Strip twisted electrospun nanofiber yarns: Structural effects on tensile properties

Nanofiber yarns with controlled twist levels were prepared by twisting a narrow fibrous strip cut directly from electrospun nanofiber mats. The effects of fiber morphology, diameter and orientation, as well as the yarn twist level on the yarn tensile properties were examined. For the yarns made from randomly oriented fine uniform nanofibers (e.g., diameter 359 nm) and beaded nanofibers, the tensile strength increased with increasing the yarn twist level. Higher fiber diameter (e.g., 634 nm) led to the tensile strength having an initial increase and then decrease trend. The modulus increased with the twist level for all the yarns studied. However, the elongation at break increased initially with the twist level and subsequently decreased. The orientation of aligned fibers within the fiber strip greatly influenced the yarn tensile properties. When the fibers were oriented along the fiber length direction, both tensile strength and modulus were the largest.

Chemical and thermal stability of surface‐modified porous polyethylene membranes

In this paper, we describe the surface modification of porous polyethylene by the adsorption of polyelectrolyte mutilayers on plasma‐activated polyethylene surfaces. We use the migration rates of deionized water as an effective alternative to contact angle measurements in order to probe the interfacial energy of the modified surface. The newly acquired surface properties that result from the surface modification are monitored with respect to several key chemical and environmental variables. These variables were chosen so that they will reflect some of the common handling procedures in a laboratory or health care environments, such as exposure to solvents of different pH and polarities, and fluctuations of ambient temperature over an extended period, i.e., “shelf‐life” duration. The stability of these surface properties of the modified membranes is a fundamental requirement for their potential use in a variety of applications involving lateral flow and binding media for bio‐assays. In this paper, we show that a membrane modified by a polyelectrolyte monolayer is more stable than a membrane that has undergone plasma activation alone, while a membrane modified by a polyelectrolyte bilayer exhibits retention of the enhanced surface hydrophilic properties under various conditions and over a long period of time.

Clarification and concentration of sugar cane juice through ultra, nano and reverse osmosis membranes

The performance of ultrafiltration (UF) membranes with molecular weight cut off (MWCO) of 1000 and 3500 Da in clarifying sugar cane juice was investigated, as well as the performance of a nanofiltration (NF) membrane with MWCO of 200 Da and a reverse osmosis (RO) membrane in concentrating sugar cane juice. For both cases the sugar cane juice had been limed and partially clarified. The UF membranes were found to be effective at clarifying the sugar cane juice in terms of purity rise and reduction in turbidity, colour, starch and protein. A purity rise of approximately 6 was achieved by both UF membranes at trans-membrane pressures (TMP) from 15 to 25 bar. However, Brix reduction in the permeate was between 14.5 and 41.85% and 12.11 and 26.52% for 1000 Da and 3500 Da membranes respectively. For the 200 Da and RO membranes the Brix in the concentrate was increased from 7.65 to 12.3 after 3 hours of operation for the 200 Da membrane at a TMP of 10 bar, whilst the Brix in the concentrate was increased from 15.65 to 27.6 after 3 hours of operation for the RO membrane at a TMP of 35 bar. Overall, UF membranes were found to be unsuitable for clarification of sugar cane juice since significant amount of Brix is reduced in the permeate, whilst RO membranes were found to be effective for concentration of sugar cane juice.

Ag/AgCl composite nanoparticles/polyacrylonitrile nanofiber films for visible-light photocatalysis

Ag/AgCl composite nanoparticles/polyacrylonitrile nanofiber films were prepared by electrospinning and subsequent in-situ reduction combining in-situ oxidation strategy. Electrospinning was firstly used to fabricate PAN/AgNO3 composite nanofibers; then the AgNO3 was reduced by in-situ reduction with glycol; finally, an in-situ oxidation between Ag nanoparticles and FeCl3 solution was carried on to prepare the compo-site nanofiber films. The as-prepared materials can be used as high-performance photocatalysts, taking the advantage of the visible-light activity, flexibility, and high photocatalytic kinetics. The present method is helpful for the development of the high-performance membrane based photocatalysts.

Na+-doped zinc oxide nanofiber membrane for high speed humidity sensor

A novel sensitive humidity nanosensor based on Na1-doped ZnO nanofiber membrane has been prepared via electrospinning and calcination. The product was characterized by scanning electron microscopy and X-ray diffraction. During the whole relative humidity (11%–95%) measurement, the response and recovery time is about 3 and 6 s, respectively, with good linearity, and reproducibility. These remarkable and sensitive sensing performances make our product a good candidate in fabricating humidity sensors.

A study of pyrolysis conditions on carbon nanofiber properties produced from freeze-dried cellulose nanofibers

In the present work, carbon nanofibers were prepared by pyrolysis of freeze-dried cellulose nanofiber and the effect of pyrolysis conditions on the properties of carbon nanofiber was studied. SEM analysis revealed that slow heating rates below 400oC are critical to maintain the fibrous morphology after carbonization. The present study demonstrated the possibility of producing carbon nanofibers of ≤ 30 nm in diameter by a simple and scalable method.

Utilising silk fibroin membranes as scaffolds for the growth of tympanic membrane keratinocytes, and application to myringoplasty surgery

Background: Chronic tympanic membrane perforations can cause significant morbidity. The term myringoplasty describes the operation used to close such perforations. A variety of graft materials are available for use in myringoplasty, but all have limitations and few studies report post-operative hearing outcomes. Recently, the biomedical applications of silk fibroin protein have been studied. This material’s biocompatibility, biodegradability and ability to act as a scaffold to support cell growth prompted an investigation of its interaction with human tympanic membrane keratinocytes. Methods and materials: Silk fibroin membranes were prepared and human tympanic membrane keratinocytes cultured. Keratinocytes were seeded onto the membranes and immunostained for a number of relevant protein markers relating to cell proliferation, adhesion and specific epithelial differentiation. Results: The silk fibroin scaffolds successfully supported the growth and adhesion of keratinocytes, whilst also maintaining their cell lineage. Conclusion: The properties of silk fibroin make it an attractive option for further research, as a potential alternative graft in myringoplasty.

Controlling morphology and porosity of porous siloxane membranes through water content of precursor microemulsion

Here we report a facile method for controlling the morphology and porosity of porous siloxane membranes through manipulation of the water content of precursor microemulsions. The polymerizable microemulsion precursors consisted of a methacrylate-terminated siloxane macromonomer (MTSM) as the oil phase, nonionic surfactant (Teric G9A8), water, and cosurfactant (isopropanol). Photo-polymerization of the oil phase in the parent microemulsion solutions resulted in polymeric solids, and subsequent removal of the extractable components yielded porous PDMS membranes. The pre-cured parent microemulsion solutions and post-cured polymers were characterized by small angle X-ray scattering (SAXS) while the nanostructures of extracted porous polymer membranes were characterized by SAXS, scanning electron microscopy (SEM) and mercury porosimetry. The results indicated that nano- and micro-structures of the membranes could be modulated by the water content of the precursor microemulsions. Further, in situ photo-rheometry was used to follow the microemulsion polymerization process. The rate of polymerization and the mechanical properties of the resulting PDMS membranes also depend on the water content of precursor microemulsions. This study demonstrates a simple approach to the fabrication of a variety of novel porous PDMS membranes with controllable morphology and porosity.