An analysis of microband orientation in hot deformed aluminium alloy AA5052 using forward and reverse torsion

The effects of strain path reversal on the macroscopic orientation of microbands in AA5052 have been studied using high resolution electron backscatter diffraction. Deformation was carried using two equal steps of forward/forward or forward/reverse torsion at a temperature of 300°C and strain rate of 1s-1 to a total equivalent tensile strain of 0.5. In both cases microbands were found in the majority of grains examined with many having more than one set. The microbands appear to cluster at specific angles to the macroscopic deformation. For the forward/forward condition microbands clustered around -20° and +45° to the maximum principle stress direction and at ± 30-35° to the principal strain direction. For the forward/reverse condition significantly more spread in microband angle was observed though peaks were visible at ±35° with respect to principal stress direction and at -40° and +30° with respect to the principal strain direction of the reverse torsion. This suggests the microbands formed in the forward deformation have or are dissolving and any new microbands formed are related to the deformation conditions of the final strain path.

EBSD study of the orientation dependence of substructure characteristics in a model Fe-30wt%Ni alloy subjected to hot deformation

The aim of the present investigation was to determine the orientation dependence of substructure characteristics in an austenitic Fe−30wt%Ni model alloy subjected to hot plane strain compression. Deformation was carried out at a temperature of 950 °C using a strain rate of 10 s^₋₁ to equivalent strain levels of approximately 0.2, 0.4, 0.6 and 0.8. The specimens obtained were analysed using a fully automatic electron backscatter diffraction technique. The crystallographic texture was characterized for all the strain levels studied and the subgrain structure was quantified in detail at a strain of 0.4. The substructure characteristics displayed pronounced orientation dependence. The major texture components, namely the copper, S, brass, Goss and rotated Goss, generally contained one or two prominent families of parallel larger-angle extended subboundaries, the traces of which on the longitudinal viewing plane appeared systematically aligned along the {111} slip plane traces, bounding long microbands subdivided into slightly elongated subgrains by short lower-angle transverse subboundaries. Relatively rare cube-orientated grains displayed pronounced subdivision into coarse deformation bands containing large, low-misorientated subgrains. The misorientation vectors across subboundaries largely showed a tendency to cluster around the sample transverse direction. Apart from the rotated Goss texture component, the stored energy levels for the remaining components were principally consistent with the corresponding Taylor factor values.

Plastic flow properties and microstructural evolution in an ultrafine-grained Al-Mg-Si alloy at elevated temperatures

An AA6082 alloy was subjected to eight passes of equal channel angular pressing at 100 °C, resulting in an ultrafine grain size of 0.2 to 0.4 µm. The tensile deformation behavior of the material was studied over the temperature range of 100 °C to 350 °C and strain rate range of 10¯⁴ to 10¯¹ s¯¹. The evolution of microstructure under tensile deformation was investigated by analyzing both the deformation relief on the specimen surface and the dislocation structure. While extensive microshear banding was found at the lower temperatures of 100 °C to 150 °C, deformation at higher temperatures was characterized by cooperative grain boundary sliding and the development of a bimodal microstructure. Dislocation glide was identified as the main deformation mechanism within coarse grains, whereas no dislocation activity was apparent in the ultrafine grains.

Mechanical properties of aged Mg-4Y-3RE alloy

This paper describes tensile properties of a peak-aged Mg-4Y·3RE alloy at room temperature to 823 K with 10^-5 - 10^-1 s^-1. The Mg alloy exhibited high strength (> 250 MPa) at room temperature to 473 K. However. the strength rapidly decreased at 573 K. It is suggested that a large decrease in strength at 573 K is attributed to grain boundary sliding. Also, elongation increased rapidly at 723 - 823 K. This is likely to arise from the relatively high strain rate sensitivity of about 0.3 due to the glide-controlled dislocation creep.

Extrusion properties of a Zr-based bulk metallic glass

The extrusion behavior of Zr_41.2Ti_13.8Cu_12.5Ni₁₀Be_22.5 metallic glasses in the supercooled liquid region was investigated. Good extrusion formability was observed under low strain rates at temperatures higher than 395 °C. The metallic glasses were fully extruded without crystallization and failure within the range of T=395–415 °C under strain rates from 5×10⁻³ s⁻¹ to 5×10⁻² s⁻¹, and the deformation behavior of the metallic glasses during the extrusion was found to be in a Newtonian viscous flow mode by a strain rate sensitivity of 1.0.

Deformation modes and anisotropy in magnesium alloy AZ31

A strongly textured sheet of magnesium alloy AZ31 has been subjected to tensile testing at temperatures between ambient and 300°C. Structures have been examined by optical and transmission electron microscopy and also by atomic force microscopy to quantify surface displacements seen at grain boundaries. Plastic anisotropy varies strongly with test temperature as was observed previously by Agnew and Duygulu. The present findings do not support the view that crystallographic <c + a> becomes a major contributor to deformation at higher temperatures. Rather, the material behaviour reflects an increasing contribution from grain boundary sliding despite the relatively high strain rate (I 0^-3 s^-1) used in the mechanical tests.

Hydrodynamic flow focusing to study the isolated effects of the flow components

Biological fluids such as blood, proteins and DNA solutiosn moving within fluidic channels can potentially be exposed to high level of shear, extension or mixed stress, either in vitro such as industrial processing of blood products or in vivo such as ocurrs in some pathological conditions. This exposure to a high level of strain can trigger some reactions. In most of the cases the nature of the flow is mixed with shear and extensional components. The ability ot isolate the effects of each component is critical in order to understand the mechanisms behind the reactions and potentially prevent them. Applying hydrodynamic flow focusing, we present in this investigation the characterization of microchannels that allow study of the regions of high shear or high extension strain rate. Micro channels were fabricated in polydimethyl siloxane (PDMS)  using standard soft-lithography techniques with a photolithographically patterned mold. Characterization of the regions with high shear and high extension strain rate is presented. Computational Fluid Dynamics (CFD) simulations in three dimensions have been carried out to gain more detailed local flow information, and the results have been validated experimentally. A comparison between the numerical models and experiment and is presented. The advantages of microfluidic flow focusing in the study  of the effects of shear and extension strain rates for biological fluids are outlined.

Post processing of the hot torsion test results using a multi-dimensional modelling approach

A model selection scheme was extended to a multi-dimensional representation of the hot torsion test torque, twist and twist rate data to calculate partial derivatives of the torque data with respect to twist and twist rate. These enabled calculation of the instantaneous strain and strain rate hardening indices in the Fields and Backofen method. The concept of an iso-parametric shape function has been borrowed from the finite element method for adding twist rate as a dependant variable to the torque-twist models identified by the model selection scheme. Expressions to calculate the hardening indices, when employing a rational model of torsion data, were derived and presented. Subsequently, the models were used for post processing the data and determining hot strength behaviour, taking into account variations of strain and strain rate hardening indices during the deformation. To substantiate the technique, the hot flow behaviour of API-X70 micro-alloyed steel was determined using a range of hot torsion test data for the material. The flow stress obtained using the instantaneous hardening indices were compared with that obtained by the orthodox technique. For the investigated cases, the onset of dynamic recrystallization (DRX) predicted by the presented technique deviated considerably from those obtained when the average indices were used.

Cross-sectional geometry of weight-bearing tibia in female athletes subjected to different exercise loadings

Summary The association of long-termsport-specific exercise loading with cross-sectional geometry of the weight-bearing tibia was evaluated among 204 female athletes representing five different exercise loadings and 50 referents. All exercises involving ground impacts (e.g., endurance running, ball games, jumping) were associated with thicker cortex at the distal and diaphyseal sites of the tibia and also with large diaphyseal cross-section, whereas the high-magnitude (powerlifting) and non-impact (swimming) exercises were not. Introduction Bones adapt to the specific loading to which they are habitually subjected. In this cross-sectional study, the association of long-term sport-specific exercise loading with the geometry of the weight-bearing tibia was evaluated among premenopausal female athletes representing 11 different sports.

Methods A total of 204 athletes were divided into five exercise loading groups, and the respective peripheral quantitative computed tomographic data were compared to data obtained from 50 physically active, non-athletic referents. Analysis of covariance was used to estimate the between-group differences.

Results At the distal tibia, the high-impact, odd-impact, and repetitive low-impact exercise loading groups had ~30% to 50% (p<0.05) greater cortical area (CoA) than the referents. At the tibial shaft, these three impact groups had ~15% to 20% (p<0.05) greater total area (ToA) and ~15% to 30% (p<0.05) greater CoA. By contrast, both the high-magnitude and repetitive non-impact groups had similar ToA and CoA values to the reference group at both tibial sites.

Conclusions High-impact, odd-impact, and repetitive lowimpact exercise loadings were associated with thicker cortex at the distal tibia. At the tibial shaft, impact loading was not only associated with thicker cortex, but also a larger cross-sectional area. High-magnitude exercise loading did not show such associations at either site but was comparable to repetitive non-impact loading and reference data. Collectively, the relevance of high strain rate together with moderate-to-high strain magnitude as major determinants of osteogenic loading of the weight-bearing tibia is implicated.

The inhibition of hydrogen embrittlement in SAE 4340 steel in an aqueous environment with the rare earth compound lanthanum 4 hydroxy cinnamate

A preliminary study showed that the inhibitor lanthanum 4-hydroxy cinnamate ((La4OHcin)₃) at a concentration of 400 ppm prevented the hydrogen embrittlement (HE) of SAE 4340 steel tensile specimens when tested under slow strain rate conditions in a 0.01M NaCl. In the presence of the inhibitor, a complex film formed on the surface of specimens during the slow strain rate test (SSRT), and no corrosion pits were detected. Electrochemical polarization studies indicated that the La(4OHcin)₃ acted as an anodic inhibitor in the NaCl solution. This article also discusses the mechanism of HE inhibition by La(4OHcin)₃.

Experimental study of dynamic compressive behaviour of concrete material reinforced with spiral steel fibres

It has been well demonstrated that the impact loading resistance capacity of the concrete material can be effectively increased by adding fibres. Recent studies proved that compared to other conventional steel fibres, using steel fibres with spiral shape further increases the post-failure energy absorption and crack stopping capacities of concrete because of the better bonds in the concrete matrix and larger deformation ability. The present study conducts high rate impact tests using split Hopkinson pressure bar (SHPB) to further investigate the dynamic compressive properties of spiral fibre reinforced concrete (SFRC). SFRC specimens with different volume fractions of fibres ranging from zero to 1.5% are prepared and tested. The influences of different volume fractions of fibres on strength, stress-strain relation and energy absorption of SFRC specimens under quasi-static and dynamic loadings are studied. In SHPB compression tests, the strain rate achieved ranges from 50 1/s to 200 1/s. Highspeed camera is used to capture the failure processes and failure modes of SFRC specimens with different fibre volume fractions during the tests for comparison. Dynamic stress-strain curves under different strain rates are derived. The energy absorption capacities of the tested specimens are obtained and compared. Strain rate effects on the compressive strength are also discussed. The corresponding empirical DIF (dynamic increase factor) relations for SFRC are proposed.

Deformation behaviour of a commercial pure titanium alloy during hot compression testing

The flow curve behaviour and microstructure evolution of commercially pure titanium (CP-Ti) through uniaxial hot compression was investigated at 850 °C and a strain rate of 0.1/s. Electron back scattered diffraction (EBSD) was employed to characterize the microstructure and crystallographic texture development for different thermomechanical conditions. The stress-strain curves of CP-Ti alloy under hot compression displayed a typical flow behaviour of metals undergoing dynamic recrystallization (DRX), which resulted in grain refinement. The critical strain for the onset of DRX was 0.13 using the double differentiation analysis technique. It was also revealed that the texture was markably altered during hot deformation. © (2014) Trans Tech Publications, Switzerland.

Microstructure evolution of martensitic Ti-6Al-4V alloy during warm deformation

The microstructure evolution of martensitic Ti-6Al-4V alloy was investigated through uniaxial hot compression at 700°C and a strain rate of 10-3 s-1. A combination of scanning electron microscopy observation in conjunction with high resolution electron back scattered diffraction (EBSD) was used to characterize the microstructure in detail. The development of the microstructure displayed continuous fragmentation of martensitic laths with increasing strain (i.e. continuous dynamic recrystallization), concurrently with decomposition of supersaturated martensite resulting in the formation of equiaxed grains. At a strain of 0.8, an ultrafine equiaxed grained structure with mostly high angle grain boundaries was successfully obtained. The current work proposes a novel approach to produce equiaxed ultrafine grains in a Ti-6Al-4V alloy through thermomechanical processing of a martensitic starting microstructure. © (2014) Trans Tech Publications, Switzerland.

The correlation between stacking fault energy and the work hardening behaviour of high-mn twinning induced plasticity steel tested at various temperatures

High-Mn Twinning Induced Plasticity (TWIP) steels have superior mechanical properties, which make them promising materials in automotive industry to improve the passenger safety and the fuel consumption. The TWIP steels are characterized by high work hardening rates due to continuous mechanical twin formation during the deformation. Mechanical twinning is a unique deformation mode, which is highly governed by the stacking fault energy (SFE). The composition of steel alloy was Fe-18Mn-0.6C-1Al (wt.%) with SFE of about 25-30 mJ/m2 at room temperature. The SFE ensures the mechanical twinning to be the main deformation mechanism at room temperature. The microstructure, mechanical properties, work hardening behaviour and SFE of the steel was studied at the temperature range of ambient ≤T[°C]≤ 400°C. The mechanical properties were determined using Instron tensile testing machine with 30kN load cell and strain rate of 10-3s-1 and the work hardening behaviour curves were generated using true stress and true strain data. The microstructure after deformation at different temperatures was examined using Zeiss Supra 55VP SEM. It was found that an increase in the deformation temperature raised the SFE resulting in the deterioration of the mechanical twinning that led to decrease not only in the strength but also in the total strain of the steel. A correlation between the temperature, the SFE, the mechanical twinning, the mechanical properties and the work hardening rate was also found. © (2014) Trans Tech Publications, Switzerland.