Speed control and policing in a cellular mobile network: SpeedNet

In this paper, we describe SpeedNet, a GSM network variant which resembles an ad hoc wireless mobile network where base stations (possibly other vehicles in the network) keep track of the velocities of mobile users (cars). SpeedNet is intended to track mobile users and their speed passively for both speed policing and control of traffic. The speed of the vehicle is controlled in a speed critical zone by means of an electro-mechanical control system, suitably referred to as VVLS (vehicular velocity limiting system). VVLS is mounted in the vehicle and responds to the command signals generated by the base station. It also determines the next basestation to handoff, in order to improve the connection reliability and bandwidth efficiency of the underlying network. Robust extended Kalman filter (REKF) is used as a passive velocity estimator of the mobile user with the widely used proportional and integral controller speed control. We demonstrate through simulation and analysis that our prediction algorithm can successfully estimate the mobile users velocity with low system complexity as it requires two closet mobile-base station measurement and also it is robust against system uncertainties due to the inherent deterministic nature in the mobility model.

Location based power control for mobile devices in a cellular network

This paper provides location estimation based power control strategy for cellular radio systems via a location based interference management scheme. Our approach considers the carrier-to-interference as dependent on the transmitter and receiver separation distance and therefore an accurate estimation of the precise locations can provide the power critical mobile user to control the transition power accordingly. In this fully
distributed algorithms, we propose using a Robust Extended Kalman Filter (REKF) to derive an estimate of the mobile user’s closest mobile base station from the user’s location, heading and altitude. Our analysis demonstrates that this algorithm can successfully track the mobile users with less system complexity, as it requires measurements from only one or two closest mobile base stations and hence enable the user to transmit at the rate that is sufficient for the interference management. Our power control
algorithms based on this estimation converges to the desired power trajectory. Further, the technique is robust against system uncertainties caused by the inherent deterministic nature of the mobility model. Through simulation, we show the accuracy of our prediction algorithm and the simplicity of its implementation.

Reliable event transfer in wireless sensor networks deployed for emergency response

Sensor Networks have applications in diverse fields. They can be deployed for habitat modeling, temperature monitoring and industrial sensing. They also find application in battlefield awareness to sense chemicals and other gases used in chemical and biological warfare. An application that has become increasingly attractive in the post 9/11 era is the use of wireless sensor networks for emergency (first) response in mass casualty incidents. Reliability of data and event transfer is of critical importance to emergency response applications. In this work we propose a reliable event transfer mechanism making use of an overlay network of relay nodes. The overlay network removes the burden of data relaying from the sensor nodes and results in increasing the lifetime of the network. Simulation results prove the benefits of such an architecture. Reliability is increased 10-30% with reduction in event traffic of 60-80%.

Location based power control for energy critical sensors in a disconnected network

This paper provides a location based power control strategy for disconnected sensory nodes deployed for long term service. Power conservation is of importance particularly when sensors communicate with a mobile robot used for data collection. The proposed algorithm uses estimations from a Robust Extended Kalman Filter (REKF) with RSSI measurements, in implementing a sigmoid function based power control algorithm which essentially approaches a desired power emission trajectory based on carrier-to-interference ratios(CIR) to ensure interferenceless reception. The more realistic modelling we use incorporates physical dynamics between the mobile robot and the sensors together with the wireless propagation parameters between the transmitter and receiver to formulate a sophisticated and effective power control strategy for the exclusive usage of energy critical disconnected nodes in a sensory network increasing their life span.

Lease based addressing for event-driven wireless sensor networks

Sensor Networks have applications in diverse fields. They can be deployed for habitat modeling, temperature monitoring and industrial sensing. They also find applications in battlefield awareness and emergency (first) response situations. While unique addressing is not a requirement of many data collecting applications of wireless sensor networks it is vital for the success of applications such as emergency response. Data that cannot be associated with a specific node becomes useless in such situations. In this work we propose an addressing mechanism for event-driven wireless sensor networks. The proposed scheme eliminates the need for network wide Duplicate Address Detection (DAD) and enables reuse of addresses.

Address reuse in wireless sensor networks

Sensor Networks have applications in diverse fields. While unique addressing is not a requirement of many data collecting applications of wireless sensor networks, it is vital for the success of applications such as emergency response. Data that cannot be associated with a specific node becomes useless in such situations. In this work we propose a dynamic addressing mechanism for wireless sensor networks. The scheme enables successful reuse of addresses in event-driven wireless sensor networks. It also eliminates the need for network-wide Duplicate Address Detection (DAD) to ensure uniqueness of network level addresses.

Using mobile agents to detect node compromise in path-based DoS attacks on wireless sensor networks

Wireless sensor networks represent a new generation of real-time  embedded systems with significantly different communication constraints from the traditional networked systems. With their development, a new attack called a path-based DoS (PDoS) attack has appeared. In a PDoS attack, an adversary, either inside or outside the network, overwhelms sensor nodes by flooding a multi-hop endto- end communication path with either replayed packets or injected spurious packets. In this article, we propose a solution using mobile agents which can detect PDoS attacks easily.

Using mobile agents to detect and recover from node compromise in path-based DoS attacks in wireless sensor networks

Wireless sensor networks represent a new generation of real-time embedded systems with significantly different communication constraints from the traditional networked systems. With their development, a new attack called a path-based DoS (PDoS) attack has appeared. In a PDoS attack, an adversary, either inside or outside the network, overwhelms sensor nodes by flooding a multi-hop end-to end communication path with either replayed packets or injected spurious packets. Detection and recovery from PDoS attacks have not been given much attention in the literature. In this article, we propose a solution using mobile agents which can detect PDoS attacks easily and efficiently and recover the compromised nodes.

Maintaining optimal co-channel interference for power efficient wireless communication

Maintaining QoS (quality of service) guaranteed communication links, and improving the energy consumption; are two aspects that received a significant consideration in the modern wireless sensor network research. This paper formulates a transmission power control problem which satisfies both considerations mentioned above. Moreover, a class of functions for an iterative controller was introduced and analyzed for its convergence. The experimental evaluation of the controller justifies the theoretical assertions as well as the applicability of the control scheme in wireless nodes with minimum measurement capabilities.

Geographic routing with cooperative relaying and leapfrogging in wireless sensor networks

A novel geographic routing protocol for multi-hop wireless sensor networks is presented. It exploits the broadcast nature of the wireless channel to enable on-demand cooperative relaying and leapfrogging for circumventing weak radio links. In order to achieve energy efficiency, a metric is introduced for next-hop selection that takes into account information on the residual battery energy, the geographical position of the sensor nodes, and the channel quality of the involved radio links when available. Performance results show that the completely decentralized protocol offers significant benefits by reducing the number of (re)transmissions required to reach the destination. This translates into network-wide energy savings that extend the network lifetime.

The crossroads approach to information discovery in wireless sensor networks

Wireless sensor networks (WSN) are attractive for information gathering in large-scale data rich environments. In order to fully exploit the data gathering and dissemination capabilities of these networks, energy-efficient and scalable solutions for data storage and information discovery are essential. In this paper, we formulate the information discovery problem as a load-balancing problem, with the combined aim being to maximize network lifetime and minimize query processing delay resulting in QoS improvements. We propose a novel information storage and distribution mechanism that takes into account the residual energy levels in individual sensors. Further, we propose a hybrid push-pull strategy that enables fast response to information discovery queries.

Simulations results prove the proposed method(s) of information discovery offer significant QoS benefits for global as well as individual queries in comparison to previous approaches.

Dynamic route construction for mobile collectors in wireless sensor networks

Wireless sensor networks with mobile data collectors have been recently proposed for extending the sensor network lifetime. Powerful mobile collectors are deployed to patrol the network and approach the static sensors for collecting their data buffers using single hop communication. The route followed by the mobile collector is very crucial for the data collection operation performed in the network and highly impacts the data collection time. This paper presents a practically efficient algorithm for constructing the mobile collector route. The route is constructed dynamically during the network operational time regardless of the sensors data generation rates. The algorithm acts on minimizing the sleeping time and the number of sensors waiting for the arrival of the mobile collector. Simulation results demonstrate that the presented algorithm can effectively reduce the overall data collection time.

A practical framework for data collection in wireless sensor networks

Optimizing energy consumption for extending the lifetime in wireless sensor networks is of dominant importance. Groups of autonomous robots and unmanned aerial vehicles (UAVs) acting as mobile data collectors are utilized to minimize the energy expenditure of the sensor nodes by approaching the sensors and collecting their buffers via single hop communication, rather than using multihop routing to forward the buffers to the base station. This paper models the sensor network and the mobile collectors as a system-of-systems, and defines all levels and types of interactions. A practical framework that facilitates deploying heterogeneous mobiles without prior knowledge about the sensor network is presented. Realizing the framework is done through simulation experiments and tested against several performance metrics.

Decentralized mobility models for data collection in wireless sensor networks

Controlled mobility in wireless sensor networks provides many benefits towards enhancing the network performance and prolonging its lifetime. Mobile elements, acting as mechanical data carriers, traverse the network collecting data using single-hop communication, instead of the more energy demanding multi-hop routing to the sink. Scaling up from single to multiple mobiles is based more on the mobility models and the coordination methodology rather than increasing the number of mobile elements in the network. This work addresses the problem of designing and coordinating decentralized mobile elements for scheduling data collection in wireless sensor networks, while preserving some performance measures, such as latency and amount of data collected. We propose two mobility models governing the behaviour of the mobile element, where the incoming data collection requests are scheduled to service according to bidding strategies to determine the winner element. Simulations are run to measure the performance of the proposed mobility models subject to the network size and the number of mobile elements.

Performance of smart antennas with receive diversity in wireless sensor networks

In this paper we propose a Geometrically Based Single Bounce Elliptical Model (GBSBEM) for multipath components involving randomly placed scatterers in the scattering region with sensors deployed on a field. The system model assumes a cluster based wireless sensor network (WSN) which collects information from the sensors, filters and modulates the data and transmit it through a wireless channel to be collected at the receiver. We first develop a GBSBE model and based on this model we develop our channel model. Use of Smart antenna system at the receiver end, which exploits various receive diversity combining techniques like Maximal Ratio Combining (MRC), Equal Gain Combining (EGC), and Selection Combining (SC), adds novelty to this system. The performance of these techniques have been proved through matlab simulations and further ahead based on different number of antenna elements present at the receiver array, we calculate the performance of our system in terms of bit-error-rate (BER). Based on the transmission power we quantify for the energy efficiency of our communication model.