A morphology-related study on photodegradation of protein fibres

The wool fibre has a complex morphology, consisting of an outer layer of cuticle scales surrounding an inner cortex. These two components are hard to separate effectively except by using harsh chemical treatments, making it difficult to determine the susceptibility of the different components of the fibre to photoyellowing. An approach to this problem based on mechanical fibre modification is described. To expose the inner cortex of wool to different degrees, clean wool fibres were converted into ‘powders’ of various fineness via mechanical chopping, air-jet milling, ball milling or their combination. Four types of powdered wool (samples A, B, C and D) were produced with reducing particle size distributions and an increasing level of surface damage as observed using SEM. Sample A contained essentially intact short fibre snippets and sample D contained a large amount of exposed cortical materials. Samples B and C contained a mixture of short fibre snippets and cortical materials. Solid wool discs were then compressed from the corresponding powder samples in a polished stainless steel die to enable colour measurement and UV irradiation studies. ATR-FTIR studies on powder discs demonstrated a small shift in the amide I band from 1644 cm−1 for disc A to 1654 cm−1 for disc D due to the different structures of the wool cuticle and cortex, in agreement with previous studies. Similarly an increase in the intensity ratio of the amide I to amide II band (1540 cm−1) was observed for disc D, which contains a higher fraction of cortical material at the surface of the disc.

Discs prepared from sample D appeared the lightest in colour before exposure and had the slowest photoyellowing rate, whereas discs made from powders A–C with a higher level of cuticle coverage were more yellow before exposure and experienced a faster rate of photoyellowing. This suggests that the yellow chromophores of wool may be more prevalent in cuticle scales, and that wool photoyellowing occurs to a greater extent in the cuticle than in the cortex. Photo-induced chemiluminescence measurements showed that sample D had a higher chemiluminescence intensity after exposure to UVA radiation and a faster decay rate than samples A and B. Thus one of the roles of the wool cuticle may be to protect the cortex by quenching of free radical oxidation during exposure to the UV wavelengths present in sunlight.

Properties of mechanically milled and spark plasma sintered Al–15 at.% MgB2 composite materials

Air-atomized pure aluminium powder with 15 at.% MgB₂ was mechanically milled (MMed) by using a vibrational ball mill, and MMed powders were consolidated by spark plasma sintering (SPS) to produce composite materials with high specific strength. Solid-state reactions of MMed powders have been examined by X-ray diffraction (XRD), and mechanical properties of the SPSed materials have been evaluated by hardness measurements and compression tests. Orientation images of microstructures were obtained via the electron backscatter diffraction (EBSD) technique.

The solid-state reactions in the Al–15 at.% MgB₂ composite materials occurred between the MMed powders and process control agent (PCA) after heating at 773–873 K for 24 h. The products of the solid-state reaction were a combination of AlB₂, Al₃BC and spinel MgAl₂O₄. Mechanical milling (MM) processing time and heating temperatures affect the characteristics of those intermetallic compounds. As the result of the solid-state reactions in MMed powders, a hardness increase was observed in MMed powders after heating at 573–873 K for 24 h. The full density was attained for the SPSed materials from 4 h or 8 h MMed powders in the Al–15 at.% MgB₂ composite materials under an applied pressure of 49 MPa at 873 K for 1 h. The microstructure of the SPSed materials fabricated from the MMed powders presented the bimodal aluminium matrix grain structure with the randomly distributions. The Al–15 at.% MgB₂SPSed material from powder MMed for 8 h exhibited the highest compressive 0.2% proof strength of 846 MPa at room temperature.

Synthesis of Ti–Sn–Nb alloy by powder metallurgy

The microstructural evolution and characteristics of the Ti–16Sn–4Nb powder particles and bulk alloys sintered from the powders ball-milled for various periods of time were studied. Results indicated that ball milling to 8 h led to the development of a supersaturated hcp α-Ti and partial amorphous phase due to the solid solution of Sn and Nb into Ti lattice. The bulk Ti–16Sn–4Nb alloy made from the powders ball milled for a short time, up to 2 h, exhibited a primary α and a Widmanstätten structure consisting of interlaced secondary α and β. With an increase in ball milling time up to 10 h, the microstructure evolved into a fine β phase dispersed homogeneously within α phase matrix. The microhardness values of the bulk alloy in both α- and β-phases increased with the increasing of the ball milling time and reached a plateau value at 8 h and longer, i.e. 687 and 550 HV for α- and β-phases, respectively. Likewise, the microhardness of the α phases was always higher than that of the β phases in the bulk alloys made from the powders ball milled for the same milling time.

Tailoring the photocatalytic activity of nanoparticulate zinc oxide by transition metal oxide doping

The successful use of nanoparticulate ZnO in applications such as UV-screening agents or photocatalyst for the destruction of chemical waste requires the development of techniques for controlling its photocatalytic activity. In this study, we have investigated transition metal doping as a means of achieving this goal. Powders of ZnO, Mn_xZn_1−xO, and Co_xZn_1−xO were synthesised by a three-stage process consisting of high-energy mechanical milling, heat treatment, and washing. The photocatalytic activity of these powders was evaluated using the spin-trapping technique with electron paramagnetic resonance spectroscopy. It was found that the photocatalytic activity of Co_xZn_1−xO progressively decreased with the doping level. In contrast, the activity of Mn_xZn_1−xO initially increased with doping up to a level of 2 mol% and thereafter declined. These results demonstrate that doping with transition metal oxides can be used to tailor the photocatalytic properties of nanoparticulate ZnO.

Mechanochemical synthesis of nanoparticulate ZnO–ZnWO4 powders and their photocatalytic activity

In this study, mechanochemical reaction systems with H₂WO₄ as a precursor were investigated for the synthesis of nanoparticulate powders of WO₃, ZnWO₄, and dual-phase (ZnWO₄)_x(ZnO)_1–x. The objective was to establish whether mechanochemical processing can be used to manufacture high activity photocatalysts in the ZnO–WO₃ system. Milling and heat treatment of H₂WO₄ + 12NaCl was found to result in the formation of irregularly shaped platelets of a sodium tungstate rather than nanoparticles of WO₃. Powders of single-phase ZnWO₄ and dual-phase (ZnWO₄)_x(ZnO)_1–x were successfully synthesised by incorporating H₂WO₄ into the ZnCl₂ + Na₂CO₃ + 4NaCl reactant mixture. The photocatalytic activity of these powders was evaluated using the spin-trapping technique with electron paramagnetic resonance spectroscopy. It was found that the photocatalytic activity decreased with the ZnWO₄ content. This decrease in activity was attributed to the larger average particle size of the ZnWO₄ component compared to the ZnO, which reduced the surface area available for interfacial transfer of the photogenerated charge carriers.

Effect of particle size on the photocatalytic activity of nanoparticulate zinc oxide

In this study, a three-stage process consisting of mechanical milling, heat treatment, and washing has been used to manufacture nanoparticulate ZnO powders with a controlled particle size and minimal agglomeration. By varying the temperature of the post-milling heat treatment, it was possible to control the average particle size over the range of 28–57 nm. The photocatalytic activity of these powders was characterized by measuring the hydroxyl radical concentration as a function of irradiation time using the spin-trapping technique with electron paramagnetic resonance spectroscopy. It was found that there exists an optimum particle size of approximately 33 nm for which the photocatalytic activity is maximized. The existence of this optimal particle size is attributable to an increase in the charge carrier recombination rate, which counteracts the increased activity arising from the higher specific surface area for a sufficiently small particle size.

Recent developments in mechanochemical nanoparticle synthesis

The results of recent investigations of the mechanochemical synthesis of CaC0₃, Cr₂0₃ and Nb₂0₅ nanopowders are reported. With all three materials studied, it is shown that the volume fraction of the matrix phase is crucial to the formation of separate, unagglomerated particles. With Cr₂0₃ and Nb₂0₅, amorphous particles were formed by mechanochemical reaction and low temperature heat treatment was required for crystallization. It is shown that, as a 'bottom up' process, mechanochemical processing enables the building up nanoparticles through solid-state chemical reaction in a microscopically uniform environment, leading to the formation of nanoparticles with narrow size distributions.

Mechanochemical synthesis of nanocrystalline SnO2-ZnO photocatalysts

Mechanochemical processing of anhydrous chloride precursors with Na₂CO₃ has been investigated as a means of manufacturing nanocrystalline SnO₂ doped ZnO photocatalysts. High-energy milling and heat-treatment of a 0.1SnCl₂+0.9ZnCl₂+Na₂CO₃+4NaCl reactant mixture was found to result in the formation of a composite powder consisting of oxide grains embedded within a matrix of NaCl. Subsequent washing with deionized water resulted in removal of the NaCl matrix phase and partial hydration of the oxide reaction product with the consequent formation of ZnSn(OH)₆. The extent of this hydration reaction was found to decrease in a linear fashion with the temperature of the post-milling heat-treatment over the range of 400–700 °C. For a heat-treatment temperature of 700 °C, the SnO₂ doped ZnO powder was found to exhibit significantly higher photocatalytic activity than either single-phase SnO₂ or ZnO powders that were synthesized using similar processing conditions. The heightened photocatalytic activity of the SnO₂ doped ZnO was attributed to its higher specific surface area and the enhanced charge separation arising from the coupling of ZnO with SnO₂.

Mechanochemical synthesis of nanoparticles

The results of recent investigation of the mechanochemical synthesis of inorganic nanoparticles are reviewed. It was demonstrated that, by selecting suitable chemical reaction paths, stoichiometry of starting materials and milling conditions, mechanochemical processing can be used to synthesise a wide range of nanocrystalline particles dispersed within a soluble salt matrix. Selective removal of the matrix phase by washing the resulting powder with appropriate solvents can yield nanoparticles of the desired phase. This technique has been shown to have advantages over other methods of producing nanoparticles in terms of low cost, small particle sizes, low agglomeration, narrow size distributions and uniformity of crystal structure and morphology.

Nanopowders synthesized by mechanochemical processing

The activation of chemical reactions by milling reactants in a ball mill is presented here as a novel, low cost method for the synthesis of wide range of nanopowders with mean particle sizes as small as 4 nm. The factors controlling such mechanochemical reactions are discussed with respect to their influence on particle size, size distribution, and dispersion.

Nanocrystalline zirconia powders synthesised by mechanochemical processing

Mechanochemical processing of zirconium and yttrium chloride precursors with lithium hydroxide has been used to synthesise ultrafine powders of yttria-stabilised zirconia. The precursors reacted during milling to form a composite consisting of nanocrystalline oxide grains embedded within a matrix of lithium chloride. The ultrafine powder was recovered subsequently by removing the lithium chloride through washing with deionised water and methanol. The powders were characterised using X-ray diffraction (XRD), transmission electron microscopy (TEM), and BET gas adsorption. The sintering behaviour of cold pressed pellets was examined by dilatometry.

Synthesis of ultrafine ceria powders by mechanochemical processing

The synthesis of ultrafine cerium dioxide (CeO₂) powders via mechanochemical reaction and subsequent calcination was studied. Anhydrous CeCl₃ and NaOH powders, along with NaCl diluent, were mechanically milled. A solid-state displacement reaction—CeCl₃+ 3NaOH → Ce(OH)₃+ 3NaCl—was induced during milling in a steady-state manner. Calcination of the as-milled powder in air at 500°C resulted in the formation of CeO₂ nanoparticles in the NaCl matrix. A simple washing process to remove the NaCl yielded CeO₂ particles ∼10 nm in size. The particle size was controlled in the range of ∼10–500 nm by changing the calcination temperature.

A novel approach for real mass transformation from V2O5 particles to nanorods

A solid-state, mass-quantity transformation from V2O5 powders to nanorods has been realized via a two-step approach. The nanorods were formed through a controlled nanoscale growth from the nanocrystalline V2O5 phase created by a ball milling treatment. The nanorods grow along the [010] direction and are dominated by {001} surfaces. Surface energy minimization and surface diffusion play important roles in their growth mechanism. Real large quantity production can be achieved when the annealing process is conducted in a fluidized bed which can treat large quantities of the milled materials at once. The crystal orientation of nanorods provides an improved cycling stability for lithium intercalation.

Anomalous evaporation behavior of ZnO powder milled mechanically under high-energy conditions

ZnO powder showed anomalous evaporation behavior after its mechanical milling treatment under high-energy conditions. The amount of generated vapor is about 10 times higher in the first 15 min of annealing at 1300 °C than that of unmilled ZnO powders. The strong ball impacts are responsible for the greatly enhanced evaporation ability. Low-energy ball milling involving shearing actions and rare weak impacts leads only to a small evaporation rate enhancement. The possible explanation of the high evaporation rate of the heavily milled material is the existence of large fraction of weakly bonded atoms in grain boundaries, surface defects and strained areas.

Process for the production of ultrafine plate-like alumina particles

A process for producing plate-like alumina particles with a high aspect ratio is described. Nano-sized particles of an aluminium precursor compound, optionally formed by milling, are mixed with a sufficient volume fraction of a diluent and heat treated to form substantially discrete plate-like alpha alumina particles dispersed in the diluent. A mineraliser may be added to lower the effective melting point of the system. Substantially discrete plate-like particles may be formed without agitation when the heat treatment is conducted below the melting point of the diluent.