Performance of smart antennas with receive diversity in wireless sensor networks

In this paper we propose a Geometrically Based Single Bounce Elliptical Model (GBSBEM) for multipath components involving randomly placed scatterers in the scattering region with sensors deployed on a field. The system model assumes a cluster based wireless sensor network (WSN) which collects information from the sensors, filters and modulates the data and transmit it through a wireless channel to be collected at the receiver. We first develop a GBSBE model and based on this model we develop our channel model. Use of Smart antenna system at the receiver end, which exploits various receive diversity combining techniques like Maximal Ratio Combining (MRC), Equal Gain Combining (EGC), and Selection Combining (SC), adds novelty to this system. The performance of these techniques have been proved through matlab simulations and further ahead based on different number of antenna elements present at the receiver array, we calculate the performance of our system in terms of bit-error-rate (BER). Based on the transmission power we quantify for the energy efficiency of our communication model.

On the multicast lifetime of WANETs with multibeam antennas : Formulation, algorithms, and analysis

We explore the multicast lifetime capacity of energy-limited wireless ad hoc networks using directional multibeam antennas by formulating and solving the corresponding optimization problem. In such networks, each node is equipped with a practical smart antenna array that can be configured to support multiple beams with adjustable orientation and beamwidth. The special case of this optimization problem in networks with single beams have been extensively studied and shown to be NP-hard. In this paper, we provide a globally optimal solution to this problem by developing a general MILP formulation that can apply to various configurable antenna models, many of which are not supported by the existing formulations. In order to study the multicast lifetime capacity of large-scale networks, we also propose an efficient heuristic algorithm with guaranteed theoretical performance. In particular, we provide a sufficient condition to determine if its performance reaches optimum based on the analysis of its approximation ratio. These results are validated by experiments as well. The multicast lifetime capacity is then quantitatively studied by evaluating the proposed exact and heuristic algorithms using simulations. The experimental results also show that using two-beam antennas can exploit most lifetime capacity of the networks for multicast communications. © 2013 IEEE.

Performance analysis of receive diversity in wireless sensor networks over GBSBE models

Wireless sensor networks have attracted a lot of attention recently. In this paper, we develop a channel model based on the elliptical model for multipath components involving randomly placed scatterers in the scattering region with sensors deployed on a field. We verify that in a sensor network, the use of receive diversity techniques improves the performance of the system. Extensive performance analysis of the system is carried out for both single and multiple antennas with the applied receive diversity techniques. Performance analyses based on variations in receiver height, maximum multipath delay and transmit power have been performed considering different numbers of antenna elements present in the receiver array, Our results show that increasing the number of antenna elements for a wireless sensor network does indeed improve the BER rates that can be obtained.

Optimal sensor separation for AoA based localization via linear sensor array

This paper investigates the linear separation requirements for Angle-of-Arrival (AoA) sensors, in order to achieve the optimal performance in estimating the position of a target from multiple and typically noisy sensor measurements. We analyse the sensor-target geometry in terms of the Cramer-Rao inequality and the corresponding Fisher information matrix, in order to characterize localization performance with respect to the linear spacial distribution. Here we consider a situation where one sensor is fixed and the rest are free to be positioned in a linear array.

Multi-input-multi-output antennas for radio frequency identification systems

In this chapter the authors discuss the physical insight of the role of wireless communication in RFID systems. In this respect, this chapter gives a brief introduction on the wireless communication model followed by various communication schemes. The chapter also discusses various channel impairments and the statistical modeling of fading channels based on the environment in which the RFID tag and reader may be present. The chapter deals with the fact that the signal attenuations can be dealt with up to some level by using multiple antennas at the reader transmitter and receiver to improve the performance. Thus, this chapter discusses the use of transmit diversity at the reader transmitter to transmit multiple copies of the signal. Following the above, the use of receiver combining techniques are discussed, which shows how the multiple copies of the signal arriving at the reader receiver from the tag are combined to reduce the effects of fading. The chapter then discusses various modulation techniques required to modulate the signal before transmitting over the channel. It then presents a few channel estimation algorithms, according to which, by estimating the channel state information of the channel paths through which transmission takes place, performance of the wireless system can be further increased. Finally, the Antenna selection techniques are presented, which further helps in improving the system performance.

Unicast and broadcast throughput maximization in amplify-and-forward relay networks

Cooperative communication (CC) offers an efficient and low-cost way to achieve spatial diversity by forming a virtual antenna array among single-antenna nodes that cooperatively share their antennas. It has been well recognized that the selection of relay nodes plays a critical role in the performance of CC. Most existing relay selection strategies focus on optimizing the outage probability or energy consumption. To fill in the vacancy of research on throughput improvement via CC, we study the relay selection problem with the objective of optimizing the throughput in this paper. For unicast, it is a P problem, and an optimal relay selection algorithm is provided with a correctness proof. For broadcast, we show the challenge of relay selection by proving it nonprobabilistic hard (NP-hard). A greedy heuristic algorithm is proposed to effectively choose a set of relay nodes that maximize the broadcast throughput. Simulation results show that the proposed algorithms can achieve high throughput under various network settings.

Identification of surface heterogeneity effects in cyclic voltammograms derived from analysis of an individually addressable gold array electrode

Voltammetric behavior at gold electrodes in aqueous media is known to be strongly dependent on electrode polishing and history. In this study, an electrode array consisting of 100 nominally identical and individually addressable gold disks electrodes, each with a radius of 127 µm, has been fabricated. The ability to analyze both individual electrode and total array performance enables microscopic aspects of the overall voltammetric response arising from variable levels of inhomogeneity in each electrode to be identified. The array configuration was initially employed with the reversible and hence relatively surface insensitive [Ru(NH₃)₆]^3+/2+ reaction and then with the more highly surface sensitive quasi-reversible [Fe(CN)₆]^3−/4− process. In both these cases, the reactants and products are solution soluble and, at a scan rate of 50 mV s⁻¹, each electrode in the array is assumed to behave independently, since no evidence of overlapping of the diffusion layers was detected. As would be expected, the variability of the individual electrodesʼ responses was significantly larger than found for the summed electrode behavior. In the case of cytochrome c voltammetry at a 4,4′-dipyridyl disulfide modified electrode, a far greater dependence on electrode history and electrode heterogeneity was detected. In this case, voltammograms derived from individual electrodes in the gold array electrode exhibit shape variations ranging from peak to sigmoidal. However, again the total response was always found to be well-defined. This voltammetry is consistent with a microscopic model of heterogeneity where some parts of each chemically modified electrode surface are electroactive while other parts are less active. The findings are consistent with the common existence of electrode heterogeneity in cyclic voltammetric responses at gold electrodes, that are normally difficult to detect, but fundamentally important, as electrode nonuniformity can give rise to subtle forms of kinetic and other forms of dispersion.

Inhibiting localized corrosion of aluminum and aluminum alloy by rare earth metal compounds : behaviors and characteristics observed using an electrochemically integrated multi-electrode array

An electrochemically integrated multi-electrode array namely the wire beam electrode (WBE) has been used to characterize the behavior of cerium chloride (CeCl3) and lanthanum chloride (LaCl3) in inhibiting localized corrosion of AA2024-T3 and AA1100. CeCl3 has been found to inhibit AA2024-T3 corrosion in 0.005 M sodium chloride (NaCl) solution by suppressing galvanic corrosion activities and by creating a large number of insignificant anodes. It has also been shown to inhibit localized corrosion of AA1100 in 0.5 M NaCl solution by promoting the random distribution of minor anodes. LaCl3 has been found to inhibit localized corrosion of AA2024-T3 at 1000 ppm, although its efficiency dropped significantly when its concentration decreased to 500 ppm. The addition of CeCl3 and LaCl3 to corrosion testing cells at later stages was unable to effectively suppress existing corrosion anodes.

Characterising localised corrosion inhibition by means of parameters measured by an electrochemically integrated multielectrode array

Electrochemical parameters including maximum anodic current density, total anodic current density, the number of anodic sites and the localised corrosion intensity index have been extracted from galvanic current distribution maps that were acquired using an electrochemically integrated multielectrode array, namely, the wire beam electrode. Experiments have been carried out to demonstrate the application of these new electrochemical parameters for characterising localised corrosion inhibition of metals. A typical corrosion inhibitor, potassium dichromate, was found to affect localised corrosion processes in various ways, for instance in sodium chloride solutions, it was found to inhibit localised corrosion of aluminium alloy AA 2024-T3 by suppressing galvanic corrosion activities occurring over the alloy surface, whereas it was found to control localised corrosion of AA 1100 by creating a large number of minor anodes distributing randomly over the metal surface.

Maximum power point tracking of partial shaded photovoltaic array using an evolutionary algorithm: a particle swarm optimization technique

 Partial shading is one of the unavoidable complications in the field of solar power generation. Although the most common approach in increasing a photovoltaic (PV) array’s efficiency has always been to introduce a bypass diode to the said array, this poses another problem in the form of multi-peaks curves whenever the modules are partially shaded. To further complicate matters, most conventional Maximum Power Point Tracking methods develop errors under certain circumstances (for example, they detect the local Maximum Power Point (MPP) instead of the global MPP) and reduce the efficiency of PV systems even further. Presently, much research has been undertaken to improve upon them. This study aims to employ an evolutionary algorithm technique, also known as particle swarm optimization, in MPP detection. VC 2014 Author(s).