Nucleation sites for ultrafine ferrite produced by deformation of austenite during single-pass strip rolling

An austenitic Ni-30 wt pct Fe alloy, with a stacking-fault energy and deformation characteristics similar to those of austenitic low-carbon steel at elevated temperatures, has been used to examine the defect substructure within austenite deformed by single-pass strip rolling and to identify those features most likely to provide sites for intragranular nucleation of ultrafine ferrite in steels. Samples of this alloy and a 0.095 wt pct C-1.58Mn-0.22Si-0.27Mo steel have been hot rolled and cooled under similar conditions, and the resulting microstructures were compared using transmission electron microscopy (TEM), electron diffraction, and X-ray diffraction. Following a single rolling pass of ∼40 pct reduction of a 2mm strip at 800 °C, three microstructural zones were identified throughout its thickness. The surface zone (of 0.1 to 0.4 mm in depth) within the steel comprised a uniform microstructure of ultrafine ferrite, while the equivalent zone of a Ni-30Fe alloy contained a network of dislocation cells, with an average diameter of 0.5 to 1.0 µm. The scale and distribution and, thus, nucleation density of the ferrite grains formed in the steel were consistent with the formation of individual ferrite nuclei on cell boundaries within the austenite. In the transition zone, 0.3 to 0.5 mm below the surface of the steel strip, discrete polygonal ferrite grains were observed to form in parallel, and closely spaced “rafts” traversing individual grains of austenite. Based on observations of the equivalent zone of the rolled Ni-30Fe alloy, the ferrite distribution could be correlated with planar defects in the form of intragranular microshear bands formed within the deformed austenite during rolling. Within the central zone of the steel strip, a bainitic microstructure, typical of that observed after conventional hot rolling of this steel, was observed following air cooling. In this region of the rolled Ni-30Fe alloy, a network of microbands was observed, typical of material deformed under plane-strain conditions.

Improvement of adhesion of conductive polypyrrole coating on wool and polyester fabrics using atmospheric plasma treatment

In this paper wool and polyester fabrics were pretreated with atmospheric plasma glow discharge (APGD) to improve the ability of the substrate to bond with anthraquinone-2-sulfonic acid doped conducting polypyrrole coating. A range of APGD gas mixtures and treatment times were investigated. APGD treated fabrics were tested for surface contact angle, wettability and surface energy change. Effect of the plasma treatment on the binding strength was analyzed by studying abrasion resistance, surface resistivity and reflectance. Investigations showed that treated fabrics exhibited better hydrophilicity and increased surface energy. Surface treatment by an APGD gas mixture of 95% helium/5% nitrogen yielded the best results with respect to coating uniformity, abrasion resistance and conductivity.

Simulation of the solar adsorption refrigeration operating at near atmospheric pressure

To solve the leaking problem faced by current vacuum adsorption refrigeration systems, the authors have carried out a series of studies on the concept of raising the system's pressure to around atmospheric pressure with an inert gas (eg. Helium) as the pressure-adjusting agent. This paper presents the simulation of the performance oj the activated carbon-methanol adsorption refrigeration operating at near atmospheric pressure powered by solar energy. This simulation can be refereed in the prototype design.

Effects of atmospheric pressure plasma on dye uptake by the surface of wool

A woven pure wool fabric has been exposed to atmospheric pressure plasma for 30 seconds using a pilot-scale. commercial machine. X-ray photoelectron spectral data revealed large increases in oxygen and nitrogen. and a large reduction in carbon. on the surfaces of the plasma-treated fibres. A CIN ratio of 3.55 for plasma-treated wool was consistent with removal of the covalently-bound fatty acids from the surface of the cuticle cells. resulting in exposure of the proteinaceous epicuticle. Dye staining experiments revealed that the back of the fabric had received the same, uniform level of treatment as the face, despite the fact that only the face had been directly exposed to the plasma. Dyes (1 % oww) were applied to fabric at 50°C (liquor ratio =40: 1) and pH values from 3 to 6. The relatively low temperature of 50°C was selected in order to accentuate the effects of plasma on the rate of dye uptake. Under these conditions, dye was adsOibed onto the fibre surfaces, with very little penetration into the fibres. Effects of the plasma treatment on the rate of dyes adsorption were dyespecific. No significant effects of plasma on the rate of dye uptake were observed with relatively hydrophobic dyes, but hydrophilic dyes were adsorbed more rapidly by the plasmatreated fabric. It would appear that for more hydrophobic dyes, hydrophobic effects are more important for the adsorption of dyes by the plasma-treated fibres, even though these fibres were quite hydrophilic. On the other hand. it is concluded that for more hydrophilic dyes, electrostatic effects are more important for adsorption by the plasma-treated fibre.

Nucleation and growth of carbon nanotubes in a mechano-thermal process

Separate nucleation and growth processes of carbon nanotubes were found in a mechano-thermal method in which carbon nanotubes are produced by first mechanical milling of graphite powder at room temperature and subsequent thermal annealing up to 1400 °C. The ball-milled graphite contains nucleation structures (nanosized metal particles and deformed (0 0 2) layers containing pentagons), and disordered carbon as a free carbon atom source. The subsequent annealing activates the growth of two types of multi-walled nanotubes in the absence of carbon vapor. Thin nanotubes (diameter <20 nm) are formed via crystallization of the disordered carbon with the preferred formation of the (0 0 2) basal planes. Thick nanotubes (diameter >20 nm) are formed through a metal catalytic solution–precipitation process (solid–liquid–solid). In both cases, carbon nanotubes grew out from disordered carbon particles with closed tips.

Influence of helium atmospheric plasma treatment on surface and fracture-mechanical behaviour of quickstepTM cured bio-composites

This work investigated the potential of improving flexural properties of natural fiber (jute) reinforced biocomposites by atmospheric pressure helium plasma treatment. Composites were made by the use of combined hand lay-up and vacuum bagging technique followed by newly developed Australia patented Quickstep^TM curing. The physical properties of helium plasma modified fibers were investigated by means of wettability time, coefficient of friction (COF), atomic force microscopy (AFM) and chemical nature of the surface with ATR-FTIR and XPS. There was found a logical correlation between physical and chemical characteristics of the surface of fiber with the fracture mechanical behavior of their resulting biocomposites. In addition, the use of helium atmospheric plasma treatment prior to Quickstep^TM process has proved to be a potential way to positively alter the fracture-mechanical behavior of biocomposites. This study will lead to new commercial applications of natural fiber jute for the composite industry that go beyond wrapping and packaging.

Nucleation and growth during reactions in accumulative roll bonding of Ti/Al multilayers

A two-stage process in the formation of TiAl₃ was found in the accumulative roll bonding (ARB) Ti/Al multilayers. The distribution of layer spacing did not become broad enough to lose the main features of the double exothermal behaviour. A modified model based on thin films was set up to describe the kinetic characteristics of the formation of TiAl₃ in ARB samples.

Combined in situ neutron diffraction and acoustic emission of twin nucleation & twin growth in extruded ZM20 Mg alloy

In the present work in situ neutron diffraction and acoustic emission were used concurrently to study deformation twinning in two ZM20 Mg alloys with significantly different grain sizes at room temperature. The combination of these techniques allows differentionation between the twin nucleation and the twin growth mechanisms. It is shown, that yielding and immediate post-yielding plasticity in compression is governed primarily by twin nucleation, whereas the plasticity at higher strains is governed by twin growth. The current results further suggest that yielding by twinning happens in a slightly different manner in the fine-grained as compared to the coarse-grained alloy.