Magnesium alloy applications in automotive structures

The energy absorbed by magnesium alloys (high-pressure die-cast (HPDC) AM20, AM50, AM60, and extruded AZ31) in a buckling test was significantly greater than the aluminum alloy 6061 T6 and particularly mild steel of a similar weight, but was less than that of the aluminum alloy and steel for the same thickness (Figure 6).26 This indicates that mass savings can be achieved by the substitution with magnesium alloys to achieve similar energy-absorbing characteristics.

Processing and mechanical properties of open-cell Mg alloys

Mechanical properties of open-cellular magnesium alloys with three types of
geometric cell-structures, that is, a random round cell-structure (type A). a controlled diamond cell-structure for which the angle between the struts and the load direction is 45 degree (type B) and a controlled square cell-structure for which the angle between the struts and the loading direction is 0 degree (90 degree) (type C), are investigated by compressive tests. Results indicate that type C showed a higher collapse stress than the other two types. The collapse mechanism and the effects of the loading direction on collapse stress for the three types of magnesium alloys arc discussed from the viewpoint of bending, buckling and yielding of the struts. It is suggested that collapse for the open-cellular magnesium aHoys is associated with yielding of struts

Influence of alloying additions on the extrudability of magnesium

The extrusion behaviour of a series of magnesium alloys was investigated and compared to a common aluminium alloy using limit diagrams. The variation in the limits was related to the different flow stress and solidus temperature of each alloy. The findings of this work have enabled predictions of the relative extrudability of new prototype alloys.

Low temperature formability of differently processed AZ31B magnesium alloy sheets

The research found changes in the performance (formability) of magnesium alloy sheets with a history of different processes. A key outcome found that the steel sheet metal processing of rolling and heat treatment caused a detrimental effect. The material's internal deformation was found to be linked to the poor formability.

Effect of particles on the formation of deformation twins in a magnesium-based alloy

The deformation behaviour of the age hardenable alloy Mg–5%Zn after different precipitation treatments has been examined. It has been found that during compressive deformation, fine particles increase the number of twins that form, but reduce the size and total volume fraction of twins. Visco-plastic selfconsistent modelling has been used to show that the presence of precipitates hardens the twin and prismatic slip systems more than the basal slip system. It is proposed that because the {10 ¯12} twin requires basal slip to accommodate the twinning shear, this twin type will always be hardened equal to, or more than, the basal slip system in response to precipitation.

Performance of wrought aluminium and magnesium alloy tubes in three-point bending

This present work examines the load carrying capacity, energy absorption and fracture characteristics of wrought magnesium and aluminium alloy tubes in three-point bending. Magnesium alloy AZ31, and aluminium alloys 6063 and 7075, were extruded into cylindrical tubes of both equivalent thickness and mass. A strong thickness effect was present meaning that the AZ31 tube had significantly higher load and energy absorption performance than an equivalent mass 6063 tube, albeit not as high as the 7075 tube. Hinge formation and maximum load was delayed for the magnesium alloy, meaning that a high energy absorption rate persisted to higher deformation displacements than the aluminium alloys. It was also found that fracture during deformation was dependent on the indenter diameter, tube thickness and lower support separation.

Deformation mechanisms in mg alloys and the challenge of extending room-temperature Plasticity

Magnesium alloys show promise for application in formed components where weight saving is an advantage. In most instances forming is carried out at elevated temperatures. However, there are considerable gains to be had if forming can be carried out under ambient conditions. The present article outlines some of the difficulties that lie in the way of achieving this objective. The underlying metallurgical characteristics of the issues are considered and means for overcoming them are discussed. It is concluded that a combination of microstructure and texture control remains a promising strategy.

Effect of grain size on the performance of extruded magnesium alloy tubes in three-point bending

The performance of extruded AZ31, AZ61 and AM-EX1 tubes was examined in three-point bending. Different extrusion temperatures were used to investigate the effect of grain size on the load-carrying capacity, energy absorption and fracture propensity of the tubes. Results showed that while the peak load increased with a smaller average recrystallised grain size, the retention of large elongated un-recrystallised grains in the microstructure reduced the load. The presence of the large elongated grains also appeared detrimental to the ability of the tube to deform before fracture.

Atomic scale simulation of deformation in magnesium single crystals

The deformation behaviour of magnesium single crystals under plane strain conditions has been examined using molecular dynamics modelling. The simulations were based on an existing atomic potential for magnesium taken from the literature. A strain of 10% was applied at rates of 3x10⁹s^-1 and 3x10⁷s^-1. The simulations predicted the formation of mechanical twins that accommodated extension in the c-axis direction of the hexagonal unit cell. However, the predicted twin is not of the same kind found in magnesium, but is that commonly observed in titanium. It is believed that further analysis of the physical properties predicted by this interatomic potential will shed more light on the atomic processes controlling twinning in Magnesium alloys. It also highlights the need for improvements to the interatomic potential such that more accurate deformation behaviour can be attained.

Biodegradable Mg-Ca and Mg-Ca-Y alloys for regenerative medicine

In this study, Mg-xCa (x = 0.5, 1.0, 2.0, 5.0, 10.0, 15.0 and 20.0 %, wt.%, hereafter) and Mg-1Ca-1Y alloys were investigated as new biodegradable bone implant materials. The compressive strength, ultimate strength and hardness of the Mg-Ca alloys increased, whilst the corrosion rate and biocompatibility decreased, with the increase of the Ca content in the Mg-Ca alloys; higher Ca content caused the Mg-Ca alloy to become brittle. Solutions of simulated body fluid (SBF) and modified minimum essential media (MMEM) with the immersion of Mg-xCa and Mg-1Ca-1Y alloys showed strong alkalisation. The yttrium addition to the Mg-Ca alloys does not improve the corrosion resistance of the Mg-1Ca-1Y alloy as expected compared to the Mg-1Ca alloy. It is suggested that Mg-Ca alloys with Ca additions less than 1.0 wt.% exhibited good biocompatibility and low corrosion rate.

Potentiostatic control of ionic liquid surface film formation on ZE41 magnesium alloy

The generation of potentially corrosion-resistant films on light metal alloys of magnesium have been investigated. Magnesium alloy, ZE41 [Mg−Zn−Rare Earth (RE)-Zr, nominal composition 4 wt % Zn, 1.7 wt % RE (Ce), 0.6 wt % Zr, remaining balance, Mg], was exposed under potentiostatic control to the ionic liquid trihexyl(tetradecyl)phosphonium diphenylphosphate, denoted [P_6,6,6,14][DPP]. During exposure to this IL, a bias potential, shifted from open circuit, was applied to the ZE41 surface. Electrochemical impedance spectroscopy (EIS) and chronoamperometry (CA) were used to monitor the evolution of film formation on the metal surface during exposure. The EIS data indicate that, of the four bias potentials examined, applying a potential of −200 mV versus OCP during the exposure period resulted in surface films of greatest resistance. Both EIS measurements and scanning electron microscopy (SEM) imaging indicate that these surfaces are substantially different to those formed without potential bias. Time of flight-secondary ion mass spectrometry (ToF-SIMS) elemental mapping of the films was utilized to ascertain the distribution of the ionic liquid cationic and anionic species relative to the microstructural surface features of ZE41 and indicated a more uniform distribution compared with the surface following exposure in the absence of a bias potential. Immersion of the treated ZE41 specimens in a chloride contaminated salt solution clearly indicated that the ionic liquid generated surface films offered significant protection against pitting corrosion, although the intermetallics were still insufficiently protected by the IL and hence favored intergranular corrosion processes.

The effect of potential bias on the formation of ionic liquid generated surface films on Mg alloys

An electrochemical approach to the formation of a protective surface film on Mg alloys immersed in the ionic liquid (IL), trihexyl(tetradecyl)phosphonium–bis 2,4,4-trimethylpentylphosphinate, was investigated in this work. Initially, cyclic voltammetry was used with the Mg alloy being cycled from OCP to more anodic potentials. EIS data indicate that, under these circumstances, an optimum level of protection was achieved at intermediate potentials (e.g., 0 or 0.25 V versus Ag/AgCl). In the second part of this paper, a small constant bias was applied to the Mg alloy immersed in the IL for extended periods using a novel cell design. This electrochemical cell allowed us to monitor in situ surface film formation on the metal surface as well as the subsequent corrosion behaviour of the metal in a corrosive medium. This apparatus was used to investigate the evolution of the surface film on an AZ31 magnesium alloy under a potential bias (between ±100 mV versus open circuit) applied for over 24 h, and the film evolution was monitored using electrochemical impedance spectroscopy (EIS). A film resistance was determined from the EIS data and it was shown that this increased substantially during the first few hours (independent of the bias potential used) with a subsequent decrease upon longer exposure of the surface to the IL. Preliminary characterization of the film formed on the Mg alloy surface using ToF-SIMS indicates that a multilayer surface exists with a phosphorous rich outer layer and a native oxide/hydroxide film underlying this. The corrosion performance of a treated AZ31 specimen when exposed to 0.1 M NaCl aqueous solution showed considerable improvement, consistent with electrochemical data.

"Rare Earth" texture development in extruded Mg-based alloys

This data collection addresses the problem of low ductility in magnesium alloys, preventing their wider use. It examines a series of dilute alloys in order to determine the effect of composition on the extrusion behaviour and texture, and on the room temperature tensile ductility.

An electrochemical impedance study of ionic liquid film formation and aqueous corrosion of magnesium alloy ZE41

Ionic liquid surface treatments are proposed as a method of controlling corrosion processes on magnesium alloys. An important magnesium alloy, ZE41 (nominally 4% Zn and 1% rare earth), was treated with the ionic liquid trihexyl(tetradecyl)phosphonium diphenylphosphate (P₆₆₆₁₄DPP). Impedance spectra were acquired at intervals during the treatment, indicating the development of a film and allowing a measure of the film formation process to be obtained over time. Mechanically polished and electro-polished surfaces were prepared; these surfaces, treated and untreated, were subsequently exposed to 0.1 M NaCl aqueous solutions. The corrosion behavior of the prepared surfaces were assessed using impedance spectroscopy and optical microscopy. The results indicated a significant role for the method of surface preparation used and, in both cases, the ionic liquid treatment produced a more corrosion-resistant surface.