Frictional behaviour and wear performance of a nitrocarburised coating sliding against AISI 1019 steel

This work employed a commercial nitrocaburising process to diffuse a coating onto M2 grade high speed tool steel. Properties of the nitrocaburised coating (CN) such as thickness, roughness and hardness were characterised using a variety of techniques including Glow-Discharge Optical Emission Spectrometry (GD-OES) and Scanning Electron Microscopy (SEM). A tribological test has been developed in which two nominally identical crossed cylinders slide over each other under selected test conditions. The test has been employed to investigate the wear performance of both CN coated and uncoated M2 specimens and frictional behaviour of the sliding interface between the tool and a AISI 1019 steel workpiece under unlubricated (dry) and lubricated conditions. Fourier Transform Infrared Spectroscopy (FTIR) was used to monitor the formation of chemical species from the oxidation of lubricant during tribological testing.

Fluidized bed CrN coating formation on prenitrocarburized plain carbon steel

CrN coatings were formed on plain carbon steel by prenitrocarburizing, followed by thermoreactive deposition and diffusion (TRD) in a fluidized bed furnace at 570 °C. During TRD, Cr was transferred from Cr powder in the fluidized bed to the nitrocarburized substrates by gas-phase reactions initiated by reaction of HCl gas with the Cr. The microstructural processes occurring in the white layer, caused by N diffusion toward the surface during this stage were studied. This study compares TRD atmospheres employing inert gas and HCl or inert gas, H2, and HCl. Surface characterization was performed by scanning electron microscopy (SEM), x-ray diffraction (XRD), and glow-discharge optical-emission spectroscopy (GDOES).

Cr(N,C) diffusion coating formation on pre-nitrocarburised H13 tool steel

The microstructural processes of Cr(N,C) coating formation by thermoreactive deposition and diffusion (TRD) on pre-nitrocarburised H13 tool steel were studied. Both nitrocarburising and TRD were performed in fluidized bed furnaces at 570 °C. During TRD, chromium was transferred from chromium powder in the fluidized bed, to the nitrocarburised substrates by gas-phase reactions initiated by reaction of HCl gas with the chromium. Addition of 30% H2 to the input inert gas was found to increase the rate of coating formation, although hydrogen reduction resulted in rapid loss of nitrogen to the surface. The reason for the increased rate of coating formation could not be established without further investigation, although several possible explanations have been proposed. It was found that porosity and the formation of an iron nitride ‘cover layer’ during nitrocarburising were the biggest influences on the microstructure of the Cr(N,C) coating. Microstructural characterization of the coatings was performed by scanning electron microscopy (SEM), X-ray diffraction (XRD) and glow discharge optical emission spectroscopy (GDOES).

Interaction between the coating characteristics of galvanneal steel and forming parameters during flat die drawing

Galvanneal steel is considered to be better for automotive applications than its counterpart, galvanized steel, mainly because of its superior coating and surface properties. Galvanneal steel is produced by hot dipping sheet steel in a bath of molten zinc with small, controlled, levels of aluminium, followed by annealing which creates a Fe-Zn intermetallic layer. This intermetallic layer of the coating improves spot weldability and improves subsequent paint appearance. However, if the microstructure of the coating is not properly controlled and forming parameters are not properly selected, wear of the coating could occur during stamping. Frictional sliding of the sheet between the tool surfaces results in considerable amount of coating loss. An Interstitial Free steel with a Galvanneal coating of nominally 60g/m2 was used for the laboratory experiments. Flat Face Friction (FFF) tests were performed with different forming conditions and lubricants to simulate the frictional sliding in stamping. Glow-Discharge Optical Emission Spectrometry (DG-OES) was used to measure the change in the coating thickness during sliding. Optical microscopy was considered for imaging the surfaces as well as an optical method to compare the changes in the coating thickness during the forming. The change to the Galvanneal coating thickness was found to be a function of forming parameters.

Synthesis, polymerization and wool coating studies of 3-iso-butylpyrrole and 3-iso-pentylpyrrole

In a four-step method starting from pyrrole, the synthesis of 3-iso-butylpyrrole and 3-iso-pentylpyrrole, was achieved in 45 and 44% yields, respectively. Polymerization studies of these branched alkyl pyrroles are described and the results compared with those obtained for the unbranched structural isomers n-butyl and n-pentylpyrrole. A series of conductive textiles were produced by the chemical polymerization of the iso-alkylpyrroles using both solution and vapour polymerization techniques. Fabrics coated with poly-iso-alkylpyrrole formed using the solution polymerization method had a lower surface resistance than those formed using the vapour polymerization method. These conductivity results were in direct contrast to those previously obtained for 3-n-alkylpyrroles on fabrics. A remarkable crystal-like growth on the surface of the textile fabric was observed when solution polymerization of 3-iso-pentylpyrrole was employed—reinforcing the notion that subtle changes in monomer structure can drastically affect bulk polymer properties.

Polymerising pyrrole on polyester textiles and controlling the conductivity through coating thickness

The surface resistance of polypyrrole (PPy)-coated polyester fabrics was investigated and related to coating thickness, which was controlled by adjusting the reactant concentrations. The thickness of the coating initially increased rapidly followed by a steady increase when the concentration of pyrrole (Py) was larger than a concentration of approximately 0.4 mg/ml. The surface resistance decreased from 10⁶ to 10³ Ω with increase in pyrrole concentration within 0.2 mg/ml until the concentration reached a value of about 0.4 mg/ml, above which the rate of decrease diminished. The effect of initial treatment with monomer or oxidant prior to polymerisation reaction with regards to thickness and surface resistance was minimal. The immersion time of the textile into the monomer solution prior to polymerisation reaction did not have a significant effect on the abrasion resistance.

Improvement of adhesion of conductive polypyrrole coating on wool and polyester fabrics using atmospheric plasma treatment

In this paper wool and polyester fabrics were pretreated with atmospheric plasma glow discharge (APGD) to improve the ability of the substrate to bond with anthraquinone-2-sulfonic acid doped conducting polypyrrole coating. A range of APGD gas mixtures and treatment times were investigated. APGD treated fabrics were tested for surface contact angle, wettability and surface energy change. Effect of the plasma treatment on the binding strength was analyzed by studying abrasion resistance, surface resistivity and reflectance. Investigations showed that treated fabrics exhibited better hydrophilicity and increased surface energy. Surface treatment by an APGD gas mixture of 95% helium/5% nitrogen yielded the best results with respect to coating uniformity, abrasion resistance and conductivity.

Photochromic wool fabrics from a hybrid silica coating

In this work, a photochromic wool fabric has been prepared by applying a photochromic-dye hybrid silica sol-gel onto the surface of fabric. The photochromic fabric was found to have a very quick optical response. Two types of silica were used as the matrix material, and the type of silica had a small effect only on the photochromic performance, the fabric washing fastness, and water contact angle, but affected the fabric handle property considerably. The silica from a precursor containing a long alkyl chain showed very little influence on the fabric handle and better photochromic performance than that containing a phenyl group.

One-step coating of fluoro-containing silica nanoparticles for universal generation of surface superhydrophobicity

Stable superhydrophobic surfaces with water contact angles over 170 degrees and sliding angles below 7 degrees were produced by simply coating a particulate silica sol solution of co-hydrolysed TEOS/fluorinated alkyl silane with NH₃^.H₂O on various substrates, including textile fabrics (e.g. polyester, wool and cotton), electrospun nanofibre mats, filter papers, glass slides, and silicon wafers.

Fast response photochromic textiles from hybrid silica surface coating

In this study, a hybrid silica sol-gel embedded with a photochromic dye has been applied to wool fabric to form a photochromic coating. The treated wool fabrics showed very quick photochromic response. Five different silanes have been used as the silica precursor, and the resultant coating showed slight differences in photochromic performance, fabric washing fastness, and surface hydrophilicity. However, the silica type had a considerable influence on fabric handle property. The silica matrix from the silane containing a long alkyl chain had a very little influence on the fabric handle and better photochromic performance than those from other different silane precursors.

Residual thermal stresses in a Fe3Al/Al2O3 gradient coating system

To combine the merits of both metals and ceramics into one material, many researchers have been studying the deposition of alumina coating using plasma spray on metal substrates. However, as the coatings are deposited at a high temperature, residual thermal stresses develop due to the mismatch of thermal expansion coefficients of the coating and substrate and these are responsible for the initiation and expansion of cracks, which induce the possible failure of the entire material. In this paper, the residual thermal-structural analysis of a Fe3Al/Al2O3 gradient coating on carbon steel substrate is performed using finite element modelling to simulate the plasma spray. The residual thermal stress fields are obtained and analyzed on the basis of temperature fields in gradient coatings during fabrication. The distribution of residual thermal stresses including radial, axial and shear stresses shows stress concentration at the interface between the coatings and substrate. The mismatch between steel substrate and composite coating is still the dominant factor for the residual stresses