Direct current electric potential in an anisotropic half-space with vertical contact containing a conductive 3D body

Detailed studies of anomalous conductors in otherwise homogeneous media have been modelled. Vertical contacts form common geometries in galvanic studies when describing geological formations with different electrical conductivities on either side. However, previous studies of vertical discontinuities have been mainly concerned with isotropic environments. In this paper, we deal with the effect on the electric potentials, such as mise-`a-la-masse anomalies, due to a conductor near a vertical contact between two anisotropic regions. We also demonstrate the interactive effects when the conductive body is placed across the vertical contact. This problem is normally very difficult to solve by the traditional numerical methods. The integral equations for the electric potential in anisotropic half-spaces are established. Green’s function is obtained using the reflection and transmission image method in which five images are needed to fit the boundary conditions on the vertical interface and the air-earth surface. The effects of the anisotropy of the environments and the conductive body on the electric potential are illustrated with the aid of several numerical examples.

Anisotropic wetting characteristics on submicrometer-scale periodic grooved surface

Submicrometer-scale periodic structures consisting of parallel grooves were prepared on azobenzene-containing multiarm star polymer films by laser interference. The wetting characteristics on the patterned surfaces were studied by contact angle measurements. Macroscopic distortion of water drops was found on such small-scale surface structures, and the contact angles measured from the direction parallel to the grooves were larger than those measured from the perpendicular direction. A thermodynamic model was developed to calculate the change in the surface free energy as a function of the instantaneous contact angle when the three-phase contact line (TPCL) moves along the two orthogonal directions. It was found that the fluctuations, i.e., energy barriers, on the energy versus contact angle curves are crucial to the analysis of wetting anisotropy and contact angle hysteresis. The calculated advancing and receding contact angles from the energy versus contact angle curves were in good agreement with those measured experimentally. Furthermore, with the groove depth increasing, both the degree of wetting anisotropy and the contact angle hysteresis perpendicular to the grooves increased as a result of the increase in the energy barrier. The theoretical critical value of the groove depth, above which the anisotropic wetting appears, was determined to be 16 nm for the grooved surface with a wavelength of 396 nm. On the other hand, the effect of the groove wavelength on the contact angle hysteresis perpendicular to the grooves was also interpreted on the basis of the thermodynamic model. That is, with the wavelength decreasing, the contact angle hysteresis increased due to the increase in the number of energy barriers. These results may provide theoretical evidence for the design and application of anisotropic wetting surface.

Anisotropic mechanical properties of nickel foams fabricated by powder metallurgy

In the present study, porous nickel foam samples with pore sizes of 20 μm and 150 μm and porosities of 60 % and 70 % were fabricated by the space-holding sintering method via powder metallurgy. Electron scanning microscopy (SEM) and Image-Pro Plus were used to characterise the morphological features of the porous nickel foam samples. The anisotropic mechanical properties of porous nickel foams were investigated by compressive testing loading in different directions, i.e. the major pore axis and minor pore axis. Results indicated that the nominal stress of the nickel foam samples increases with the decreasing of the porosity. Moreover, the foam sample exhibited significantly higher nominal stress for loading in the direction of the major pore axis than loading in direction of the minor pore axis. It is also noticeable that the nominal stress of the nickel foams increases with the decreasing of the pore size. It seems that the deformation behaviour of the foams with a pore size in the micron-order differs from those with a macro-porous structure.

Ion exchange, anisotropic structure and thermal stability of polypyrrole films

The thermal stability of electrochemically prepared polypyrrole (PPy) films with p-toluene sulfonate (pTS) or perchlorate (CIOP₄⁻) counter ion (PPy/pTS and PPy/ClO₄⁻) is improved by simple treatment with aqueous sulfuric acid, sodium sulfate or sodium bisulfate. The degree of stabilization achieved depends on the solution, temperature and duration of treatment. PPy/pTS is easily stabilized and thick films (43μm) retain 90 % of the initial conductivity after long period (300 h) at 150 °C, while thinner films (12 μm) retain slightly less (70 %). A model for the conductivity decay has been proposed. Although the mechanism for improved stability is not yet clear it is apparent that the level of ion exchange and the original polymer microstructure are important. The early stages of ion exchange are not symmetrical and diffusion is facilitated at the electrode side of the film. Furthermore, X-ray diffraction shows no evidence of morphological change after treatment of thick PPy/pTS but in thin PPy/pTS and PPy/ClO₄⁻ films an additional peak is indicative of more ordered structure following treatment. These observation may imply that there is a higher density of crosslinks and branching at the growth side than at the electrode side of the film.

Coloration of cotton fibers with anisotropic silver nanoparticles

Anisotropic silver nanoparticles were assembled on cotton fibers to realize the coloration of cotton. The assembly of silver nanoparticles on fibers was achieved by linking of poly(diallyldimethylammonium chloride) (PDDA) at room temperature. The silver nanoparticle treated cotton showed different colors because of localized surface plasmon resonance (LSPR) property of silver nanoparticles. The coloration was completed through electrostatic interaction between the PDDA treated cotton surface and the anisotropic silver nanoparticles in the reaction system. Scanning electron microscopy (SEM) characterization demonstrated that the morphologies of silver nanoparticles remained unchanged during the coloration process, so the treated cotton inherited the LSPR optical features of silver nanoparticles. Moreover, the cotton colorated with silver nanoparticles showed reasonably good color fastness to washing, which will facilitate the practical application of this coloration process.

Automatic cast listing in feature-length films with Anisotropic Manifold Space

Our goal is to automatically determine the cast of a feature-length film. This is challenging because the cast size is not known, with appearance changes of faces caused by extrinsic imaging factors (illumination, pose, expression) often greater than due to differing identities. The main contribution of this paper is an algorithm for clustering over face appearance manifolds. Specifically: (i) we develop a novel algorithm for exploiting coherence of dissimilarities between manifolds, (ii) we show how to estimate the optimal dataset-specific discriminant manifold starting from a generic one, and (iii) we describe a fully automatic, practical system based on the proposed algorithm. The performance of the system is evaluated on well-known featurelength films and situation comedies on which it is shown to produce good results.