm). The complex Laue diffraction patterns arising from illumination of multiple grains are indexed using the white-beam crystallographic software package XMAS, enabling a mineralogical map as a function of sample position. This methodology has been applied to determine the mineralogy of colour pigments taken from the ancient Egyptian coffin of Tjeseb, a priestess of the Apis bull dating from the Third Intermediate to Late period, 25th Dynasty to early 26th Dynasty (747 to 600 BC). For all pigments, a ground layer of calcite and quartz was identified. For the blue pigment, cuprorivaite (CuCaSi4O10) was found to be the primary colouring agent with a grain size ranging from ∼10 to 50 µm. In the green and yellow samples, malachite [Cu2(OH)2CO3] and goethite [FeO(OH)] were identified, respectively. Grain sizes from these pigments were significantly smaller. It was possible to index some malachite grains up to ∼20 µm in size, while the majority of goethite grains displayed a nanocrystalline particle size. The inability to obtain a complete mineralogical map for goethite highlights the fact that the incident probe size is considerably larger than the grain size. This limit will continue to improve as the present trend is toward focusing optics approaching the diffraction limit (∼1000× smaller beam area).

The addition of a surfactant at regular time intervals in the mechanical alloying process

The impact of regular additions of a surfactant (ethylene bis-stearamide; EBS) at different time intervals was investigated on the powder characteristics of a biomedical Ti-10Nb-3Mo alloy (wt.%). Ball milling was performed for 10 h on the elemental powders in four series of experiments at two rotation speeds (200 and 300 rpm). The addition of 2 wt.% total EBS at different time intervals during ball milling resulted in noticeable changes in particle size and morphology of the powders. The surfactant addition at shorter time intervals led to the formation of finer particles, a more homogenous powder distribution, a higher powder yield, and a lower contamination content in the final materials. Thermal analysis of the powders after ball milling suggested that differing decomposition rates of the surfactant were responsible for the measured powder particle changes and contamination contents. The results also indicated that the addition of surfactant during ball milling at 200 rpm caused a delay in the alloy formation, whereas ball milling at 300 rpm favored the formation of the titanium alloy.Crown Copyright © 2014 Published by Elsevier B.V. All rights reserved.

Homogeneous isolation of nanocelluloses by controlling the shearing force and pressure in microenvironment

Nanocelluloses were prepared from sugarcane bagasse celluloses by dynamic high pressure microfluidization (DHPM), aiming at achieving a homogeneous isolation through the controlling of shearing force and pressure within a microenvironment. In the DHPM process, the homogeneous cellulose solution passed through chambers at a higher pressure in fewer cycles, compared with the high pressure homogenization (HPH) process. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) demonstrated that entangled network structures of celluloses were well dispersed in the microenvironment, which provided proper shearing forces and pressure to fracture the hydrogen bonds. Gel permeation chromatography (GPC), CP/MAS 13C NMR and Fourier transform infrared spectroscopy (FT-IR) measurements suggested that intra-molecular hydrogen bonds were maintained. These nanocelluloses of smaller particle size, good dispersion and lower thermal stability will have great potential to be applied in electronics devices, electrochemistry, medicine, and package and printing industry. © 2014 Elsevier Ltd.

Optimization of milling parameters on the synthesis of stearic acid coated CaCO3 nanoparticles

Surface modification of precipitated calcium carbonate particles (calcite) in a planetary ball mill using stearic acid as a modification agent for making dispersion in hydrocarbon oil was investigated. Different parameters for processing (milling) such as milling time, ball-to-sample ratio, and molar ratio of the reactant were varied and analyzed for optimization. The physical properties of the hydrophobically modified calcium carbonate particles were measured; the particle size and morphology of the resulting samples were characterized by transmission electron microscopy and X-ray diffraction. The surface coating thickness was estimated using small angle X-ray scattering. © 2014 American Coatings Association & Oil and Colour Chemists' Association.