Dynamic recrystallization of austenite in Ni-30 Pct Fe model alloy : microstructure and texture evolution

The microstructure and crystallographic texture development in an austenitic Ni-30 pct Fe model alloy was investigated within the dynamic recrystallization (DRX) regime using hot torsion testing. The prominent DRX nucleation mechanism was strain-induced grain boundary migration accompanied by the formation of large-angle sub-boundaries and annealing twins. The increase in DRX volume fraction occurred through the formation of multiple twinning chains. With increasing strain, the pre-existing Σ3 twin boundaries became gradually converted to general boundaries capable of acting as potent DRX nucleation sites. The texture characteristics of deformed grains resulted from the preferred consumption of high Taylor factor components by new recrystallized grains. Similarly, the texture of DRX grains was dominated by low Taylor factor components as a result of their lower consumption rate during the DRX process. The substructure of deformed grains was characterized by “organized,” banded subgrain arrangements, while that of the DRX grains displayed “random,” more equiaxed subgrain/cell configurations.

Microstructure and mechanical properties of thermomechanically processed TRIP steel

The strengthening mechanism responsible for the unique combination of ultimate tensile strength and elongation in a multiphase Fe-0.2C-1.5Mn-1.2Si-0.3Mo-0.6Al-0.02Nb (wt%) steel was studied. The microstructures with different volume fractions of polygonal ferrite, bainite and retained austenite were simulated by controlled thermomechanical processing. The interrupted tensile test was used to study the bainitic ferrite, retained austenite and polygonal ferrite behaviour as a function of plastic strain. X-ray analysis was used to characterise the volume fraction and carbon content of retained austenite. Transmission electron microscopy was utilised to analyse the effect of bainitic ferrite morphology on the strain induced transformation of retained austenite and retained austenite twinning as a function of strain in the bulk material. The study has shown that the austenite twinning mechanism is more preferable than the transformation induced plasticity (TRIP) mechanism during the early stages of deformation for a microstructure containing 15% polygonal ferrite, while the transformation induced plasticity effect is the main mechanism when there is 50% of polygonal ferrite in the microstructure. The bainitic ferrite morphology affects the deformation mode of retained austenite during straining. The polygonal ferrite behaviour during straining depends on dislocation substructure formed due to the deformation and the additional mobile dislocations caused by the TRIP effect. Operation of TRIP or twinning mechanisms depends not only on the chemical and mechanical stability of retained austenite, but also on the interaction of the phases during straining.

Softening mechanisms in two duplex stainless steels deformed in hot torsion

The aim of the present work was to undertake a detailed investigation of the softening mechanisms during hot deformation of a 21Cr-10Ni-3Mo (steel A) and a 21Cr-8Ni-3Mo (steel B) austenite/ferrite duplex stainless steels containing about 60% and 30% of austenite, respectively. The steels were subjected to hot deformation in torsion performed at 900 ºC and 1200 ºC using a strain rate of 0.7 s-1 to several strain levels. Quantitative optical and transmission electron microscopy were used in the investigation. Austenite was observed to soften via dynamic recovery (DRV) and dynamic recrystallisation (DRX) accompanied by DRV for the deformation temperatures of 900 °C and 1200 °C, respectively, for the both steels studied. DRX of austenite largely occurred through strain-induced grain boundary migration, complemented by (multiple) twinning, and developed significantly faster in steel A than in steel B, indicating that considerably larger strains partitioned into austenite in the former steel during deformation at 1200 °C. The above softening mechanism was accompanied by the formation of DRX grains from subgrains along the austenite/ferrite interface and by large-scale subgrain coalescence. At 900°C, stressassisted phase transitions between austenite and ferrite were observed, characterised by dissolution of the primary austenite, formation of Widmanstätten secondary austenite and gradual globularisation of the microstructure with increasing strain. These processes appeared to be significantly more widespread in steel B. The softening mechanism within ferrite for the both steels studied was classified as “continuous DRX”, characterised by a gradual increase in misorientations between neighbouring subgrains with strain, for the both deformation temperatures.

EBSD analysis of deformation modes in Mg-3Al-1Zn

Researches the use of the electron back scattered diffraction analysis (EBSD) technique in investigating deformation modes in the magnesium alloy Mg-3Al-1Zn. Results showed the importance of non-basal slip, compression and double twinning during deformation of rolled Mg-3Al-1Zn. In as-cast material, twinning behaviour was more varied and complicated and could even occur upon unloading.

Atom probe tomography of solute distributions in mg-based alloys

Atom probe tomography (APT) has been carried out on three magnesium-based alloys: M1 (Mg-1 wt pct Mn), AZ31(Mg-3 pct Al-1 pct Zn), and ME10 (Mg-1 pct Mn- 0.4 pct misch metal). The aims of this experiment were to measure the composition of the matrix and to investigate solute clustering in the matrix of the three different alloys. For AZ31, the matrix composition was variable but close to the bulk composition. For ME10 and M1, the matrix was depleted in alloying additions, with the remainder residing in precipitates. Most alloying additions were found to exhibit clustering to some extent, with misch metal having the strongest partitioning behavior to clusters. Solute clusters did not appear to affect mechanical twinning. It has been proposed that the clustering behavior of misch metal contributes to its ability to modify the recrystallization texture.

Effect of particles on the formation of deformation twins in a magnesium-based alloy

The deformation behaviour of the age hardenable alloy Mg–5%Zn after different precipitation treatments has been examined. It has been found that during compressive deformation, fine particles increase the number of twins that form, but reduce the size and total volume fraction of twins. Visco-plastic selfconsistent modelling has been used to show that the presence of precipitates hardens the twin and prismatic slip systems more than the basal slip system. It is proposed that because the {10 ¯12} twin requires basal slip to accommodate the twinning shear, this twin type will always be hardened equal to, or more than, the basal slip system in response to precipitation.

The Challenge of inhomogeneous deformation in magnesium and its alloys

It is shown that wrought magnesium alloys display a number of significant types of deformation inhomogeneities. These are influenced by the variation in the ease of basal slip amongst grains, micro-textures, shear banding, twinning and grain boundary sliding. Key features of each of these effects are examined and their engineering consequences and challenges are identified.

Deformation mechanisms in mg alloys and the challenge of extending room-temperature Plasticity

Magnesium alloys show promise for application in formed components where weight saving is an advantage. In most instances forming is carried out at elevated temperatures. However, there are considerable gains to be had if forming can be carried out under ambient conditions. The present article outlines some of the difficulties that lie in the way of achieving this objective. The underlying metallurgical characteristics of the issues are considered and means for overcoming them are discussed. It is concluded that a combination of microstructure and texture control remains a promising strategy.

Combined in situ neutron diffraction and acoustic emission of twin nucleation & twin growth in extruded ZM20 Mg alloy

In the present work in situ neutron diffraction and acoustic emission were used concurrently to study deformation twinning in two ZM20 Mg alloys with significantly different grain sizes at room temperature. The combination of these techniques allows differentionation between the twin nucleation and the twin growth mechanisms. It is shown, that yielding and immediate post-yielding plasticity in compression is governed primarily by twin nucleation, whereas the plasticity at higher strains is governed by twin growth. The current results further suggest that yielding by twinning happens in a slightly different manner in the fine-grained as compared to the coarse-grained alloy.

Atomic scale simulation of deformation in magnesium single crystals

The deformation behaviour of magnesium single crystals under plane strain conditions has been examined using molecular dynamics modelling. The simulations were based on an existing atomic potential for magnesium taken from the literature. A strain of 10% was applied at rates of 3x10⁹s^-1 and 3x10⁷s^-1. The simulations predicted the formation of mechanical twins that accommodated extension in the c-axis direction of the hexagonal unit cell. However, the predicted twin is not of the same kind found in magnesium, but is that commonly observed in titanium. It is believed that further analysis of the physical properties predicted by this interatomic potential will shed more light on the atomic processes controlling twinning in Magnesium alloys. It also highlights the need for improvements to the interatomic potential such that more accurate deformation behaviour can be attained.

Constitutive modeling of TWIP steel in uni-axial tension

High Mn steels demonstrate an exceptional combination of high strength and ductility due to their high work hardening rate during deformation. The microstructure evolution and work hardening behavior of Fe18Mn0.6C1.5Al TWIP steel in uni-axial tension were examined. The purpose of this study was to determine the contribution of all the relevant deformation mechanism : slip, twinning and dynamic strain aging. Constitutive modeling was carried out based on the Kubin-Estrin model, in which the densities of mobile and forest dislocations are coupled in order to account for the continuous immobilization of mobile dislocations during straining. These coupled dislocation densities were also used for simulating the contribution of dynamic strain aging on the flow stress. The model was modified to include the effect of twinning.

"Rare Earth" texture development in extruded Mg-based alloys

This data collection addresses the problem of low ductility in magnesium alloys, preventing their wider use. It examines a series of dilute alloys in order to determine the effect of composition on the extrusion behaviour and texture, and on the room temperature tensile ductility.

Electron backscatter diffraction (EBSD) map of AZ31 compressed to 1% strain at room temperature in a direction parallel to the extrusion direction

The collection contains an EBSD map of AZ31 compressed to 1% strain at room temperature in a direction parallel to the extrusion direction. The map was collected as part of an investigation into the role of twinning in the occurrence of a yield point elongation during deformation.