Conjugated linoleic acid decreases fat accretion in pigs evaluation by dual-energy X-ray absorptiometry

Thirty female Large White × Landrace pigs (average weight 57·2 (SD 1·9) kg) were allocated to one of six dietary treatments containing 0, 1·25, 2·5, 5·0, 7·5 or 10·0 g 55 % conjugated linoleic acids (CLA) isomers (CLA-55)/kg diet and fed for 8 weeks. Each pig was scanned at 0, 28 and 56 d and again at post slaughter using dual-energy X-ray absorptiometry (DXA) to determine the temporal pattern of body composition responses. Values determined by DXA were adjusted using regression equations generated from validation experiments between chemically and DXA-predicted values. Overall, there was a significant linear reduction in fat content with the increasing levels of CLA in the diet (P=0·007, P=0·011, P=0·008 at week 4, week 8 and for the carcass, respectively). The greatest improvement was recorded at the early stages of CLA supplementation and for the highest dose of CLA (week 4, -19·2 % compared with week 8, -13·7 %). In the first 4 weeks of feeding CLA, pigs receiving 10 g CLA-55/kg diet deposited 93 g less fat/d than pigs fed basal diets (P=0·002) compared with only 6 g less fat than control animals in the final 4 weeks. Lean content and lean deposition rate were maximised at 5 and 2·5 g CLA-55/kg diet for the first 4 weeks (P=0·016) and the final 4 weeks of treatment (P=0·17), respectively. DXA estimates of bone mineral content and bone mineral density were not affected by CLA supplementation throughout the experiment. These data demonstrate that dietary CLA decreases body fat in a dose-dependent manner and that the response is greatest over the initial 4 weeks of treatment.

Disk-electrospinning of PVA nanofibres

In this study, we demonstrated that a thin aluminium disk can be used as nozzle to electrospin PVA nanofibres on a large-scale. A schematic of this electrospinning system and a SEM image of as-spun PVA nanofibers are shown in Figure 1. The lower part of the disk is inside a bath containing the polymer solution, which is connected to a high voltage powder supply. During electrospinning, the disk rotates and picks up a thin layer of electrically charged PVA solution. A large number of fibres are then electrospun simultaneously from two sides of tile disk and deposited on the electrode collector.
With the small prototype unit we used, the fibre production rate can be as high as 6.0 which is about 270 times higher than that of a corresponding normal needle electrospinning system (0.022g/hr). The effects of appliedb voltage, the distance between the disk nozzle and collector, and PVA concentration on the fibre morphology were examined. The dependency of fibre diameter on the PVA concentration showed a similar trend to that for a conventional electrospinning system using a syringe needle nozzle, but the diameter distribution was wider for the disk electrospun fibres in this study.
The profiles of electric field strength in disk electrospinning showed considerable dependence on the disk thickness, with a thin disk exhibiting similar electric field profile to
that of a needle electrospinning system, but a thick disk (cylinder) exhibiting levelled electric field between the disk and the collector. PVA nanofibres electrospun from disk electrospinning were compared to that electrospun from syringe needle and metal cylinder nozzles.

Needleless electrospinning. I. A comparison of cylinder and disk nozzles

In this study, we demonstrated the needleless electrospinning of poly(vinyl alcohol) (PVA) nanofibers with two nozzles, a rotating disk and a cylinder, and examined the effect of the nozzle shape on the electrospinning process and resultant fiber morphology. The disk nozzle needed a relatively low applied voltage to initiate fiber formation, and the fibers were mainly formed on the top disk edge. Also, the PVA concentration had little influence on the disk electrospinning process (up to 11 wt %). In comparison, the cylinder electrospinning showed a higher dependence on the applied voltage and polymer concentration. The fibers were initiated from the cylinder ends first and then from the entire cylinder surface only if the applied voltage were increased to a certain level. With the same polymer solution, the critical voltage needed to generate nanofibers from the disk nozzle was lower than that needed to generate nanofibers from the cylinder. Both electrospinning systems could produce uniform nanofibers, but the fibers produced from the disk nozzle were finer than those from the cylinder when the operating conditions were the same. A thin disk (8 cm in diameter and 2 mm thick) could produce nanofibers at a rate similar to that of a cylinder of the same diameter but 100 times wider (i.e., 20 cm long). Finite element analysis of electric field profiles of the nozzles revealed a concentrated electric field on the disk edge. For the cylinder nozzle, an uneven distribution of the electric field intensity profile along the nozzle surface was observed. The field lines were mainly concentrated on the cylinder ends, with a much lower electric field intensity formed in the middle surface area. At the same applied voltage, the electric field intensity on the disk edge was much higher than that on the cylinder end. These differences in the electric field intensity profiles could explain the differences in the fiber fineness and rate of the nanofibers produced from these two nozzles. These findings will benefit the design and further development of large-scale electrospinning systems for the mass production of nanofibers for advanced applications.

Oxygen reduction reaction activity of La-based perovskite oxides in alkaline medium : a thin-film rotating ring-disk electrode study

In this work, LaMO₃ and LaNi_0.5M_0.5O₃ (M = Ni, Co, Fe, Mn and Cr) perovskite oxide electrocatalysts were synthesized by a combined ethylenediaminetetraacetic acid-citrate complexation technique and subsequent calcinations at 1000 °C in air. Their powder X-ray diffraction patterns demonstrate the formation of a specific crystalline structure for each composition. The catalytic property of these materials toward the oxygen reduction reaction (ORR) was studied in alkaline potassium hydroxide solution using the rotating disk and rotating ring-disk electrode techniques. Carbon is considered to be a crucial additive component because its addition into perovskite oxide leads to optimized ORR current density. For LaMO₃ (M = Ni, Co, Fe, Mn and Cr)), in terms of the ORR current densities, the performance is enhanced in the order of LaCrO₃, LaFeO₃, LaNiO₃, LaMnO₃, and LaCoO3. For LaNi_0.5M_0.5O₃, the ORR current performance is enhanced in the order of LaNi_0.5Fe_0.5O₃, LaNi_0.5Co_0.5O₃, LaNi_0.5Cr_0.5O₃, and LaNi_0.5Mn_0.5O₃. Overall, LaCoO₃ demonstrates the best performance. Most notably, substituting half of the nickel with cobalt, iron, manganese, or chromium translates the ORR to a more positive onset potential, suggesting the beneficial catalytic effect of two transition metal cations with Mn as the most promising candidate. Koutecky–Levich analysis on the ORR current densities of all compositions indicates that the four-electron pathway is favored on these oxides, which are consistent with hydroperoxide ion formation of <2%.