Hydraulic performance of geosynthetic clay liners to sulfuric acid solutions

The ability of geosynthetic clay liners (GCLs) to contain acidic mining leachates is examined. The results of saturated hydraulic conductivity (k) of two GCLs permeated with sulfuric acid solutions (H2SO4) at 0.015M, 0.125M and 0.5M concentrations are reported. Also, the saturated k values of consolidated (35kPa) bentonite cakes made from sodium bentonite extracted from both GCLs were compared to a commonly used magnesium-sodium form bentonite. Chemical compatibility and effects of pre-hydration and effective stress were assessed as part of this study. Results indicated that an increased acid concentration (ionic strength) increased the k of all tested specimens. The ratio of the k0.5 values for non-prehydrated specimens permeated with 0.5M H2SO4 to the kw values for specimens permeated with deionized (DI) water (k0.5/kw) ranged from 10 to 110. Pre-hydration (50-140% water content) and increased effective stress (35-200kPa) improved the performance of GCLs (lower k). Strong correlations were observed between k and liquid limit and swell index parameters independent of pre-hydration and effective stress in this study. However, care should still be taken when using these correlations to evaluate hydraulic performance because the intrinsic micro-structure properties of bentonite, such as porosity, should also be considered. This work showed that, for example, high SI of bentonite does not translate necessarily to a better hydraulic performance of GCLs.

Corrosion behaviour of direct current and active screen plasma carburised AISI 316 stainless steel in boiling sulphuric acid solutions

Active screen plasma is a recently developed plasma surface alloying technique, which has shown potential for addressing some drawbacks associated with conventional direct current plasma processes. In this study, the corrosion performance of untreated, direct current and active screen plasma carburised AISI 316 was investigated by immersion in a boiling solution of sulphuric acid. The experimental results show that the corrosion behaviour of expanded austenite produced by low temperature plasma carburising is controlled by the type and density of surface defects; the corrosion properties of the active screen plasma carburised material are superior to that produced by direct current plasma because of the significantly reduced edge effect and surface defects; and the bias level used in the active screen carburising treatment has a profound effect on the corrosion performance of the material. Based on the experimental results, the corrosion mechanisms involved are discussed.

Acid induced degradation of the bentonite component used in geosynthetic clay liners

Bentonite is a natural clay mineral widely used in the mining and solid waste containment industry, for example, as a soil mixture for the construction of seepage barriers, or as a component of geosynthetic clay liners (GCLs), to provide low hydraulic conductivity. However, degradation of bentonites generally occurs when permeated with acid solutions, such as encountered in mining applications, which may influence physical properties, and particularly, the hydraulic performance of geosynthetic clay liners.In this paper, properties such as Atterberg limits, free swell index, and fluid loss of three bentonites were measured with different concentrations of sulphuric acid solutions. These properties were found to deteriorate even with low (0.015 M) sulphuric acid solutions; higher concentrations (up to 1 M) resulted in larger degradation. X-ray diffraction and infrared spectroscopy were used to monitor the change of bentonites after interaction with the acid solutions. Acid leachates in general result in the overall degradation of the hydraulic performance of geosynthetic clay liners and potentially, any bentonite-soil mixture.

Acid–organic base swollen polymer membranes

In this work, two different polymer membrane systems based on Nafion and Teflon were investigated as proton conductors for polymer membrane fuel cells. Water-free Nafion117 membranes swollen with different non-aqueous solvents were prepared. The solvents included imidazole, imidazole–imidazolium salt solutions, room temperature molten salts and molten salt–acid solutions. Teflon films were treated with a surfactant, or a Nafion solution, to improve their surface properties, and were subsequently swollen with phosphoric acid. Conductivity measurements were carried out on both the Nafion and Teflon membranes. Conductivities in the range of 10⁻³ S cm⁻¹ at around 100°C were obtained. This is still an order of magnitude lower than the corresponding water swollen Nafion at 80°C.

Fabrication of meso-porous sintered metal thin films by selective etching of silica based sacrificial template

 Meso-porous metal materials have enhanced surface energies offering unique surface properties with potential applications in chemical catalysis, molecular sensing and selective separation. In this paper, commercial 20 nm diameter metal nano-particles, including silver and copper were blended with 7 nm silica nano-particles by shear mixing. The resulted powders were cold-sintered to form dense, hybrid thin films. The sacrificial silica template was then removed by selective etching in 12 wt% hydrofluoric acid solutions for 15 min to reveal a purely metallic meso-porous thin film material. The impact of the initial silica nano-particle diameter (7–20 nm) as well as the sintering pressure (5–20 ton·m−2) and etching conditions on the morphology and properties of the final nano-porous thin films were investigated by porometry, pyknometery, gas and liquid permeation and electron microscopy. Furthermore, the morphology of the pores and particle aggregation during shear mixing were assessed through cross-sectioning by focus ion beam milling. It is demonstrated that meso-pores ranging between 50 and 320 nm in average diameter and porosities up to 47% can be successfully formed for the range of materials tested.

Fluid loss as a quick method to evaluate the hydraulic conductivity of geosynthetic clay liners under acidic conditions

This study investigates the performance of bentonite components of geosynthetic clay liners (GCLs) when exposed to aggressive leachates using the fluid loss test and provides a possible quick method for estimating the effect of acidic conditions on hydraulic conductivity. Fluid loss generally increases with increasing acid concentrations. Hydraulic conductivity values back-calculated from the fluid loss tests (kFL) are compared with the values measured using a flexible-wall permeameter (kTri).Generally, the predicted hydraulic conductivity values are conservative (kFL/kTri > 1) under water and low acid concentrations(≤0.015 mol/L). However, the back-calculated hydraulic conductivity is shown to be nonconservative (kFL/kTri < 1) at high acid concentrations (≥0.125 mol/L).

The boundary lubrication of chemically grafted and cross-linked hyaluronic acid in phosphate buffered saline and lipid solutions measured by the surface forces apparatus

High molecular weight hyaluronic acid (HA) is present in articular joints and synovial fluid at high concentrations; yet despite numerous studies, the role of HA in joint lubrication is still not clear. Free HA in solution does not appear to be a good lubricant, being negatively charged and therefore repelled from most biological, including cartilage, surfaces. Recent enzymatic experiments suggested that mechanically or physically (rather than chemically) trapped HA could function as an “adaptive” or “emergency” boundary lubricant to eliminate wear damage in shearing cartilage surfaces. In this work, HA was chemically grafted to a layer of self-assembled amino-propyl-triethoxy-silane (APTES) on mica and then cross-linked. The boundary lubrication behavior of APTES and of chemically grafted and cross-linked HA in both electrolyte and lipid 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) solutions was tested with a surface forces apparatus (SFA). Despite the high coefficient of friction (COF) of μ ≈ 0.50, the chemically grafted HA gel significantly improved the lubrication behavior of HA, particularly the wear resistance, in comparison to free HA. Adding more DOPC lipid to the solution did not improve the lubrication of the chemically grafted and cross-linked HA layer. Damage of the underlying mica surface became visible at higher loads (pressure >2 MPa) after prolonged sliding times. It has generally been assumed that damage caused by or during sliding, also known as “abrasive friction”, which is the main biomedical/clinical/morphological manifestation of arthritis, is due to a high friction force and, therefore, a large COF, and that to prevent surface damage or wear (abrasion) one should therefore aim to reduce the COF, which has been the traditional focus of basic research in biolubrication, particularly in cartilage and joint lubrication. Here we combine our results with previous ones on grafted and cross-linked HA on lipid bilayers, and lubricin-mediated lubrication, and conclude that for cartilage surfaces, a high COF can be associated with good wear protection, while a low COF can have poor wear resistance. Both of these properties depend on how the lubricating molecules are attached to and organized at the surfaces, as well as the structure and mechanical, viscoelastic, elastic, and physical properties of the surfaces, but the two phenomena are not directly or simply related. We also conclude that to provide both the low COF and good wear protection of joints under physiological conditions, some or all of the four major components of joints—HA, lubricin, lipids, and the cartilage fibrils—must act synergistically in ways (physisorbed, chemisorbed, grafted and/or cross-linked) that are still to be determined.

Chemically induced phosphorescence from manganese(II) during the oxidation of various compounds by manganese(III), (IV) break and (VII) in acidic aqueous solutions

Chemiluminescence was observed during the manganese(III), (IV) and (VII) oxidations of sodium tetrahydroborate, sodium dithionite, sodium sulfite and hydrazine sulfate in acidic aqueous solution. From the corrected chemiluminescence spectra, the wavelengths of maximum emission were 689±5 and 734±5 nm when the reactions were performed in sodium hexametaphosphate and sodium dihydrogenorthophosphate/ orthophosphoric acid environments, respectively. The corrected phosphorescence spectrum of manganese(II) sulfate in a solution of sodium hexametaphosphate at 77 K exhibited two peaks with maxima at 688 and 730 nm. The chemical and spectroscopic evidence presented strongly supported the postulation that the emission was an example of solution-phase chemically induced phosphorescence of manganese(II) thereby, confirming earlier predictions that the chemiluminescence from acidic potassium permanganate reactions originated from an excited manganese(II) species.

'Green' treatment of acid mine drainage - a step towards sustainability

Sustainability is becoming increasingly important in the mining and mineral processing industries and must incorporate the associated waste products. Acid mine drainage (AMD) is one such by-product and is one of the most serious environmental problems facing the minerals industry today. The oxidation of sulphidic mine wastes often continues for a substantial period of time after mine closure, resulting in difficult and costly remediation and rehabilitation works. Mining companies are often reluctant to spend increasing amounts of money on waste treatment when the mine life is limited or even finished. Hence a simple, low maintenance and low-cost method of treating AMD is required. Whilst this paper does not address the issue of AMD, it does propose methods for removal of individual species from AMD with potential benefits, including raising AMD pH.

A novel concept of using biosolids as a biological adsorbent, or ‘biosorbent’, of metals from AMD is being investigated at a laboratory/pilot scale level. Biosolids are a by-product resulting from the biological treatment of wastewater, and have been previously shown to adsorb metals from aqueous solutions. This could lead to an environmentally sustainable or ‘green’ method for treating both AMD discharges and disposing/reusing the biosolids.

The result of a laboratory-scale study of the biosorption of Zn(II) is presented in this paper. Physical parameters including reaction kinetics, mixing speed and solution pH were investigated. Solution pH also rose an average of 2 pH units over the 24 hour equilibrium time – a valuable side effect when treating acid mine drainage. The outcome of the study highlights the usefulness of biosolids as a biosorbent for the removal/recovery of metal ions from acid mine drainage. A simple, low-cost treatment technology requiring low maintenance would be beneficial to the mining industry to address some issues relating to AMD and would help integrate environmental and economic considerations into sustainable environmental management.

A study of acid/base treatments of polypyrrole films using 13C n.m.r. spectroscopy

Electrodeposited polypyrrole films prepared with paratoluenesulfonate (pTS), dodecylsulfate (DDS) and perchlorate anions were treated with acidic and basic solutions, and their structure was investigated by 13C solid state n.m.r. spectroscopy. This technique has confirmed that pTS is completely removed from the film in both acidic and basic solutions whilst DDS is only partially removed and tends to decompose upon treatment with H2SO4. The appearance of shoulders at 143 ppm upon treatment with 0.5 M base indicates formation of a quinoid pyrrole structure. Substitution on the β-carbon by OH cannot be confirmed from the present spectra. Stronger base causes a more dramatic change in the polypyrrole backbone with an obvious increase in the electron density on the β-carbons, consistent with the reduction of the carbon backbone. There is no indication of quinoid units in this case. Acid treatments result in considerable broadening of the main 127 ppm polypyrrole peak.

Substituted naphthoquinones as novel amino acid sensitive reagents for the detection of latent fingermarks on paper surfaces

In this paper, we present our preliminary studies into naphthoquinones as novel reagents for the detection of latent fingermarks on paper. Latent fingermarks deposited on paper substrates were treated with solutions of selected naphthoquinones in ethyl acetate/HFE-7100, with subsequent heating. The selected compounds were 1,4-dihydroxy-2-naphthoic acid, 1,2-naphthoquinone-4-sulfonate, 2-methoxy-1,4-naphthoquinone and 2-methyl-1,4-naphthoquinone. All of the tested compounds yielded purple-brown visible fingermarks, which also exhibited photoluminescence when illuminated with a high intensity filtered light source at 555nm and viewed through red goggles. Indirect heat using an oven at 150 ◦C for 1 h was found to be superior to direct heat with an iron, which while providing faster development lead to increased levels of background colouration. Luminescence spectrophotometry revealed differences in photoluminescence characteristics for fingermarks developed with the different naphthoquinones, with excitation over the range 530–590 nm. Luminescence spectrophotometry of developed lysine, glycine and serine spots on paper was used to confirm that the naphthoquinones were reacting with amino acids in the latent fingermark.

Structure and properties of biomedical films prepared from aqueous and acidic silk fibroin solutions

Silk fibroin films are promising materials for a range of biomedical applications. To understand the effects of casting solvents on film properties, we used water (W), formic acid (FA), and trifluoroacetic acid (TFA) as solvents. We characterized molecular weight, secondary structure, mechanical properties, and degradation behavior of cast films. Significant degradation of fibroin was observed for TFA-based film compared to W and TA-based films when analyzed by SDS-PAGE. Fibroin degradation resulted in a significant reduction in tensile strength and modulus of TFA-based films. Compared to water, TFA-based films demonstrated lower water solubility (19.6% vs. 62.5% in 12 h) despite having only a marginal increase in their ß-sheet content (26.9% vs. 23.7%). On the other hand, FA-based films with 34.3% ß-sheet were virtually water insoluble. Following solubility treatment, ß-sheet content in FA-based films increased to 50.9%. On exposure to protease XIV, water-annealed FA-based films lost 74% mass in 22 days compared to only 30% mass loss by ethanol annealed FA films. This study demonstrated that a small variation in the ß-sheet percentage and random coil conformations resulted in a significant change in the rates of enzymatic degradation without alteration to their tensile properties. The film surface roughness changed with the extent of enzymatic hydrolysis.

Extraction of copper(II) ions from aqueous solutions with a methimazole-based ionic liquid

The recently synthesized ionic liquid (IL) 2-butylthiolonium bis(trifluoromethanesulfonyl)amide, [mimSBu][NTf2], has been used for the extraction of copper(II) from aqueous solution. The pH of the aqueous phase decreases upon addition of [mimSBu]+, which is attributed to partial release of the hydrogen attached to the N(3) nitrogen atom of the imidazolium ring. The presence of sparingly soluble water in [mimSBu][NTf2] also is required in solvent extraction studies to promote the incorporation of Cu(II) into the [mimSBu][NTf2] ionic liquid phase. The labile copper(II) system formed by interacting with both the water and the IL cation component has been characterized by cyclic voltammetry as well as UV−vis, Raman, and 1H, 13C, and 15N NMR spectroscopies. The extraction process does not require the addition of a complexing agent or pH control of the aqueous phase. [mimSBu][NTf2] can be recovered from the labile copper−water−IL interacting system by washing with a strong acid. High selectivity of copper(II) extraction is achieved relative to that of other divalent cobalt(II), iron(II), and nickel(II) transition-metal cations. The course of microextraction of Cu2+ from aqueous media into the [mimSBu][NTf2] IL phase was monitored in situ by cyclic voltammetry using a well-defined process in which specific interaction with copper is believed to switch from the ionic liquid cation component, [mimSBu], to the [NTf2] anion during the course of electrochemical reduction from Cu(II) to Cu(I). The microextraction−voltammetry technique provides a fast and convenient method to determine whether an IL is able to extract electroactive metal ions from an aqueous solution.

Crosslinking neat ultrathin films and nanofibres of pH-responsive poly(acrylic acid) by UV radiation

Electrospun polyelectrolyte hydrogel nanofibres are being developed for many applications including artificial muscles, scaffolds for tissue engineering, wound dressings and controlled drug release. For electrospun polyelectrolytes, a post-spinning crosslinking process is necessary for producing a hydrogel. Typically, radiation or thermal crosslinking routines are employed that require multifunctional crosslinking molecules and crosslink reaction initiators (free radical producers). Here, ultraviolet subtype-C (UVC) radiation was employed to crosslink neat poly(acrylic acid) (PAA) nanofibres and films to different crosslink densities. Specific crosslink initiators or crosslinking molecules are not necessary in this fast and simple process providing an advantage for biological applications. Scanning probe microscopy was used for the first time to measure the dry and wet dimensions of hydrogel nanofibres. The diameters of the swollen fibres decrease monotonically with increasing UVC radiation time. The fibres could be reversibly swollen/contracted by treatment with solutions of varying pH, demonstrating their potential as artificial muscles. The surprising success of UVC radiation exposure to achieve chemical crosslinks without a specific initiator molecule exploits the ultrathin dimensions of the PAA samples and will not work with relatively thick samples.