Microstructures, mechanical and corrosion properties and biocompatibility of as extruded Mg-Mn-Zn-Nd alloys for biomedical applications

Extruded Mg-1Mn-2Zn-xNd alloys (x=0.5, 1.0, 1.5 mass %) have been developed for their potential use as biomaterials. The extrusion on the alloys was performed at temperature of 623K with an extrusion ratio of 14.7 under an average extrusion speed of 4mm/s. The microstructure, mechanical property, corrosion behavior and biocompatibility of the extruded Mg-Mn-Zn-Nd alloys have been investigated in this study. The microstructure was examined using X-ray diffraction analysis and optical microscopy. The mechanical properties were determined from uniaxial tensile and compressive tests. The corrosion behavior was investigated using electrochemical measurement. The biocompatibility was evaluated using osteoblast-like SaOS2 cells. The experimental results indicate that all extruded Mg-1Mn-2Zn-xNd alloys are composed of both α phase of Mg and a compound of Mg7Zn3 with very fine microstructures, and show good ductility and much higher mechanical strength than that of cast pure Mg and natural bone. The tensile strength and elongation of the extruded alloys increase with an increase in neodymium content. Their compressive strength does not change significantly with an increase in neodymium content. The extruded alloys show good biocompatibility and much higher corrosion resistance than that of cast pure Mg. The extruded Mg-1Mn-2Zn-1.0Nd alloy shows a great potential for biomedical applications due to the combination of enhanced mechanical properties, high corrosion resistance and good biocompatibility.

Phase morphology, thermomechanical, and crystallization behavior of uncompatibilized and PP-g-MAH compatibilized polypropylene/polystyrene blends

In this article, we discuss the phase morphology, thermal, mechanical, and crystallization properties of uncompatibilized and compatibilized polypropylene/polystyrene (PP/PS) blends. It is observed that the Young's modulus increases, but other mechanical properties such as tensile strength, flexural strength, elongation at break, and impact strength decrease by blending PS to PP. The tensile strength and Young's modulus of PP/PS blends were compared with various theoretical models. The thermal stability, melting, and crystallization temperatures and percentage crystallinity of semicrystalline PP in the blends were marginally decreased by the addition of amorphous PS. The presence of maleic anhydride-grafted polypropylene (compatibilizer) increases the phase stability of 90/10 and 80/20 blends by preventing the coalescence. Hence, finer and more uniform droplets of PS dispersed phases are observed. The compatibilizer induced some improvement in impact strength for the blends with PP matrix phase, however fluctuations in modulus, strength and ductility were observed with respect to the uncompatibilized blend. The thermal stability was not much affected by the addition of the compatibilizer for the PP rich blends but shows some decrease in the thermal stability of the blends, where PS forms the matrix. On the other hand, the % crystallinity was increased by the addition of compatibilizer, irrespective of the blend concentration.

Effect of strain ageing on the mechanical properties of partially damaged structural mild steel

ABSTRACT
This paper addresses the strain ageing effects on the mechanical properties of the partially damaged structural mild steel. Since repairing partly damaged structures may not occur immediately, the strain ageing effect can significantly influence the structural behaviour. The changes due to this effect have not so far been considered in the civil engineering design guidelines. In order to investigate strain ageing effects, two-stage experimental tests are carried out on the mild-steel specimens. In the first stage, partial damage is made using quasi-static loading. During the second stage, the strength and ductility of the specimens are examined after 2 and 7 days ‘ageing’ at room temperature and the results are compared with the corresponding no-age samples. The microstructure of the specimens is examined using scanning electron microscopy (SEM). To illustrate the effect of strain ageing on the global behaviour of steel structures, a numerical example is provided in which strain ageing impacts on loading capacity and deflection of a steel beam. Finally, the stress–strain relation of partially damaged mild-steel material incorporating strain ageing effects is expressed by calibrating the parameters of Ramberg–Osgood model.

Structure-property relationships in nylon 6 nanocomposites based on octaphenyl-, dodecaphenyl-POSS, montmorillonite, and their combinations

Binary and ternary nanocomposites were produced by incorporating, via melt compounding, two types of octa-and dodecaphenyl substituted polyhedral oligomeric silsesquioxanes (POSS), montmorillonite (MMT), and combinations of POSS with MMT into nylon 6. The tensile, flexural, and dynamic thermo-mechanical properties of these materials were characterized and their structure-property relationships discussed. The results show that the losses in ductility and toughness experienced after inclusion of MMT into nylon 6 can be balanced out by co-mixing MMT with the dodecaphenyl- POSS to produce a ternary nanocomposite. This trend however was less pronounced in the ternary MMT/octaphenyl-POSS system. Analysis of the microstructure organization in these materials using XRD and SEM sheds some light on understanding the differences in behavior. Both types of POSS particles mixed alone in nylon 6 were found to be polydisperse (500 nm to a few microns in size) and locally aggregated, yielding materials with similar mechanical performance. The co-mixing of MMT with the octaphenyl- POSS served to break down the POSS crystal aggregates, enhancing their micro-mechanical reinforcing action. On the other hand, the POSS crystals were not affected in the MMT/dodecaphenyl-POSS system, which led to improving their toughening ability.

Experimental study of damage evolution in cuboid stirrup-confined concrete

This paper presents an experimental study on cuboid stirrup-confined concrete specimens under uniaxial monotonic loading and cyclic loading. The effects of stirrup volume ratio, stirrup yield strength, and concrete strength on damage evolution of the stirrup-confined concrete were investigated. The experimental results showed that the strength and ductility of concrete are improved by appropriate arrangement of the stirrup confinement. Firstly, with the increase of the stirrup volume ratio, the damage evolution of concrete can be relatively restrained. Secondly, higher stirrup yield strength usually leads to larger confining pressures and slower damage evolution. In contrast, higher concrete strength leads to higher brittleness, which accelerates damage evolution. Based on the experimental data, a plastic strain expression is obtained through curve fitting, and a damage evolution equation for stirrup-confined concrete is proposed by introducing a confinement factor (C). The comparisons results demonstrated that the proposed damage evolution curve can accurately describe the experimental results.

Gradient structure produced by three roll planetary milling: numerical simulation and microstructural observations

In this study a gradient grain structure was produced by processing rod billets through three roll planetary milling (also known as PSW process). This kind of gradient structure is reported to provide an excellent combination of strength and ductility owing to an ultrafine-grained surface layer and a coarse-grained interior of the billet. Specifically, copper rod samples were subjected to up to six passes of PSW at room temperature. To study the evolution of the microstructure during the deformation, microhardness measurements and Electron Backscatter Diffraction (EBSD) analysis were performed after one, three and six passes. Additionally, the distributions of the equivalent stress during PSW and the equivalent strain after processing were studied by finite element analysis using the commercial software QFORM. The results showed the efficacy of PSW as a means of imparting a gradient ultrafine-grained structure to copper rods. A good correlation between the simulated equivalent strain distribution and the measured microhardness distribution was demonstrated.

Simultaneous improvement in the strength and corrosion resistance of Al via high-energy ball milling and Cr alloying

The corrosion resistance and mechanical properties of nanocrystalline aluminium (Al) and Al-20. wt.%Cr alloys, synthesized by high-energy ball milling followed by spark plasma sintering, were investigated. Both alloys exhibited an excellent combination of corrosion resistance and compressive yield strength, which was attributed to the nanocrystalline structure, extended solubility, uniformly distributed fine particles, and homogenous microstructure induced by high-energy ball milling. This work demonstrates the possibilities of developing ultra-high strength Al alloys with excellent corrosion resistance, exploiting conventionally insoluble elements or alloying additions via suitable processing routes.

Enhanced mechanical response of an ultrafine grained Ti-6Al-4V alloy produced through warm symmetric and asymmetric rolling

An equiaxed ultrafine-grained (UFG) microstructure was successfully produced in a Ti-6Al-4V alloy with an average grain size of 110-230. nm through symmetric and asymmetric warm rolling of a martensitic starting microstructure. The UFG material displayed a combination of ultrahigh strength and ductility at room temperature. Compared with the conventional symmetric rolling, the asymmetric rolling process led to a more pronounced effect of microstructure refinement and a higher tensile ductility. The optimum mechanical response was obtained though the asymmetric rolling at 70% reduction, offering an ultimate tensile strength of 1365. MPa and a total elongation of ~23%. Apart from the magnitude of grain refinement, the inclination of basal texture component from the normal towards the rolling direction during asymmetric rolling and possible strain induced β to martensite transformation may concurrently contribute to a remarkable tensile strength-ductility balance.

Experimental investigation on bonding properties of reactive liquid rubber epoxy in CFRP retrofitted concretet members

The load bearing capacity of aging reinforced concrete structures, such as bridges, is increasingly extended with the use of Carbon Fibre Reinforced Polymer (CFRP). Premature failure, which is attributed to the rigid behaviour of the bonding agent (epoxy resin) and the high stresses at the interface region, can occur because of the debonding of CFRP sheets from host surfaces. To overcome the debonding issue, the epoxy resin is modified by different reactive liquid polymers to improve its toughness, flexibility, adhesion, and impact resistance. This study reports the usage of two reactive liquid polymers, namely, liquid Carboxyl-Terminated Butadiene-Acrylonitrile (CTBN) and liquid Amine-Terminated Butadiene-Acrylonitrile (ATBN), to improve the mechanical properties of the commercially available MBrace saturant resin when added to a ratio of 100:30 by weight. The neat and modified epoxies were analysed using the Dynamic Mechanical Thermal Analysis (DMTA) to determine and compare the storage modulus and glass transition temperatures of these materials. Moreover, the bonding strength of neat and modified epoxies was evaluated through single-lap shear tests on CFRP sheets bonded to concrete prisms. The results indicate that the modified resins exhibited improved ductility and toughness and became reasonably flexible compared with the neat epoxy resin. The improved properties will help delay the premature debonding failure in CFRP retrofitted concrete members.

Experimental investigation on CFRP-steel bond properties using ionic liquid

Solving the problem of pre mature debonding of CFRP retrofitted structure is a main concern for most of structural engineers nowadays. Reducing the brittleness of the bonding agent at the CFRP/concrete interface is a major factor to avoid this behaviour. In this research, the effect of modifying the bonding agent using different percentages of ionic liquid (IL) is investigated. This paper reports on an experimental investigation on the behaviour of modified epoxy resin with IL. Steel plates were used as hosting surface of the CFRP laminates, the laminates were attached to the steel surface using the IL modified epoxy. The shear mechanism at the interface of CFRP laminates to steel plates is discussed considering the relationship between the shear and the slip at the interface. The shear stress- displacement are traced for all specimens, the results are compared with control test prepared using unmodified epoxy. A 20% IL modified epoxy shows improved Behaviour. The improvement is with respect to ductility enhancement of the overall behaviour.

Mechanical properties and microstructure of powder metallurgy Ti-xNb-yMo alloys for implant materials

In this study, a series of Ti-xNb-yMo (x = 5-40 wt.% in 5 wt.% increments; and y = 3, 5, 10 wt%) alloys were fabricated by powder metallurgy and studied with respect to their microstructures, compressive mechanical properties and hardness. Increases in Nb and Mo content led to decreases in compressive and yield strengths, elastic modulus and hardness of the sintered alloys. Among the studied alloys, Ti-10Nb-3Mo alloy exhibited the optimum combination of strength and ductility. Alloys with a lower amount of Nb (≤ 25 wt.%) and Mo (≤ 5 wt.%) developed Widmanstätten structure, while further increase in Nb and Mo additions led to the microstructure predominantly consisting of β phase with varying regions of α + β phase. The effects of sintering temperature on elastic modulus and hardness were also investigated for Ti-xNb-3Mo alloys.

Transesterification induced mechanical properties enhancement of PLLA/PHBV bio-alloy

In order to improve the miscibility and mechanical properties of poly(l-lactic acid) (PLLA) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) bio-alloy, small amount of transesterification catalyst, zinc acetate was added in the melt blending process. We show that the PLLA-PHBV copolymer generated during the melt blending significantly improves the miscibility and therefore enhances the mechanical properties of the product. Dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), and tensile tests were performed to study the miscibility and mechanical properties of the blends. Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC) were used to reveal the molecular structural, and molecular weight changes of PLLA and PHBV after melt mixing with zinc acetate. SEM and FTIR results have clearly shown that the PLLA-PHBV copolymer generated from transesterification reaction acted as a compatibilizer and therefore resulted in an improved interfacial miscibility and ductility of PLLA/PHBV blend. In our mechanistic study, a competition between the PLLA/PHBV transesterification reaction and the thermal decomposition of PHBV was identified for the first time. On the basis of these observations, a new mechanism of transesterification reaction was proposed.

An investigation of major factor of influence of strength gain or loss of geopolymer when exposed to 800° C

When fly ash based geopolymer mortars were exposed to an elevated temperature of 800oC, it was found that the strength after the exposure sometimes decreased, but at other times increased compared to the original strength. The aim of this investigation is to find the reason for this contrasting behaviour. Fol-lowing exposure to high temperature, residual strengths of specimens prepared with two different fly ashes, with initial strengths ranging from 5MPa to 60MPa, were investigated. The parameter that was found to have a major influence on the contrasting behaviour was the ductility of the mortars. The results indicate that the higher the ductility the lower the strength loss. This correlation is attributed to the fact that mortars with high ductility could provide higher capacity to accommodate thermal incompatibility than mortars with low ductil-ity. Beyond the particular threshold of ductility, some mortars even increased strength after the exposure, pos-sibly due to sintering.

Enhanced superplasticity of magnesium alloy AZ31 obtained through equal-channel angular pressing with back-pressure

Excellent superplastic elongations (in excess of 1,200%) were achieved in a commercial cast AZ31 alloy processed by low temperature equal-channel angular pressing (ECAP) with a back-pressure to produce a bimodal grain structure. In contrast, AZ31 alloy processed by ECAP at temperatures higher than 200 °C showed a reasonably uniform grain structure and relatively low ductility. It is suggested that a bimodal grain structure is advantageous because the larger grains contribute to strain hardening thus delaying the onset of necking, while grain boundary sliding associated with small grains provides a stabilizing effect due to enhanced strain rate sensitivity. © 2008 Springer Science+Business Media, LLC.

Processing and properties of ultrafine-grain aluminium alloy 6111 sheet

The equal channel angular processing (ECAP) technique has been applied to an automotive aluminium alloy sheet (A6111). The technique utilizes a machine that was specially designed for this purpose at Monash University. It was determined that ECAP is able to refine the grain size of the sheet, diminish the detrimental as-rolled texture components in the sheet and retain an acceptable level of bi-axial ductility such as is required during the automotive forming process. Experiments were carried out on annealed, as-received sheets that were subjected to either one or two passes through the ECAP machine. For the second ECAP pass, the sheet could be processed in the same orientation as the first pass (route A) or it could be rotated 180° about the direction of feeding (route C). It was determined that route A produced marginally improved properties compared to sheet processed via route C, and that due to the frictional heating generated during the second pass, a significant amount of recovery occurred in the sheet such that an improved combination of texture and formability resulted after two passes compared to the same sheet exposed to only a single pass.