Tribology of lubricated nitrocarburised and titanium carbonitride surfaces

In the current work, two different coatings, nitrocarburised (CN) and titanium carbonitride (TiCN) on M2 grade high speed tool steel, were prepared by commercial diffusion and physical vapour deposition (PVD) techniques, respectively. Properties of the coating were characterised using a variety of techniques such as Glow-Discharge Optical Emission Spectrometry (GD-OES) and Scanning Electron Microscopy (SEM). Three non-commercial, oil-based lubricants with simplified formulations were used for this study. A tribological test was developed in which two nominally geometrically-identical crossed cylinders slide over each other under selected test conditions. This test was used to evaluate the effectiveness of a pre-applied lubricant film and a surface coating for various conditions of sliding wear. Engineered surface coatings can significantly improve wear resistance of the tool surface but their sliding wear performances strongly depend on the type of coating and lubricant combination used. These coating-lubricant interactions can also have a very strong effect on the useful life of the lubricant in a tribological system. Better performance of lubricants during the sliding wear testing was achieved hen used with the nitrocarburised (CN) coating. To understand the nature of the interactions and their possible effects on the coating-lubricant system, several surface analysis techniques were used. The molecular level investigation of Fourier Transform Infrared Spectroscopy (FTIR) revealed that oxidative degradation occurred in all used oil-based lubricants during the sliding wear test but the degradation behaviour of oil-based lubricants varied with the coating-lubricant system and the wear conditions. The main differences in the carbonyl oxidation region of the FTIR spectra (1900-1600 cm-1) between different coating-lubricant systems may relate to the effective lifetime of the lubricant during the sliding wear test. Secondary Ion Mass Spectrometry (SIMS) depth profiling shows that the CN coating has the highest lubricant absorbability among the tested tool surfaces. Diffusion of chlorine (C1), hydrogen (H) and oxygen (O) into the surface of subsurface of the tool suggested that strong interactions occurred between lubricant and tool surface during the sliding wear test. The possible effects of the interactions on the performance of whole tribological system are also discussed. The study of Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) indicated that the envelope of hydrocarbons (CmHn) of oil lubricant in the positive TOF-SIMS spectra shifted to lower mass fragment after the sliding wear testing due to the breakage of long-chain hydrocarbons to short-chain ones during the degradation of lubricant. The shift of the mass fragment range of the hydrocarbon (CmHn) envelope caries with the type of both tool surface and lubricant, again confirming that variation in the performance of the tool-lubricant system relates to the changes in surface chemistry due to tribochemical interactions at the tool-lubricant interface under sliding wear conditions. The sliding wear conditions resulted in changes not only in topography of the tool surface due to mechanical interactions, as outlined in Chapter 5, but also in surface chemistry due to tribochemical interactions, as discussed in Chapters 6 and 7.

Confocal laser scanning microscopy elucidation of the micromorphology of the leaf cuticle and analysis of its chemical composition

Electron microscopy techniques such as transmission electron microscopy (TEM) and scanning electron microscopy (SEM) have been invaluable tools for the study of the micromorphology of plant cuticles. However, for electron microscopy, the preparation techniques required may invariably introduce artefacts in cuticle preservation. Further, there are a limited number of methods available for quantifying the image data obtained through electron microscopy. Therefore, in this study, optical microscopy techniques were coupled with staining procedures and, along with SEM were used to qualitatively and quantitatively assess the ultrastructure of plant leaf cuticles. Leaf cryosections of Triticum aestivum (wheat), Zea mays (maize), and Lupinus angustifolius (lupin) were stained with either fat-soluble azo stain Sudan IV or fluorescent, diarylmethane Auramine O and were observed under confocal laser scanning microscope (CLSM). For all the plant species tested, the cuticle on the leaf surfaces could be clearly resolved in many cases into cuticular proper (CP), external cuticular layer (ECL), and internal cuticular layer (ICL). Novel image data analysis procedures for quantifying the epicuticular wax micromorphology were developed, and epicuticular waxes of L. angustifolius were described here for the first time. Together, application of a multifaceted approach involving the use of a range of techniques to study the plant cuticle has led to a better understanding of cuticular structure and provides new insights into leaf surface architecture.

Impact of fermented mulberry leaf and fish offal in diet formulation of Indian major carp (Labeo rohita)

Large quantities of fish offal and mulberry leaf are generated globally. The present study aimed to understand their potential utilization in aqua diet formulation, after proper fermentation, as raw materials to replace fish meal in Indian major carp (Labeo rohita) compounded diet. Fish offal meal (FOM) and mulberry leaf meal (MLM) were used in a 2 × 3 factorial design, to evaluate (i) two different fermented mixtures with the inclusion of both FOM and MLM or only MLM and (ii) to replace three different level of dietary fishmeal: 50, 75 or 80 %. An indoor trial, to evaluate diet intake and digestibility and an outdoor trial to evaluate growth performances were impended in Indian major carp fingerlings. The results showed that FOM and MLM are promising raw materials that can be successfully used in the formulation of diet for the Indian major carp. Specifically, the addition of a proper amount of MLM in the fermentation of FOM produced a fermented mixture that could successfully replace up to 80 % of FM in the diet formulation.

The electrochemical surface forces apparatus : the effect of surface roughness, electrostatic surface potentials, and anodic oxide growth on interaction forces, and friction between dissimilar surfaces in aqueous solutions

We present a newly designed electrochemical surface forces apparatus (EC-SFA) that allows control and measurement of surface potentials and interfacial electrochemical reactions with simultaneous measurement of normal interaction forces (with nN resolution), friction forces (with μN resolution), and distances (with Å resolution) between apposing surfaces. We describe three applications of the developed EC-SFA and discuss the wide-range of potential other applications. In particular, we describe measurements of (1) force–distance profiles between smooth and rough gold surfaces and apposing self-assembled monolayer-covered smooth mica surfaces; (2) the effective changing thickness of anodically growing oxide layers with Å-accuracy on rough and smooth surfaces; and (3) friction forces evolving at a metal–ceramic contact, all as a function of the applied electrochemical potential. Interaction forces between atomically smooth surfaces are well-described using DLVO theory and the Hogg–Healy–Fuerstenau approximation for electric double layer interactions between dissimilar surfaces, which unintuitively predicts the possibility of attractive double layer forces between dissimilar surfaces whose surface potentials have similar sign, and repulsive forces between surfaces whose surface potentials have opposite sign. Surface roughness of the gold electrodes leads to an additional exponentially repulsive force in the force–distance profiles that is qualitatively well described by an extended DLVO model that includes repulsive hydration and steric forces. Comparing the measured thickness of the anodic gold oxide layer and the charge consumed for generating this layer allowed the identification of its chemical structure as a hydrated Au(OH)3 phase formed at the gold surface at high positive potentials. The EC-SFA allows, for the first time, one to look at complex long-term transient effects of dynamic processes (e.g., relaxation times), which are also reflected in friction forces while tuning electrochemical surface potentials.

Moisture transfer properties of bifacial fabrics

Many biological plants have bifacial leaves with an adaxial surface and an abaxial surface. These two surfaces can often have different morphologies and properties, and they serve different functions in plant growth. This has inspired us to develop novel bifacial fabrics, with a knitted structure on one face and a woven structure on the other. Bifacial fabrics were produced on a purpose-built machine, using wool, acrylic and polyester yarns, with the woven structure being plain weave, and the knitted structure being single jersey. In this study, the moisture properties of these fabrics were compared with conventional woven and knitted fabrics. The water contact angles of the bifacial fabrics were similar to knitted and woven fabrics, but the absorption time on the woven fabric was much higher than the other fabrics. Liquid moisture transfer properties on both faces of the bifacial fabrics were different, with water spreading and absorption on the woven face being quicker than on the knitted face. These unique properties of bifacial fabrics show that these fabrics could be used as moisture management fabrics, without the need for any additional treatments.

The Permian-Triassic Boundary Stratigraphic Set: characteristics and correlation

Eased on field observations and compilation of data, a new stratigraphic concept, herein named the Permian-Triassic boundary stratigraphic set (PTBST), is proposed. The PTBST consists of, in ascending order, beds of claystone, limestone (or marl) and claystone. This boundary stratigraphic
set has been recognized at many sections in the Yangtze region of South China, with laterally stable lithological characters, the same or comparable biotas, comparable radiometric ages, and identical or similar magnetostratigraphic and chemostratigraphic signals. Therefore, the PTBST marks an isochronous unit and can serve as an important and effective marker set for regional and global correlations.
The important index fossils for the lowermost Triassic, Hindeodus parvus or Claraia, may be diachronous in their first occurrences with respect to the base of the PTBST and, therefore, should not be used as an exclusive indicator for the beginning of the Triassic. Rather more attention should
be paid to events, succession of events and/or event surfaces, which would potentially provide a more precise tool for high-resolution stratigraphic division and correlation.

Extracellular matrix induces formation of organoids and changes in cell surface morphology in cultured human breast carcinoma cells PMC42-LA

In the lactating breast, the development of secretory alveoli consisting of differentiated cells arranged around a central lumen is dependent on signals from the extracellular environment of the cells. There are few cell lines that model this process. We previously showed that the human breast carcinoma line PMC42-LA can be induced to form organoids, reminiscent of secretory alveoli found in the lactating human breast. In this report, we used high-resolution scanning electron microscopy to show that the formation of organoids is accompanied by development of cell surface microvilli. Extracellular matrix-induced formation of microvilli occurred on the internal and external surfaces of cells in the organoids and not on surfaces in contact with the extracellular matrix. Organoid formation of PMC42-LA cells induced a rearrangement of the extracellular matrix, seen in the form of radiating fibers from the organoids. In summary, there is an interaction between PMC42-LA cells and the underlying extracellular matrix, which leads to the formation of polarized cells with well-developed microvilli. This is accompanied by organization of the extracellular matrix. PMC42-LA is a relevant model of the human breast for investigations into cell-cell and cell-matrix interactions.

Effect of surface roughness of Ti, Zr, and TiZr on apatite precipitation from simulated body fluid

Some of the critical properties for a successful orthopedic or dental implant material are its biocompatibility and bioactivity. Pure titanium (Ti) and zirconium (Zr) are widely accepted as biocompatible metals, due to their non-toxicity. While the bioactivity of Ti and some Ti alloys has been extensively investigated, there is still insufficient data for Zr and titanium-zirconium (TiZr) alloys. In the present study, the bioactivity, that is, the apatite forming ability on the alkali and heat treated surfaces of Ti, Zr, and TiZr alloy in simulated body fluid (SBF), was studied. In particular, the effect of the surface roughness characteristics on the bioactivity was evaluated for the first time. The results indicate that the pretreated Ti, Zr and TiZr alloy could form apatite coating on their surfaces. It should be noted that the surface roughness also critically affected the bioactivity of these pretreated metallic samples. A surface morphology with an average roughness of approximately 0.6 microm led to the fastest apatite formation on the metal surfaces. This apatite layer on the metal surface is expected to bond to the surrounding bones directly after implantation.

Computational simulation of gas flow and heat transfer near immersed object in fluidised bed

To improve the understanding of the heat transfer mechanism and find a reliable and simple heat-transfer model, the gas flow and heat transfer between fluidised beds and immersed object surfaces was numerically simulated based on a double particlelayer and porous medium model. The velocity field and temperature distribution of gas were discussed to analyse the heat transfer process.

Source of Bet v 1 loaded inhalable particles from birch revealed

Allergenic proteins present in pollen grains, when inhaled, interact with the airways to cause an attack of asthma in susceptible humans. In one system, grass pollen grains rupture osmotically in rainfall, releasing allergen-containing inhalable particles into the atmosphere. In contrast, birch tree pollen grains do not rupture under these conditions, yet the major allergen, Bet v 1, has been detected in the atmosphere in inhalable particles of unknown origin. It is possible that Bet v 1 may diffuse from intact settled pollen grains and the allergenic material may again become airborne, interacting with settled fine particles from other sources prior to resuspension. This study investigates the mechanism for the release of birch pollen allergen-containing inhalable particles from pollen grains. We propose the hypothesis that (1) airborne birch pollen grains settle on nearby leaf surfaces; (2) then, following light rainfall, the grains germinate and, (3) later, pollen tubes burst, releasing inhalable particles carrying Bet v 1 into the atmospheric aerosol.   We used microscopic analyses of pollen behaviour following anther opening, a Burkard volumetric trap for pollen counts and a high volume air sampler with a two-stage cascade impactor for quantitative immunochemical analyses of Bet v 1. On dry days of high birch pollen count (48 grains/m3, 1.5 ng/m3 of Bet v 1), we found that the surfaces of birch leaves became coated with pollen. This ”pollen rain” is a source of secondary emission of allergens into the atmosphere. We observed that following light rainfall (<1 mm per day), about 80% of the birch pollen grains germinated, producing pollen tubes, especially in the sticky surface secretions of leaf glands. These pollen tubes may grow up to 300 μm in length prior to rupturing, each releasing about 400 starch granules coated with allergen molecules that may, after drying, be dispersed into the aerosol. On these days following light rainfall, the highest atmospheric levels of Bet v 1 (1.18 ng/m3) are associated with inhalable particles. Following heavy rainfall, both pollen and inhalable particles are washed from the atmosphere. Immunoprinting studies show that Bet v 1 is associated with starch granules rather than the smaller orbicules. Bet v 1 is present in the atmosphere in large particles, i.e. in particular pollen grains and in inhalable particles, i.e. in particular starch granules.

An electrochemical impedance study of ionic liquid film formation and aqueous corrosion of magnesium alloy ZE41

Ionic liquid surface treatments are proposed as a method of controlling corrosion processes on magnesium alloys. An important magnesium alloy, ZE41 (nominally 4% Zn and 1% rare earth), was treated with the ionic liquid trihexyl(tetradecyl)phosphonium diphenylphosphate (P₆₆₆₁₄DPP). Impedance spectra were acquired at intervals during the treatment, indicating the development of a film and allowing a measure of the film formation process to be obtained over time. Mechanically polished and electro-polished surfaces were prepared; these surfaces, treated and untreated, were subsequently exposed to 0.1 M NaCl aqueous solutions. The corrosion behavior of the prepared surfaces were assessed using impedance spectroscopy and optical microscopy. The results indicated a significant role for the method of surface preparation used and, in both cases, the ionic liquid treatment produced a more corrosion-resistant surface.

Optimizing oxygen transport through La0.6Sr0.4Co0.2Fe0.8O3-δ hollow fiber by microstructure modification and Ag/Pt catalyst deposition

This work compares the oxygen permeation fluxes of five different La0.6Sr0.4Co0.2Fe0.8O3−δ membranes (e.g. disk, conventional hollow fiber, modified hollow fiber, Ag- or Pt-deposited hollow fiber membranes) to elucidate the dominance of a particular oxygen transport limiting step (e.g., bulk-diffusion or surface reaction) within each of these membranes. At 900 °C and 100 mL min–1 helium gas sweep rate, the oxygen fluxes for disk, conventional hollow fiber, modified hollow fiber, Ag-deposited modified hollow fiber, and Pt-deposited modified hollow fiber membranes are 0.10, 0.33, 0.84, 1.42, and 2.62 mL min–1 cm–2, respectively, denoting enhanced performance in this sequential order. More than 300% enhancement of fluxes is evidenced by modifying the geometry from disk to conventional hollow fiber. This is attributed to the thickness reduction from 1 mm to 0.3 mm, thus implying bulk-diffusion and surface reaction as the jointly limiting transport step for this disk membrane. In contrast to a conventional hollow fiber that has a sandwich cross-sectional structure (e.g. dense center layer sandwiched by two finger-like layers) as well as dense outer and inner circumference surfaces, the modified hollow fiber has only one dense layer in its outer circumference surface with finger-like porous layer extending all the way from outer cross-sectional part to the inner cross-sectional part. This microstructural difference, in turn, provides substantial reduction of membrane thickness and enlarges surface reaction area for modified hollow fiber (relative to conventional hollow fiber), both of which contributes to the reduced bulk-diffusion and surface reaction resistance; evidenced by almost 250% oxygen flux enhancement. To enhance the performance even further, catalyst (e.g., Ag or Pt) deposition on the outer circumference surface of modified hollow fiber can be utilized to reduce its dominating surface reaction resistance. While both catalysts increase the oxygen fluxes, Pt reveals itself as the better candidate relative to Ag due to melting-induced aggregation and growth of Ag at 950 °C.

Hygrothermal effects on painted carbon fibre composite surfaces

In this article, the effect of hygrothermal aging on the painted surface finish of unidirectional and fabric carbon fibre composite laminates, with and without surfacing film was investigated. The results highlighted the importance of ensuring that the composite surface directly beneath the paint layer is made from a uniform material with a consistent thickness in order to minimise surface defects from occurring during aging. The surfacing film was found to minimise the print through development on the painted unidirectional and twill composite surfaces. However, the surfacing film layer was found to intermingle with the carbon fibre plies during cure, which resulted in an uneven film thickness that caused increased levels of orange peel. The twill laminate painted surface produced high levels of print through and surface waviness that was caused by the large resin rich regions located within the tow intersections at the surface which enlarged due to thermal expansion and swelling of the matrix with hygrothermal aging. It was also noted that the small resin rich regions between the individual carbon fibres on the unidirectional composite surface were sufficiently large to print through the painted surface.

A unified mixed-integer programming model for simultaneous fluence weight and aperture optimization in VMAT, tomotherapy, and cyberknife

All rights reserved. In this paper, we propose and study a unified mixed-integer programming model that simultaneously optimizes fluence weights and multi-leaf collimator (MLC) apertures in the treatment planning optimization of VMAT, Tomotherapy, and CyberKnife. The contribution of our model is threefold: (i) Our model optimizes the fluence and MLC apertures simultaneously for a given set of control points. (ii) Our model can incorporate all volume limits or dose upper bounds for organs at risk (OAR) and dose lower bound limits for planning target volumes (PTV) as hard constraints, but it can also relax either of these constraint sets in a Lagrangian fashion and keep the other set as hard constraints. (iii) For faster solutions, we propose several heuristic methods based on the MIP model, as well as a meta-heuristic approach. The meta-heuristic is very efficient in practice, being able to generate dose- and machinery-feasible solutions for problem instances of clinical scale, e.g., obtaining feasible treatment plans to cases with 180 control points, 6750 sample voxels and 18,000 beamlets in 470 seconds, or cases with 72 control points, 8000 sample voxels and 28,800 beamlets in 352 seconds. With discretization and down-sampling of voxels, our method is capable of tackling a treatment field of 8000-64,000cm3, depending on the ratio of critical structure versus unspecified tissues.