On the Bauschinger effect in dual phase steel at high levels of strain

The effect of volume fraction and hardness of martensite on the Bauschinger effect in Dual Phase (DP) steel was investigated for strain levels close to those observed in automotive stamping. Five different grades of DP steel were produced by controlled heat treatment allowing the examination of the Bauschinger effect for three different volume fractions of martensite and three levels of martensite hardness. Compression-tension and shear reversal tests were performed to examine the Bauschinger effect at high levels of forming strain. Good correlation between the shear reversal and the compression-tension test was observed suggesting that for DP steel, shear stress strain data, converted to equivalent stress-strain, may be applied directly to characterize kinematic hardening behavior for numerical simulations. Permanent softening was observed following strain reversal and increased with martensite volume fraction and pre-strain level. While the Bauschinger ratio saturates at 3% pre-strain, the Bauschinger strain increases linearly with forming strain without showing saturation. This suggests that to model material behavior accurately in forming processes involving complex loading paths and high levels of strain, test data generated at high strain is required.

On the definition of an kinematic hardening effect graph for sheet metal forming process simulations

The objective of this work is to develop a kinematic hardening effect graph (KHEG) which can be used to evaluate the effect of kinematic hardening on the model accuracy of numerical sheet metal forming simulations and this without the need of complex material characterisation. The virtual manufacturing process design and optimisation depends on the accuracy of the constitutive models used to represent material behaviour. Under reverse strain paths the Bauschinger effect phenomenon is modelled using kinematic hardening models. However, due to the complexity of the experimental testing required to characterise this phenomenon in this work the KHEG is presented as an indicator to evaluate the potential benefit of carrying out these tests. The tool is validated with the classic three point bending process and the U-channel width drawbead process. In the same way, the capability of the KHEG to identify effects in forming processes that do not include forming strain reversals is identified.

A non-associated plasticity model with anisotropic and nonlinear kinematic hardening for simulation of sheet metal forming

A material model for more thorough analysis of plastic deformation of sheet materials is presented in this paper. This model considers the following aspects of plastic deformation behavior of sheet materials: (1) the anisotropy in yield stresses and in work hardening by using Hill's 1948 quadratic yield function and non-constant stress ratios which leads to different flow stress hardening in different directions, (2) the anisotropy in plastic strains by using a quadratic plastic potential function and non-associated flow rule, also based on Hill's 1948 model and r-values, and (3) the cyclic hardening phenomena such as the Bauschinger effect, permanent softening and transient behavior for reverse loading by using a coupled nonlinear kinematic hardening model. Plasticity fundamentals of the model were derived in a general framework and the model calibration procedure was presented for the plasticity formulations. Also, a generic numerical stress integration procedure was developed based on backward-Euler method, so-called multi-stage return mapping algorithm. The model was implemented in the framework of the finite element method to evaluate the simulation results of sheet metal forming processes. Different aspects of the model were verified for two sheet metals, namely DP600 steel and AA6022 aluminum alloy. Results show that the new model is able to accurately predict the sheet material behavior for both anisotropic hardening and cyclic hardening conditions. The drawing of channel sections and the subsequent springback were also simulated with this model for different drawbead configurations. Simulation results show that the current non-associated anisotropic hardening model is able to accurately predict the sidewall curl in the drawn channel sections.

Constitutive modelling of high strength titanium alloy Ti-6Al-4 V for sheet forming applications at room temperature

To enable the design and optimisation of forming processes at room temperature the material behaviour of Ti-6Al-4 V needs to be accurately represented in numerical analysis and this requires an advanced material model. In particular, an accurate representation of the shape and size of the yield locus as well as its evolution during forming is important. In this study a rigorous set of experiments on the quasi-static deformation behaviour of a Ti-6Al-4 V alloy sheet sample at room temperature was conducted for various loading conditions and a constitutive material model developed. To quantify the anisotropy and asymmetry properties, tensile and compression tests were carried out for different specimen orientations. To examine the Bauschinger effect and the transient hardening behaviour in - plane tensile - compression and compression - tensile tests were performed. Balanced biaxial and plane strain tension tests were conducted to construct and validate the yield surface of the Ti-6Al-4 V alloy sheet sample at room temperature. A recently proposed anisotropic elastic-plastic constitutive material model, so-called HAH, was employed to describe the behaviour, in particular for load reversals. The HAH yield surface is composed of a stable component, which includes plastic anisotropy and is distorted by a fluctuating component. The key of the formulation is the use of a suitable yield function that reproduces the experimental observations well for the stable component. Meanwhile, the rapid evolution of the material structure must be captured at the macro - scale level by the fluctuating component embedded in the HAH model. Compared to conventional hardening equations, the proposed model leads to higher accuracy in predicting the Bauschinger effect and the transient hardening behaviour for the Ti-6Al-4 V sheet sample tested at room temperature.