Application of identification techniques to determine effect of carbon content in steels on rheological parameters during hot deformation

The objective of the present work is searching for the correlation between the carbon content in steels and the parameters of the rheological models, which are used to describe the materials behavior during hot plastic deformation. This correlation can be expected in the internal variable models, which are based on physical phenomena occurring in the material. Such a model, based on the dislocation density as the internal variable, is investigated in this work. The experiments including hot torsion tests are used for the analysis.
The procedure is composed of three parts. Plastometric tests were performed for steels with various carbon content. Optimization techniques were applied next to determine the coefficients in the internal variable rheological model for these steels. Two versions of the model are considered. One is based on the average dislocation density and the second accounts for the distribution of dislocation densities. Evaluation of correlation between carbon content and such coefficients in the models as activation energy for self diffusion, activation energy for recrystallization, grain boundary mobility, recovery coefficient etc. was the main objective of the work. In consequence, the model which may be used for simulation of hot forming processes for steels with various chemical compositions, is proposed.

An effective approach to grow boron nitride nanowires directly on stainless-steel substrates

When growing one-dimensional (1D) nanomaterials via the vapour–liquid–solid (VLS) model, the substrates usually need to be coated with a layer of catalyst film. In this study, however, an effective approach for the synthesis of boron nitride (BN) nanowires directly onto commercial stainless-steel foils has been demonstrated. Growth occurs by heating boron and zinc oxide (ZnO) powders at 1100 °C under a mixture of nitrogen and hydrogen gas flow (200 ml min−1). The stainless-steel foils played an additional role of catalyst besides substrate during the VLS growth of these BN nanowires. The as-synthesized nanowires emit strong photoluminescence (PL) bands at 515, 535 and 728 nm. In addition, we found that the gas flow rate and the hydrogen content in the gas mixture strongly affected the diameter and yield of the nanowires by changing the relative concentration of the nanowire growth species in the chamber.

Selective oxidation synthesis of MnCr2O4 spinel nanowires from Commercial stainless steel foil

For the first time, MnCr₂O₄ spinel single-crystalline nanowires were simply synthesized by heating commercial stainless steel foil (Cr_0.19Fe_0.70Ni_0.11) under a reducing atmosphere. The nanowires have an average diameter of 50 nm and a length of about 10 μm. Some nanowires are sheathed with a thin layer of amorphous silicon oxide. Photoluminescence measurements revealed that the nanowires exhibit an emission band at 435 nm, which resulted from the oxygen-related defects in the silicon oxide sheath. It was found that the reducing atmosphere plays a key role for the nanowire growth. In the reducing atmosphere, the Mn and Cr elements in the stainless steel could be selectively oxidized because of their higher affinity for oxygen than the Fe and Ni elements. The Fe and Ni elements in the stainless steel, however, acted as the catalyst for the vapor–liquid–solid (VLS) growth of the MnCr₂O₄ nanowires.

Recrystallization in AISI 304 austenitic stainless steel during and after hot deformation

In order to improve the understanding of the dynamic and post-dynamic recrystallization behaviours of AISI 304 austenitic stainless steel, a series of hot torsion test have been performed under a range of deformation conditions. The mechanical and microstructural features of dynamic recrystallization (DRX) were characterized to compare and contrast them with those of the post-dynamic recrystallization. A necklace type of dynamically recrystallized microstructure was observed during hot deformation at 900 °C and at a strain rate of 0.01 s⁻¹. Following deformation, the dependency of time for 50% recrystallization, t₅₀, changed from “strain dependent” to “strain independent” at a transition strain (ε^*), which is significantly beyond the peak. This transition strain was clearly linked to the strain for 50% dynamic recrystallization during deformation. The interrelations between the fraction of dynamically recrystallized microstructure, the evolution of post-dynamically recrystallized microstructure and the final grain size have been established. The results also showed an important role of grain growth on softening of deformed austenite.

Multiscale particle-in-cell modelling for advanced high strength steels

Advanced High Strength Steels (AHSS) offer outstanding characteristics for efficient and economic use of steel. The unique features of AHSS are direct result of careful heat treatment that creates martensite in the steel microstructure. Martensite and carbon content in the microstructure greatly affects the mechanical properties of AHSS, underlining more importance on microstructural discontinuities and their multiphase characteristics. In this paper, we present the Multiscale Particle-In-Cell (MPIC) method for microstructural modelling of AHSS. A specific particle method [1] usually used in fluid mechanics is adapted and implemented in a parallel multiscale framework. This multiscale method is based on homogenisation theories; with Particle-In-Cell (PIC) method in both micro and macroscale, and offers several advantages in comparison to finite element (FE) based formulation. Application of this method to a benchmark uniaxial tension test is presented and compared with conventional FE solutions.

Hot deformation and recrystallization of austenitic stainless steel: Part 11. post-deformation recrystallization

The postdeformation recrystallization behavior of a hot-deformed austenitic stainless steel was investigated based on the first part of this study, in which the microstructure development during hot deformation and, in particular, the evolution of dynamic recrystallization (DRX), was studied. The effect of different parameters such as strain, strain rate, and temperature were examined. The dependency of the time for 50 pct softening, t 50, changed from “strain dependent” to “strain independent” at a transition strain (ε*) that was in the steady-state area of the hot deformation flow curve. The fully recrystallized microstructure showed a similar transition in strain sensitivity. However, this occurred at stains greater than ε*. A mathematical model was developed to predict the transition strain under different deformation conditions. Microstructural measurements show that the transition strain corresponds to approximately 50 pct DRX in the deformed structure at the point of unloading.

Hot deformation and recrystallization of austenitic stainless steel: part 1. dynamic recrystallization

The hot deformation behavior of a 304 austenitic stainless steel was investigated to characterize the evolution of the dynamically recrystallized structure as a starting point for studies of the postdeformation  recrystallization behavior. The effect of different deformation parameters such as strain, strain rate, and temperature were investigated. The flow curves showed typical signs of dynamic recrystallization (DRX) over a wide range of temperatures and strain rates (i.e., different Zener–Hollomon (Z) values). However, under very high or very low Z values, the flow curves’ shapes changed toward those of the dynamic recovery and multiple peaks, respectively. The results showed that while DRX starts at a strain as low as 60 pct of the peak strain, a fully DRX microstructure needs a high strain of almost 4.5 times the initiation strain. The DRX average grain size showed power-law functions with both the Zener–Hollomon parameter and the peak stress, although power-law breakdown was observed at high Z values.

A descriptive model for the formation of ultrafine grained steels

This paper presents a descriptive model to explain the mechanisms involved in the development of ultrafine grained structure in steels through dynamic strain induced transformation. The model considers the microstructural evolution during and after deformation as well as the role of different process variables. A key factor is the competition between nucleation and growth, where it is shown that many potential nuclei can be lost under certain conditions leading to a mixed or coarser grain size.

Experimental and numerical investigation of low pressure tube hydroforming on 409 stainless steel

Tube hydroforming has been widely used to produce automotive structural components due to the superior properties of the hydroformed parts in terms of their light weight and structural rigidity. Compared to the traditional manufacturing process for a closed-section member including stamping and followed by welding, tube-hydro forming leads to cost savings due to reduced tooling and material handling. However, the high pressure pumps and high tonnage press required in hydroforming, lead to increased capital investment reducing the cost benefits. This study explores low pressure tube hydro forming which reduces the internal fluid pressure and die closing force required to produce the hydroformed part. The experimental and numerical analysis was for low pressure hydro formed stainless steel tubes. Die filling conditions and thickness distributions are measured and critically analysed.

Effect of pre-straining and bake hardening on the microstructure and mechanical properties of CMnSi trip steels

The effects of pre-straining and bake hardening on the mechanical behaviour and microstructural changes were studied in two CMnSi TRansformation-Induced Plasticity (TRIP) steels with different microstructures after intercritical annealing. The TRIP steels before and after pre-straining and bake hardening were characterised by X-ray diffraction, optical microscopy, transmission electron microscopy, three dimensional atom probe and tensile tests. Both steels exhibited discontinuous yielding behaviour and a significant strength increase with some reduction in ductility after pre-straining and bake hardening treatment. The following main microstructural changes are responsible for the observed mechanical behaviours: a decrease in the volume fl:action of retained austenite, a increase in the dislocation density and the formation of cell substructure in the polygonal ferrite, higher localized dislocation density in the polygonal ferrite regions adjacent to martensite or retained austenite, and the precipitation of fine iron carbides in bainite and martensite. The mechanism for the observed yield point phenomenon in both steels after treatment was analysed.

Crystallographic analysis of nano-structured bainitic steels

A 0.79C-1.5Si-1.98Mn-0.98Cr-0.24Mo-1.06Al-1.58Co (wt%) steel was isothermally heat treated at 200 and 350°C bainitic transformation temperatures. The microstructure was consisted of bainitic ferrite lath and retained austenite for both heat treatment conditions. The crystallographic analysis revealed that the bainitic ferrite laths are close to the Nishiyama-Wassermann orientation relationship with their parent austenite. The isothermal bainite transformation temperature has a significant effect on the retained austenite characteristics and the variant selection of the bainitic ferrite laths. In general, a decrease in the isothennal bainite transformation temperature refined the bainitic structure and weakened the variant selection.