Rapid fibre diameter measurement in aqueous solutions with OFDA 2000

In this paper, a new technique has been developed to enable fibre diameters to be measured in an aqueous environment using the OFDA 2000 instrument. The existing OFDA instrument has only been used to measure diameters of animal fibres under dry conditions. This new technique was utilised to assess the effects of pH and temperature on the diameters of merino wool fibres in aqueous environments. Significant changes in fibre diameter under aqueous conditions were found as a function of pH and temperature. Wool fibre diameters were at a minimum close to the wool isoelectric point (pH 4.8) and increased at both lower and higher pHs. Swelling of merino wool fibres was observed to increase linearly by around 15% as the temperature rose from ambient to 70°C.

Benzene adsorption at the aqueous (011) α-quartz interface : is surface flexibility important?

Atomistic simulations of molecular adsorption onto inorganic substrates under aqueous conditions can be used to guide the rational design of new materials, fabricated using biomimetic methods. The success of such work depends critically on the model used. Here, we investigate the impact of using a rigid structural model of the (0 1 1) ?-quartz surface, over a fully flexible model, on the calculated free energy change in the adsorption of a single molecule of benzene (a simple analogue of the amino acid phenylalanine) from liquid water. Subtle differences in the mobility of the adsorbate close to the surface result in the free energy of adsorption being overestimated by the rigid model, relative to the fully flexible case. Moreover, we find that the distribution of bound configurations of the adsorbate at their respective free energy minima is different between the two models.

Structure of arginine overlayers at the aqueous gold interface: implications for nanoparticle assembly.

Adsorption of small biomolecules onto the surface of nanoparticles offers a novel route to generation of nanoparticle assemblies with predictable architectures. Previously, ligand-exchange experiments on citrate-capped gold nanoparticles with the amino acid arginine were reported to support linear nanoparticle assemblies. Here, we use a combination of atomistic modeling with experimental characterization to explore aspects of the assembly hypothesis for these systems. Using molecular simulation, we probe the structural and energetic characteristics of arginine overlayers on the Au(111) surface under aqueous conditions at both low- and high-coverage regimes. In the low-density regime, the arginines lie flat on the surface. At constant composition, these overlayers are found to be lower in energy than the densely packed films, although the latter case appears kinetically stable when arginine is adsorbed via the zwitterion group, exposing the charged guanidinium group to the solvent. Our findings suggest that zwitterion-zwitterion hydrogen bonding at the gold surface and minimization of the electrostatic repulsion between adjacent guanidinium groups play key roles in determining arginine overlayer stability at the aqueous gold interface. Ligand-exchange experiments of citrate-capped gold nanoparticles with arginine derivatives agmatine and N-methyl-l-arginine reveal that modification at the guanidinium group significantly diminishes the propensity for linear assembly of the nanoparticles.

Tristearin bilayers: structure of the aqueous interface and stability in the presence of surfactants

We report results of atomistic molecular dynamics simulations of an industrially-relevant, exemplar triacylglycerol (TAG), namely tristearin (TS), under aqueous conditions, at different temperatures and in the presence of an anionic surfactant, sodium dodecylbenzene sulphonate (SDBS). We predict the TS bilayers to be stable and in a gel phase at temperatures of 350 K and below. At 370 K the lipid bilayer was able to melt, but does not feature a stable liquid-crystalline phase bilayer at this elevated temperature. We also predict the structural characteristics of TS bilayers in the presence of SDBS molecules under aqueous conditions, where surfactant molecules are found to spontaneously insert into the TS bilayers. We model TS bilayers containing different amounts of SDBS, with the presence of SDBS imparting only a moderate effect on the structure of the system. Our study represents the first step in applying atomistic molecular dynamics simulations to the investigation of TAG-aqueous interfaces. Our results suggest that the CHARMM36 force-field appears suitable for the simulation of such systems, although the phase behaviour of the system may be shifted to lower temperatures than is the case for the actual system. Our findings provide a foundation for further simulation studies of the TS-aqueous interface.

Design, synthesis and preliminary analytical evaluation of water soluble reagents for peroxyoxalate chemiluminescence

Describes the investigation into a number of facets of the peroxyoxalate chemiluminescence reaction, and the application of this chemistry to the detection of certain analytes under purely aqueous conditions.

Blue electrogenerated chemiluminescence from water-soluble iridium complexes containing sulfonated phenylpyridine or tetraethylene glycol derivatized triazolylpyridine ligands

Incorporating phenylpyridine- and triazolylpyridine-based ligands decorated with methylsulfonate or tetraethylene glycol (TEG) groups, a series of iridium(III) complexes has been created for green and blue electrogenerated chemiluminescence under analytically useful aqueous conditions, with tri-n-propylamine as a coreactant. The relative electrochemiluminescence (ECL) intensities of the complexes were dependent on the sensitivity of the photodetector over the wavelength range and the pulse time of the applied electrochemical potential. In terms of the integrated area of corrected ECL spectra, with a pulse time of 0.5 s, the intensities of the Ir(III) complexes were between 18 and 102 % that of [Ru(bpy)3 ](2+) (bpy=2,2'-bipyridine). However, when the intensities were measured with a typical bialkali photomultiplier tube, the signal of the most effective blue emitter, [Ir(df-ppy)2 (pt-TEG)](+) (df-ppy=2-(2,4-difluorophenyl)pyridine anion, pt-TEG=1-(2-(2-(2-(2-hydroxyethoxy)ethoxy)ethoxy)ethyl)-4-(2-pyridyl)-1,2,3-triazole), was over 1200 % that of the orange-red emitter [Ru(bpy)3 ](2+) . A combined experimental and theoretical investigation of the electrochemical and spectroscopic properties of the Ir(III) complexes indicated that the greater intensity from [Ir(df-ppy)2 (pt-TEG)](+) relative to those of the other Ir(III) complexes resulted from a combination of many factors, rather than being significantly favored in one area.

Considering the chemical energy requirements of the tri-n-propylamine co-reactant pathways for the judicious design of new electrogenerated chemiluminescence detection systems

The introduction of a 'co-reactant' was a critical step in the evolution of electrogenerated chemiluminescence (ECL) from a laboratory curiosity to a widely utilised detection system. In conjunction with a suitable electrochemiluminophore, the co-reactant enables generation of both the oxidised and reduced precursors to the emitting species at a single electrode potential, under the aqueous conditions required for most analytical applications. The most commonly used co-reactant is tri-n-propylamine (TPrA), which was developed for the classic tris(2,2'-bipyridine)ruthenium(ii) ECL reagent. New electrochemiluminophores such as cyclometalated iridium(iii) complexes are also evaluated with this co-reactant. However, attaining the excited states in these systems can require much greater energy than that of tris(2,2'-bipyridine)ruthenium(ii), which has implications for the co-reactant reaction pathways. In this tutorial review, we describe a simple graphical approach to characterise the energetically feasible ECL pathways with TPrA, as a useful tool for the development of new ECL detection systems.

Facet selectivity in gold binding peptides: exploiting interfacial water structure

Peptide sequences that can discriminate between gold facets under aqueous conditions offer a promising route to control the growth and organisation of biomimetically-synthesised gold nanoparticles. Knowledge of the interplay between sequence, conformations and interfacial properties is essential for predictable manipulation of these biointerfaces, but the structural connections between a given peptide sequence and its binding affinity remain unclear, impeding practical advances in the field. These structural insights, at atomic-scale resolution, are not easily accessed with experimental approaches, but can be delivered via molecular simulation. A current unmet challenge lies in forging links between predicted adsorption free energies derived from enhanced sampling simulations with the conformational ensemble of the peptide and the water structure at the surface. To meet this challenge, here we use an in situ combination of Replica Exchange with Solute Tempering with Metadynamics simulations to predict the adsorption free energy of a gold-binding peptide sequence, AuBP1, at the aqueous Au(111), Au(100)(1 × 1) and Au(100)(5 × 1) interfaces. We find adsorption to the Au(111) surface is stronger than to Au(100), irrespective of the reconstruction status of the latter. Our predicted free energies agree with experiment, and correlate with trends in interfacial water structuring. For gold, surface hydration is predicted as a chief determining factor in peptide-surface recognition. Our findings can be used to suggest how shaped seed-nanocrystals of Au, in partnership with AuBP1, could be used to control AuNP nanoparticle morphology.

Extended studies on fibre diameter measurement with OFDA instrument

OFDA 2000 is a widely used fibre diameter measurement instrument. The instrument can provide improved statistical accuracy measurements in comparison with traditional technology. In this paper, a new technique has been developed to enable fibre diameters to be measured in an aqueous environment using the OFDA 2000 instrument. This new technique was utilised to assess the effects of pH and temperature on the diameters of Merino wool fibres in aqueous environments. Significant changes in fibre diameter under aqueous conditions were found as a function of pH and temperature. It is also demonstrated in this paper that the fibre diameter measurement results can be affected by fibre colour. In both dry and aqueous conditions, variation in fibre diameter was observed on fibres with different colours. This could be due to an optical effect or more likely due to physical changes in the dyed fibres as a result of the presence of dyes. Apart from their physical bulk, dyes may also affect the water content of fibres and hence have an influence on the swelling of fibres when they are measured under ambient regain and wet conditions.

Colour effect on fibre diameter measurement with OFDA 2000

In this study, wool samples from Merino, Corriedale and Lincoln sheep with a wide range of fibre diameters have been dyed and measured for fibre diameter using OFDA 2000 in both dry and conditioned states. Variation in fibre diameter is observed on fibres with different colours in both dry and aqueous conditions. This could be due to an optical effect or more likely due to physical changes in the dyed fibres owing to the presence of dyes. Apart from their physical bulk, dyes may also affect the owing water content of fibres and hence have an influence on the swelling of fibres when they are measured under ambient regain and wet conditions.

Non-covalent adsorption of amino acid analogues on noble-metal nanoparticles: influence of edges and vertices

The operation of many nanostructured biomolecular sensors and catalysts critically hinges on the manipulation of non-covalent adsorption of biomolecules on unfunctionalised noble-metal nanoparticles (NMNPs). Molecular-level structural details of the aqueous biomolecule/NMNP interface are pivotal to the successful realisation of these technologies, but such experimental data are currently scarce and challenging to obtain. Molecular simulations can generate these details, but are limited by the assumption of non-preferential adsorption to NMNP features. Here, via first principles calculations using a vdW-DF functional, and based on nanoscale sized NMNPs, we demonstrate that adsorption preferences to NP features vary with adsorbate chemistry. These results show a clear distinction between hydrocarbons, that prefer adsorption to facets over edges/vertices, over heteroatomic molecules that favour adsorption onto vertices over facets. Our data indicate the inability of widely used force-fields to correctly capture the adsorption of biomolecules onto NMNP surfaces under aqueous conditions. Our findings introduce a rational basis for the development of new force-fields that will reliably capture these phenomena.

Aqueous/micellar peroxyoxalate chemiluminescent detection for ion chromatography

This thesis covers the development of the traditionally fluorescent bis(8-quinolinol-5-sulfonic acid) magnesium (II) fluorophore as a chemiluminescent emitter. A brief description of luminescence spectroscopy and its application to analytical chemistry lays the foundation to the discussion of the results obtained herein. This includes the synthesis and identification of two so called ‘water soluble’ aryl oxamides 2,2’-oxalyl-bis(trifluoromethanesulfonyl) imino] ethylene-bis(N- methylpyridinium) trifluoromethane sulfonate (PETQ) and 2,2’-oxalyl-bis(trifluoromethanesulfonyl) imino]ethylene-bis(N-pyridinium) chloride (PETH), previously developed for the US navy as a possible emergency light source, yet the synthetic methodology were incomplete. The inconsistencies of the synthetic methods for PETQ and PETH were overcome with yields satisfactory for their preliminary analytical evaluation. The evaluation of these aryl oxamides, including 4,4’-oxalyI- bis[(trifluoromethanesulfonyl) imino]ethylene-bis(l-methyM-benzylpiperidinium) trifluoromethanesulfonate (BPTQ), 4,4’-oxalyl-bis [(trifluoromethylsulfonyl)imino] ethylene-bis(N-methylmorpholinium)trifluoromethanesulfonate (METQ) and the oxalate bis(2,4,6-trichlorophenyl) oxalate (TCPO) were performed with the peroxyoxalate chemiluminescent reaction using bis(8-quinolinol-5-sulfonic acid) magnesium (II) as the fluorophore. A univariate optimisation of this system resulted in 0,0082 mol 1-1 the detection limit of magnesium in the absence of cationic surfactants and 0.0041 mol 1-1 in their presence for the majority of these compounds. The oxamides were found to be insoluble in water with long ulrasonication periods required to dissolve the compound, with solvents such as acetonitrile preferred. The determination of other chemiluminescent metal-8HQS chelates to replace magnesium -8HQS in the peroxyoxalate were limited to Al (III), Cd (II), Ca (II), In (II) and Zn (II), unfortunately these metals all possessed poorer detection limits than those obtained using magnesium The base reaction conditions used for the flow injection system with chemiluminescent detection were transferred to an ion chromatographic configuration for the separation of magnesium from other cations on an exchange column. After a univariate and simplex optimisation of these conditions, the detection limit of magnesium was found to be 0.0411 mol 1-1 which was less than the limits that could be achieved with fluorescent detection, The further development of this reaction to incorporate the displacement of magnesium from Mg-EDTA by other metals that possessed a higher conditional stability constant than magnesium also proved to be problematic with interferences from not only EDTA but from the eluant (lactic acid) from the cation column. Using this system the detection limits of the displacing metals were found to be in the order of 10 mg 1-1 which was substantially less that what was observed when exactly the same configuration was used with fluorescent detection. The final component of the thesis entails the discussion of the background emission that results from the reaction of oxamides/oxalates with hydrogen peroxide. A detailed investigation into the reaction of TCPO and hydrogen peroxide in the presence of various additives, such as imidazole , heavy atoms and triethylamine illustrated the existence of a further intermediate in fee mechanism for this reaction. The species responsible for this emission was attributed to the degradation product 2,4,6-trichlorophenyi of TCPO, which was supported by the non-existent background present with the oxamides that do not contain this degradation product.

A novel cloud-point extraction process for preconcentrating selected polycyclic aromatic hydrocarbons in aqueous solution

A novel but simple cloud-point extraction (CPE) process is developed to preconcentrate the trace of selected polycyclic aromatic hydrocarbons (PAHs) with the use of the readily biodegradable nonionic surfactant Tergitol 15-S-7 as extractant. The concentrations of PAHs, mixtures of naphthalene and phenanthrene as well as pyrene, in the spiked samples were determined with the new CPE process at ambient temperature (23 °C) followed by high performance liquid chromatography (HPLC) with fluorescence detection. More than 80% of phenanthrene and pyrene, respectively, and 96% of naphthalene initially present in the aqueous solutions with concentrations near or below their aqueous solubilities were recovered using this new CPE process. Importantly Tergitol 15-S-7 does not give any fluorometric signal to interfere with fluorescence detection of PAHs in the UV range. No special washing step is, thus, required to remove surfactant before HPLC analyses. Different experimental conditions were studied. The optimum conditions for the preconcentration and determi nation of these selected PAHs at ambient temperature have been established as the following:  (1) 3 wt % surfactant; (2) addition of 0.5 M Na2SO4; (3) 10 min for equilibration time; and (4) 3000 rpm for centrifugal speed with duration of 10 min.

Stability of aqueous films between bubbles. Part 2. Effects of trace impurities and evaporation

The stability of water films has been investigated with a Mysels-Scheludko type film balance. Minor trace impurities in water do not affect the lifetime of water films under vapor saturation, but significantly influence the stability in free evaporation. Trace amounts of positively adsorbed contaminants induce Marangoni-driven flow that destabilizes films under evaporation conditions whereas negatively adsorbed electrolytes actually prolong stability by reversing interfacial tension gradients and driving a steady circulation within the film. At high thinning rates, pure-water films develop exotic-appearing flow patterns and break due to a strong coupling between hydrodynamic and interfacial tensiongradient adsorption stresses. The most dominant factor of transient film stabilization in dynamic conditions under evaporation is a surface tension gradient created in the film. We discuss surface tension gradients in transient films created by temperature differences, impurity concentration, and expansion of the films.