Asymmetric rolling of interstitial-free steel using differential roll diameters. Part I : mechanical properties and deformation textures

IF steel sheets were processed by conventional symmetric and asymmetric rolling (ASR) at ambient temperature. The asymmetry was introduced in a geometric way using differential roll diameters with a number of different ratios. The material strength was measured by tensile testing and the microstructure was analyzed by optical and transmission electron microscopy as well as electron backscatter diffraction (EBSD) analysis. Texture was also successfully measured by EBSD using large surface areas. Finite element (FE) simulations were carried out for multiple passes to obtain the strain distribution after rolling. From the FE results, the velocity gradient along selected flow lines was extracted and the evolution of the texture was simulated using polycrystal plasticity modeling. The best mechanical properties were obtained after ASR using a roll diameter ratio of 2. The textures appeared to be tilted up to 12 deg around the transverse direction, which were simulated with the FE-combined polycrystal plasticity modeling in good agreement with measurements. The simulation work revealed that the shear component introduced by ASR was about the same magnitude as the normal component of the rolling strain tensor.

Review short: Cath Keneally's eaten cold

In The Sacred Wood: Essays on Poetry and Criticism, T. S. Eliot famously wrote, ‘Immature poets imitate; mature poets steal; bad poets deface what they take, and good poets make it into something better, or at least something different.’ Cath Kenneally’s eaten cold offers a chain of indelible response-poems to New Zealand poet Janet Charman’s book, cold snack. In Kenneally’s collection, ‘Meanings perpetually eingeschachtelt into meanings’, creating new and original poetry that riffs off Charman’s book without ‘imitating’ or ‘defacing’ it.

Basal metabolic rate of canidae from hot deserts to cold arctic climates

Canids form the most widely distributed family within the order Carnivora, with members present in a multitude of different environments from cold arctic to hot, dry deserts. We reviewed the literature and compared 24 data sets available on the basal metabolic rate (BMR) of 12 canid species, accounting for body mass and climate, to examine inter- and intraspecific variations in mass-adjusted BMR between 2 extreme climates (arctic and hot desert). Using both conventional and phylogenetically independent analysis of covariance, we found that canids from the arctic climate zone had significantly higher mass-adjusted BMR than species from hot deserts. Canids not associated with either arctic or desert climates had an intermediate and more variable mass-adjusted BMR. The climate effect also was significant at the intraspecific level in species for which we had data in 2 different climates. Arctic and desert climates represent contrasting combinations of ambient temperatures and water accessibility that require opposite physiological adaptations in terms of metabolism. The fact that BMR varies within species when individuals are subjected to different climate regimes further suggests that climate is an important determinant of BMR.

Cryo-rolling and formability of 2024 aluminium

Sheets of precipitate hardenable 2024 aluminium have been processed by rolling at liquid nitrogen temperature in order to refine the microstructure. A number of different aging/heat treating procedures have been utilised that have resulted in significantly different mechanical properties. The cryo-rolled material was heat treated at 150 °C for varying times and the resulting mechanical properties evaluated as a function of this holding time. The resulting properties were found to be strongly influenced by precipitates that formed either during the aging step, rolling process or the subsequent heat treatment. The formability of the cryo-rolled and heat treated material has been investigated using a limiting dome height test (Erichsen cupping test).

Asymmetric rolling of interstitial-free steel using differential roll diameters. Part II : microstructure and annealing effects

The effects of annealing on the microstructure, texture, tensile properties, and R value evolution of an IF steel sheet after room-temperature symmetric and asymmetric rolling were examined. Simulations were carried out to obtain R values from the experimental textures using the viscoplastic self-consistent polycrystal plasticity model. The investigation revealed the variations in the textures due to annealing and symmetric/asymmetric rolling and showed that the R values correlate strongly with the evolution of the texture. An optimum heat treatment for the balance of strength, ductility, and deep drawability was found to be at 873 K (600 _C) for 30 minutes.

Cycling time to failure is better maintained by cold than contrast or thermoneutral lower-body water immersion in normothermia

Purpose
To examine the effects of four commonly used recovery treatments applied between two bouts of intense endurance cycling on the performance of the second bout in normothermia (~21 °C).

Methods
Nine trained men completed two submaximal exhaustive cycling bouts (Ex1 and Ex2: 5 min at ~50 % V˙O2 peak, followed by 5 min at ~60 % V˙O2 peak and then ~80 % V˙O2 peak to failure) separated by 30 min of (a) cold water immersion at 15 °C (C15), (b) contrast water therapy alternating 2.5 min at 8 °C and 2.5 min at 40 °C (CT), (c) thermoneutral water immersion at 34 °C (T34) and (d) cycling at ~40 % V˙O2 peak (AR).

Results
Exercise performance, cardiovascular and metabolic responses during Ex1 were similar among all trials. However, time to failure (~80 % V˙O2 peak bout) during Ex2 was significantly (P < 0.05) longer in C15 (18.0 ± 1.6) than in CT (14.5 ± 1.5), T34 (12.4 ± 1.4) and AR (10.6 ± 1.0); and it was also longer (P < 0.05) in CT than AR. Core temperature and heart rate were significantly (P < 0.05) lower during the initial ~15 min of Ex2 during C15 compared with all other conditions but they reached similar levels at the end of Ex2.

Conclusions
A 30 min period of C15 was more beneficial in maintaining intense submaximal cycling performance than CT, T34 and AR; and CT was also more beneficial than T34 and AR. These effects were not mediated by the effect of water immersion per se, but by the continuous (C15) or intermittent (CT) temperature stimulus (cold) applied throughout the recovery.

A study on compressive anisotropy and nonassociated flow plasticity of the AZ31 Magnesium Alloy in hot rolling

Effect of anisotropy in compression is studied on hot rolling of AZ31 magnesium alloy with a three-dimensional constitutive model based on the quadratic Hill48 yield criterion and nonassociated flow rule (non-AFR). The constitutive model is characterized by compressive tests of AZ31 billets since plastic deformations of materials are mostly caused by compression during rolling processes. The characterized plasticity model is implemented into ABAQUS/Explicit as a user-defined material subroutine (VUMAT) based on semi-implicit backward Euler's method. The subroutine is employed to simulate square-bar rolling processes. The simulation results are compared with rolled specimens and those predicted by the von Mises and the Hill48 yield function under AFR. Moreover, strip rolling is also simulated for AZ31 with the Hill48 yield function under non-AFR. The strip rolling simulation demonstrates that the lateral spread generated by the non-AFR model is in good agreement with experimental data. These comparisons between simulation and experiments validate that the proposed Hill48 yield function under non-AFR provides satisfactory description of plastic deformation behavior in hot rolling for AZ31 alloys in case that the anisotropic parameters in the Hill48 yield function and the non-associated flow rule are calibrated by the compressive experimental results.