A comparative evaluation of the photocatalytic and optical properties of nanoparticulate ZnO synthesised by mechanochemical processing

In this study, mechanochemical processing has been used to manufacture a nanoparticulate powder of ZnO with a controlled particle size and minimal hard agglomeration. The suitability of this ZnO powder for use as either a photocatalyst or an optically transparent UV-filter was evaluated by comparing its optical and photocatalytic properties with those of three commercially available powders that were synthesised by chemical precipitation and flame pyrolysis. The ZnO powder synthesised by mechanochemical processing was found to exhibit high optical transparency and low photocatalytic activity per unit of surface area, which indicates that it is suitable for use in optically transparent UV-filters.

Potential uses of ultrasound in the dairy ultrafiltration processes

There has been a growing interest in the industrial application of ultrasound, especially in the food industry. Power ultrasound can have a number of physical effects; it can increase turbulence through both the introduction of vibrational energy and through acoustic streaming, it can cause both particle agglomeration and particle dispersion and clean surfaces with a scouring action. Our work in this area has focused on the use of ultrasound to enhance membrane processing. Low frequency ultrasound has been used to facilitate cross flow ultrafiltration of dairy whey solutions for both during the ultrafiltration production cycle and the cleaning cycle. During the production cycle, the use of ultrasound reduces both pore blockage and the specific resistance of the fouling cake layer. This leads to higher flux rates and the potential for longer production cycles. During the cleaning cycle, ultrasound systematically increases cleaning efficiency, thus has the potential to reduce both total chemical consumption and system downtime. There was no deterioration in cleaning effectiveness or membrane condition which imples that sonication , has not damaged the membrane itself. Similarly, there was no change in the chemical nature of soluble proteins following sonication.

Effect of particle size on the photocatalytic activity of nanoparticulate zinc oxide

In this study, a three-stage process consisting of mechanical milling, heat treatment, and washing has been used to manufacture nanoparticulate ZnO powders with a controlled particle size and minimal agglomeration. By varying the temperature of the post-milling heat treatment, it was possible to control the average particle size over the range of 28–57 nm. The photocatalytic activity of these powders was characterized by measuring the hydroxyl radical concentration as a function of irradiation time using the spin-trapping technique with electron paramagnetic resonance spectroscopy. It was found that there exists an optimum particle size of approximately 33 nm for which the photocatalytic activity is maximized. The existence of this optimal particle size is attributable to an increase in the charge carrier recombination rate, which counteracts the increased activity arising from the higher specific surface area for a sufficiently small particle size.

Mechanochemical synthesis of nanoparticles

The results of recent investigation of the mechanochemical synthesis of inorganic nanoparticles are reviewed. It was demonstrated that, by selecting suitable chemical reaction paths, stoichiometry of starting materials and milling conditions, mechanochemical processing can be used to synthesise a wide range of nanocrystalline particles dispersed within a soluble salt matrix. Selective removal of the matrix phase by washing the resulting powder with appropriate solvents can yield nanoparticles of the desired phase. This technique has been shown to have advantages over other methods of producing nanoparticles in terms of low cost, small particle sizes, low agglomeration, narrow size distributions and uniformity of crystal structure and morphology.

UV-shielding ceramic nanoparticles synthesised by mechanochemcial processing

ZnO, TiO₂ and CeO₂ are known as UV-shielding ceramic materials that have advantages over organic UV absorbers for their photo-stability and non-hazardous nature to human bodies. However, they normally cause low transparency in the visible-light range due to light scattering by large particles, which is undesirable for many transparent UV-blocking applications in cosmetic and plastic industries. Light-scattering efficiency of particles can be drastically reduced by decreasing the particle sizes down below 100 nm. This paper reviews recent investigation on the synthesis of ZnO and CeO₂ nanoparticles by mechanochemical processing. The resulting particles had a significantly low degree of agglomeration, having mean particle sizes of ~ 25 nm and ~ 10 nm, respectively. The aqueous suspensions of the nanoparticles showed strong absorption in the UV-light range and high transmittance in the visible-light range. Mechanochemical processing offers the possibility of industrial-scale production of transparent UV-shielding ceramic particles for many applications.

Synthesis and photocatalytic activity of doped zinc oxide nanoparticles

In this study, we have investigated the effect of doping with cobalt and manganese oxide on the photocatalytic activity of nanoparticulate zinc oxide. Zinc oxide powders with controlled particle size, minimal agglomeration, and controlled chemical composition were manufactured by mechanochemical processing. The photocatalytic activity of the powders was measured using the spin trapping technique with electron paramagnetic resonance spectroscopy. It was found that the addition of cobalt oxide decreased the yield of photogenerated hydroxyl radicals. In contrast, doping with manganese oxide was found to substantially increase the rate of radical production.

Dispersion characterization of Mechanochemically Synthesized nanoparticles using UV/Vis Spectroscopy

Dispersion characterization of nanoparticles was carried out using UV/Vis spectroscopy. ZnO and CeO2 nanoparticles of sizes ranging 10 - 250 nm were investigated for slurries having various concentrations. The particles were synthesized by mechanochemical processing, which allows the formation of agglomeration-free nanoparticles. It was found that the UV/Vis spectra were highly sensitive to mean particle sizes and agglomeration states. The results showed that UV/Vis spectroscopy is a highly promising technique for studying nanoparticle dispersions having a wide range of concentrations in various media.

Laser-induced site-selective silver seeding on polyimide for electroless copper plating

Ag particles were generated on Ag+-doped polyimide film by laser direct writing, followed by selective copper deposition using the metallic silver particles as seeds. Laser irradiation caused in situ reduction and agglomeration of silver on the polyimide film. The copper lines were less uniform and compact with higher scanning velocity and the width of the deposited copper line could reach 25 mu m. Equations of the relationship between scanning velocity and connectivity of the deposited copper patterns have been derived. The process was characterised by AFM, XPS, SEM, and semiconductor characterisation system.

Dielectric properties of conducting polymer

The dielectric properties of conducting polymer composites containing polypyrrole (PPy) crushed films, PPy powder, polyaniline (PAn) base and acid powders as the dispersants and silicone rubber and vinyl ester as matrix materials have been investigated in the frequency range 2-18 GHz. The dielectric parameters such as the real part, epsiprime, and imaginary part, epsiPrime, of the permittivity and loss tangent, tandelta, increase with increasing conductivity and concentration of the dispersant. The geometrical shape of the dispersant governs the ability of conductive network formation which is indicated by a large drop in the resistivity of the composite. Also, dispersant/matrix interactions and physical properties of the matrix influence the agglomeration of the dispersant phase which, in turn, affects the dielectric properties of the composites. Flakes of PPy obtained by crushing highly conductive films and large PAn powder aggregates were unable to form a conducting network. The composites without a network of dispersant exhibit low dielectric parameters. On the other hand, high values of tan delta ranging from 0.7–1.1 were achieved for the PPy powder (15 parts)/silicone rubber composites where a conducting network was observed.

High rates of oxygen reduction over a vapor phase-polymerized PEDOT electrode

The air electrode, which reduces oxygen (O₂), is a critical component in energy generation and storage applications such as fuel cells and metal/air batteries. The highest current densities are achieved with platinum (Pt), but in addition to its cost and scarcity, Pt particles in composite electrodes tend to be inactivated by contact with carbon monoxide (CO) or by agglomeration. We describe an air electrode based on a porous material coated with poly(3,4-ethylenedioxythiophene) (PEDOT), which acts as an O₂ reduction catalyst. Continuous operation for 1500 hours was demonstrated without material degradation or deterioration in performance. O₂ conversion rates were comparable with those of Pt-catalyzed electrodes of the same geometry, and the electrode was not sensitive to CO. Operation was demonstrated as an air electrode and as a dissolved O₂ electrode in aqueous solution.

Electrospun spinel LiNi0.5Mn1.5O4 hierarchical nanofibers as 5 v cathode materials for lithium-ion batteries

Spinel LiNi0.5Mn1.5O4 hierarchical nanofibers with diameters of 200–500 nm and lengths of up to several tens of micrometers were synthesized using low-cost starting materials by electrospinning combined with annealing. Well-separated nanofiber precursors impede the growth and agglomeration of Li-Ni0.5Mn1.5O4 particles. The hierarchical nanofibers were constructed from attached LiNi0.5Mn1.5O4 nanooctahedrons with sizes ranging from 200 to 400 nm. It is proven that these Li-Ni0.5Mn1.5O4 hierarchical nanofibers exhibit a favorable electrochemical performance. At a 0.5C (coulombic) rate, it shows an initial discharge capacity of 133 mAhg_1 with a capacity retention over 94% after 30 cycles. Even at 2, 5, 10, and 15C rates, it can still deliver a discharge capacity of 115, 100, 90, and 80 mAhg_1, respectively. Compared with self-aggregated nanooctahedrons synthesized using common sol–gel methods, the LiNi0.5Mn1.5O4 hierarchical nanofibers exhibit a much higher capacity. This is owing to the fact that the self-aggregation of the unique nanooctahedron-in-nanofiber structure has been greatly reduced because of the attachment of nanopolyhedrons in the long nanofibers. This unique microstructured cathode results in the large effective contact areas of the active materials, conductive additives and fully realize the advantage of nanomaterial-based cathodes.

Molecular-level dispersion of graphene into epoxidized natural rubber: Morphology, interfacial interaction and mechanical reinforcement

The interfacial interaction of composites dominates the properties of polymeric/inorganic nanocomposites. Herein, epoxy and hydroxyl groups are introduced into the natural rubber (NR) molecular chains to anchor oxygenous functional groups on the surface of graphene oxide (GO) sheets and therefore enhance the interfacial interaction between GO and rubber. From the morphological observation and interaction analysis, it is found that epoxidized natural rubber (ENR) latex particles are assembled onto the surfaces of GO sheets by employing hydrogen bonding interaction as driving force. This self-assembly depresses restacking and agglomeration of GO sheets and leads to homogenous dispersion of GO within ENR matrix. The formation of hydrogen bonding interface between ENR and GO demonstrates a significant reinforcement for the ENR host. Compared with those of pure ENR, the composite with 0.7 wt% GO loading receives 87% increase in tensile strength and 8.7 fold increase in modulus at 200% elongation after static in-situ vulcanization.

Effects of micro-structural parameters on mechanical properties of carbon nanotube polymer nanocomposites

A comparison between the elastic modulus of carbon nanotube (CNT) polymer nano composites predicted by classical micromechanics theories, based on continuum mechanics and experimental data, was made and the results revealed a great difference. To improve the accuracy of these models, a new two-step semi-analytical method was developed, which allowed consideration of the effect of the interphase, in addition to CNT and matrix, in the modeling of nanocomposites. Based on this developed method, the inuence of microstructural parameters, such as CNT volume fraction, CNT aspect ratio, partial and complete agglomerations of CNTs, and overlap and exfoliation of CNTs, on the overall elastic modulus of nanocomposites was investigated. ©2014 Sharif University of Technology. All rights reserved.

Development of hybrid composites for automotive applications: effect of addition of SEBS on the morphology, mechanical, viscoelastic, crystallization and thermal degradation properties of PP/PS-xGnP composites

In this article, we report on a simple and cost effective approach for the development of light-weight, super-tough and stiff material for automotive applications. Nanocomposites based on PP/PS blend and exfoliated graphene nanoplatelets (xGnP) were prepared with and without SEBS. Mechanical, crystallization and thermal degradation properties were determined and correlated with phase morphology. The addition of xGnP to PP/PS blend increased the tensile modulus at the expense of toughness. The presence of xGnP increased the enthalpy of crystallization and enthalpy of fusion of PP in the blends, without affecting segmental mobility and thermal stability. Addition of polystyrene-block-poly(ethylene-ran-butylene)-block-polystyrene (SEBS) improved the toughness of PP/PS blends, but decreased the stiffness. The incorporation of xGnP into this ternary blend generated a super-tough material with improved stiffness and tensile elongation, suitable for automotive applications. It is observed that the presence of SEBS diminished the tendency of agglomeration of xGnP and their unfavorable interactions with thermoplastics, which in turn reduced the internal friction in the matrix.