Compressive deformation and damage of Mg-based metallic glass interpenetrating phase composite containing 30-70 vol% titanium

Mg-based metallic glass interpenetrating phase composites (IPCs) containing 30-70 vol% titanium was fabricated in this study. The effects of reinforced phase volume fraction and interspace on the mechanical properties were investigated systematically. With increasing the volume fraction of titanium, the fracture strength and strain increased up to 1860 MPa and 44%, respectively. The results showed that the critical volume fraction (around 40%) of Ti metal should be required for significantly improving plasticity of IPC. Decreasing the interspace of the titanium phase could lead to enhancement of yield and fracture strength. The deformation behavior and strengthening mechanisms were discussed in detail.

Fracture toughness of titanium foams for medical applications

The fracture behavior of titanium open foam is characterized and the R-curves of crack propagation from pre-cracks are measured. The crack growth has been optically observed, the measured initiation toughness, J_IC, has been analyzed and the effect of material morphology on the J_IC is discussed. The fracture toughness was found to be dependent on the expanding crack bridging zone at the back of the crack tip. The compact tension specimens also have some plastic collapse along the ligaments and it has shown that the titanium foam with a higher relative density is tougher. The non-uniform stressing within the plastic zone at the crack tip and the plastic collapse of cell topology behind the tip was found to be the primary cause of the R-curve behavior in low relative density titanium foams.

In vitro osteoblast-like cell proliferation on nano-hydroxyapatite coatings with different morphologies on a titanium-niobium shape memory alloy

The morphology of nanomaterials significantly affects their physical, chemical, and biological properties. In the present study, nano-hydroxyapatite coatings with different morphologies were produced on the surface of a titanium-niobium shape memory alloy via a hydrothermal process. The effect of the nano-hydroxyapatite coatings on the in vitro proliferation of SaOS-2 osteoblast-like cells was investigated. Factors including crystallinity, surface micro-roughness, and surface energy of the nano-hydroxyapatite coatings were discussed. Results show that in vitro proliferation of the osteoblast-like cells was significantly enhanced on the nano-hydroxyapatite-coated titanium-niobium alloy compared to the titanium-niobium alloy without coating. The cell numbers on the nano-hydroxyapatite-coated titanium-niobium alloy changed consistently with the surface energy of the hydroxyapatite coatings. This study suggests that surface energy as a characteristic parameter influencing the in vitro proliferation of osteoblast-like cells was predominant over the crystallinity and surface micro-roughness of the nano-hydroxyapatite coatings.

Synthesis and characterization of silver nanoparticles and titanium oxide nanofibers : toward multifibrous nanocomposites

A new method was investigated to produce new multiscale fibrous nanocomposites comprised of titanium oxide (TiO₂) nanofibers and silver (Ag) nanoparticles (NPs). The process involved electrospinning TiO₂ precursor solution containing colloidal solution of Ag NPs, and organic solvent (dimethyl-n′n-formamide) to fabricate a porous, nonwoven, free-standing nanofiber mesh. Postprocess heating of the electrospun nanofibers entailed calcination in air environment at 500°C for 3 h. Microemulsion processing was used to generate NPs of Ag in a monodispersed distribution throughout the colloidal solution. X-ray diffraction data were consistent with the anatase phase of TiO2, while transmission electron microscopy and hydrogen desorption measurements revealed a very porous microstructure. It was demonstrated that NP colloidal stability is solvent dependent. It is anticipated that incorporation of metal particles in nanofibers will lead to enhanced photocurrent generation, when used in functional devices.

pH-detachable polymer brushes formed using titanium−diol coordination chemistry and living radical polymerization (RAFT)

pH-detachable poly(styrene) brushes formed on indium−tin oxide (ITO) glass substrates using metal complex chemistry and reversible addition−fragmentation chain transfer (RAFT) polymerization was described. These pH-detachable polymeric brushes were generated using both “graft-from” and “graft-to” methodologies. The methodologies involved either the surface self-assembly of catechol-functional RAFT agents (graft-from) or catechol-terminal polymer chains (graft-to) onto the ITO substrate via titanium−diol coordination. The stepwise functionalization of the ITO glass surfaces was characterized successfully using X-ray photoelectron spectroscopy (XPS) and contact angle measurement. Poly(styrene) brushes generated using the “graft-from” method were denser than those generated using the “graft-to” method, as exemplified by atom force microscopy (AFM) and quantified using cyclic voltammetry. Poly(styrene) brushes assembled using both methods could be detached easily by manipulating the pH of the brush environment. Cyclic voltammetry was utilized to calculate precisely the surface coverage of the RAFT functionality and polymeric brush density.

Biomechanical properties of porous metal scaffolds as implant materials

The results obtained from this work reveal that high porous titanium foams have fracture mechanical properties that meet and exceed the required properties of both cortical and cancellous bones. With their good biocompatibility, light weight, strong structural integrity and possibility of bone in-growth these foams are suitable for biomedical applications.

Nanocrystalline titanium to mesoporous anatase with high bioactivity

In present study, the formation of bioactive anatase on bulk titanium (Ti) by hybrid surface mechanical attrition treatment (SMAT) is reported. A commercial pure Ti plate first underwent SMAT in a vacuum for 1 h to produce a nanocrystalline layer with a thickness of about 30 µm, and then the nanocrystalline Ti (30 nm) was transformed into mesoporous anatase with a grain size 10 nm by chemical oxidation and calcination. The mesoporous anatase showed excellent bioactivity while being soaked in simulated body fluid, which could be attributed to the unique nanostructure on the SMAT Ti surface.

Interfacial chemistry and adhesion between titanium dioxide nanotube layers and titanium substrates

Interfacial chemistry and adhesion between titanium dioxide (TiO₂) nanotube layers and titanium (Ti) substrates were studied in this Article. TiO₂ nanotube layers were produced on pure Ti by anodization and annealed in air for different time durations. The adhesion of the TiO₂ nanotube layers was then investigated by Rockwell C indentation test. Results show that adhesion of TiO₂ nanotube layers improved with the extension of annealing time. This improvement in adhesion of TiO₂ nanotube layers was analyzed from the viewpoint of interfacial chemistry using energy dispersive X-ray spectrometry (EDS) and X-ray photoelectron spectroscopy (XPS). It suggests that more Ti-O bonds formed in the interface after annealing, and this led to the improved adhesion of the TiO₂ nanoube layers.

Thermodynamic and kinetic modelling hydrogenation of titanium particles and sheets

Use of hydrogen as a temporary alloying element in Ti alloys is an attractive approach to improve the mechanical properties of the materials, enhance processability and thereby reduce manufacturing costs. In this paper, the hydrogen diffusion process and the phase transformation both between Ti particles and in Ti sheets were simulated to analyze the mechanism of hydrogen diffusion in different phases (α-Ti, β-Ti and TiHx). With the simulation based on the kinetics and thermodynamics, quantitative behaviors of the hydrogen diffusion and the phase transformation were analyzed. The simulation results provide an insight into the diffusion process and improve the fundamental understanding of the mechanism of diffusion and phase transformation.