An organic ionic plastic crystal electrolyte based on the triflate anion exhibiting high proton transport

A novel organic ionic plastic crystal (OIPC) electrolyte based on a quaternary ammonium cation and the triflate anion has been synthesized, which shows fast proton transport and high thermal stability in the solid state when doped with triflic acid.

Ionic liquids and organic ionic plastic crystals utilizing small phosphonium cations

The development of new liquid and solid state electrolytes is paramount for the advancement of electrochemical devices such as lithium batteries and solar cells. Ionic liquids have shown great promise in both these applications. Here we demonstrate the use of phosphonium cations with small alkyl chain substituents, in combination with a range of different anions, to produce a variety of new halide free ionic liquids that are fluid, conductive and with sufficient thermal stability for a range of electrochemical applications. Walden plot analysis of the new phosphonium ionic liquids shows that these can be classed as "good" ionic liquids, with low degrees of ion pairing and/or aggregation, and the lithium deposition and stripping from one of these ionic liquids has been demonstrated. Furthermore, for the first time phosphonium cations have been used to form a range of organic ionic plastic crystals. These materials can show significant ionic conductivity in the solid state and thus are of great interest as potential solid-state electrolyte materials.

Organic ionic plastic crystal electrolytes; a new class of electrolyte for high efficiency solid state dye-sensitized solar cells

Dye-sensitized solar cells are an increasingly promising alternative to conventional silicon solar cells as a method of converting solar energy to electricity and thus providing an effectively inexhaustible energy source. However, the most efficient of these devices currently utilize liquid electrolytes, which suffer from the associated problems of leakage and evaporation. Hence, significant research is currently focused on the development of solid state alternatives. Here we report a new class of solid state electrolyte for these devices, organic ionic plastic crystal electrolytes, that allow relatively rapid diffusion of the redox couple through the matrix, which is critical to the cell performance. A range of different organic ionic plastic crystal materials, utilizing different cation and anion structures, have been investigated and the conductivities, diffusion rates and photovoltaic performance of the electrolytes are reported. The best material, utilizing the dicyanamide anion, achieves efficiencies of more than 5%.

Multimodal nanostructured titanium using severe plastic deformation

In the present study, multimodal nanostructured titanium was engineered using severe plastic deformation. The multimodal structured titanium exhibits an ultrahigh strength of over 940 MPa and a large failure elongation of 24%. The ultrahigh strength is mainly derived from the nanostructured structures; whilst the exceptional ductility originates from the large fraction of high angle grain boundaries, micro-scale structures, and the non-equilibrium grain boundary configuration. It is worth noting that apart from dislocation slip processes, the formation of deformation twins reduced the effective slip distance and increased the strain hardening capacity via the Hall-Petch mechanism, leading to high ductility of the multimodal structured titanium.

Modelling the combined effect of grain size and grain shape on plastic anisotropy of metals

Within each columnar grain of a metallic film, the resistance to dislocation glide varies in function of the orientation of the slip plane with regard to the grain long axis. Plastic slip is impeded across grain boundaries and this contributes to the anisotropy of the overall mechanical response. A simplified (Taylor-type) crystal plasticity model is proposed that accounts for such effect of grain shape on the slip system selection. Assuming that dislocation density gradients are normal to the grain boundaries, backstresses developed at the onset of plasticity are estimated based on two definitions of the effective grain boundary spacing ‘‘seen’’ by individual slip systems. The first one reduces to the mean area-to-perimeter ratio of cross-sections of the grain cut parallel to the slip plane. Closed-form expressions of the average backstresses developed inside grains with spheroidal shapes are introduced in the crystal hardening law. The model reproduces the very high plastic anisotropy of electro-deposited pure iron with a strong c-fiber and a refined columnar grain structure [Yoshinaga, N., Sugiura, N., Hiwatashi, S., Ushioda, K., Kada, O., 2008. Deep drawability of electro-deposited pure iron having an extremely sharp h111i//ND texture. ISIJ Int. 48, 667–670]. It also provides valid estimates of the texture development and the influence of grain size on the yield strength.

The biomedical application of Ti after severe plastic deformation and thermal oxidation, especially the friction and wear properties of Ti

Surface mechanical attrition treatment (SMAT), a novel surface severe plastic deformation method, was carried out for titanium (Ti) to create a gradient-structured Ti (SMAT Ti). The tribological behaviour was studied under different loads and dry sliding conditions. The results showed that the deformation layer of SMAT Ti was about 160 lm. The friction and wear results showed that the wear resistance of SMAT Ti was enhanced compared to the coarse-grained (CG) counterpart. SMAT Ti showed abrasive wear under 1 and 5 N, and exhibited abrasive and adhesive wear under 2 N. While CG Ti showed abrasive and adhesive wear under 1–2 N, and exhibited abrasive wear under 5 N for the work hardening effects.

Halogen-free chelated orthoborate ionic liquids and organic ionic plastic crystals

Five halogen-free orthoborate salts comprised of three different cations (cholinium, pyrrolidinium and imidazolium) and two orthoborate anions, bis(mandelato)borate and bis(salicylato)borate, were synthesised and characterised by DSC, X-ray diffraction and NMR. DSC measurements revealed that glass transition points of these orthoborate salts are in the temperature range from −18 to −2 °C. In addition, it was found that [EMPy][BScB] and [EMIm][BScB] salts have solid–solid phase transitions below their melting points, i.e. they exhibit typical features of plastic crystals. Salts of the bis(salicylato)borate anion [BScB]− have higher melting points compared with corresponding salts of the bis(mandelato)borate anion [BMB]−. Single crystal X-ray diffraction crystallography (for [Chol][BScB] crystals) and solid-state multinuclear (13C, 11B and 15N) NMR spectroscopy were employed for the structural characterisation of [Chol][BScB], [EMPy][BScB] and [EMIm][BScB], which are solids at room temperature: a strong interaction between [BScB]− anions and [Chol]+ cations was identified as (i) hydrogen bonding between OH of [Chol]+ and carbonyl groups of [BScB]− and (ii) as the inductive C–Hπ interaction. In the other salt, [EMIm][BScB], anions exhibit ππ stacking in combination with C–Hπ interactions with [EMIm]+ cations. These interactions were not identified in [EMPy][BScB] probably because of the lack of aromaticity in cations of the latter system. Our data on the formation of a lanthanum complex with bis(salicylato)borate in the liquid mixture of La3+(aq) with [Chol][BScB] suggest that this class of novel ILs can be potentially used in the extraction processes of metal ions of rare earth elements.

Manufacture of garment materials

Functionalizing a broad range of stretchable substrates, including synthetic and natural fabrics, fibers and non-woven materials, by coating the substrates with various materials while the substrate is held stretched so as to maintain the breathability of the materials. This provides durability to the coatings and prolonged resistance to degradation due to washing and cleaning. One or both sides of the substrate may be treated to have different functional properties. A process is also provided for materials functionalization which can be compatible with the existing equipment.