Solid state recycling of 5083 Al alloy by hot extrusion

The machined chips of 5083 Al alloy were recycled by hot extrusion at 723 K with an extrusion ratio of 44:1 in air. Corrosion and mechanical properties of the recycled specimens have been compared with those of a virgin extrusion which was processed from the ingot block. As a result of salt immersion tests, mass loss of the recycled specimen was not less than twice of that of the virgin extrusion. The deterioration in corrosion properties for the recycled specimen was attributed to the excessive contamination of Fe which promoted galvanic corrosion. As a result of tensile tests, the recycled specimen exhibited a good combination of high strength and high elongation to failure at room temperature. The excellent mechanical properties for the recycled specimen were attributed to the refined microstructure. However, the elongation to failure of the recycled specimen at elevated temperatures more than 573 K was lower than that of the virgin extrusion. The contamination of oxide particles is likely to be responsible for the lower elongation in the solid recycled specimen.

Cation dynamics in dimethyl-pyrrolidinium-based solid-state ion conductors

Dimethyl-pyrrolidinum-based salts have been investigated by means of DSC, conductivity, NMR and Raman spectroscopy. The investigation aims to study the effect of the anion on the behaviour of the salt, in terms of plastic properties as well as rotational degrees of freedom of the cation. The materials range from the non-plastic iodide salt to the highly plastic BF₄ salt, which flows under its own weight at elevated temperatures. The different rotational and translational motions of the cations, and the difference between rotator and plastic phases are discussed.

High mobility I− / I3− redox couple in a molecular plastic crystal: A potential new generation of electrolyte for solid-state photoelectrochemical cells

A series of new electrolyte materials based on a molecular plastic crystal doped by different iodide salts together with iodine have been prepared and characterized by thermal analysis, ionic conductivity, electrochemical and solid-state NMR diffusion measurements. In these materials, the plastic crystal phase of succinonitrile acts as a good matrix for the quaternary ammonium based iodides and iodine and appears to act in some cases as a solid-state “solvent” for the binary dopants. The materials were prepared by mixing the components in the molten state with subsequent cooling into the plastic crystalline state. This resulted in waxy-solid electrolytes in the temperature range from − 40 to 60 °C. The combination of structural variation of the cations, and fast redox couple diffusion (comparable with liquid-based electrolytes), as well as a high ionic conductivity of up to 3 × 10^{− 3} S cm^{− 1} at ambient temperature, make these materials very attractive for potential use in solid-state photoelectrochemical cells.

Rapid I−/I3− diffusion in a molecular-plastic-crystal electrolyte for potential application in solid-state photoelectrochemical cells

High current-carrying capacity and rapid, liquidlike diffusion were achieved in a dye-sensitized solar cell (DSSC) based on the plastic-crystalline electrolyte succinonitrile and the I⁻/I₃⁻ redox couple (see diagram). This could lead to the development of true solid-state DSSCs without conventional organic-liquid electrolytes, which can cause problems with long-term device stability.

Solid state NMR characterization of polyrrole : the nature of the dopant in PF6− doped films

³¹P and ¹⁹F solid state NMR have been used to study the nature of the PF₆− anion in polypyrrole films at various levels of oxidation. It appears that the symmetric PF₆− unit remains undistorted and unchanged throughout, suggesting that it is predominantly acting only as a counterion and not as a true ‘dopant’, since any distortion in the phosphorous environments would result at the very least in chemical shift anisotropy of the ³¹P nucleus. A second set of phosphorous and fluorine resonances, which are consistent with a difluoride phosphorous compound, appeared in the films. Upon electrochemical reduction of the polymer, the undistorted PF₆− anion leaves the film whereas the second phosphorous species remains. Re-oxidation of the polymer reverses the processes observed during reduction.

Solid state lithium ion conduction in pyrrolidinium imide–lithium imide salt mixtures

The properties of the binary salt system based on mixtures of methyl ethyl pyrrolidinium bis(trifluoromethane sulfonyl) imide (P₁₂) and lithium bis(trifluoromethane sulfonyl) imide (Li imide) are reported. The lithium containing mixtures were found to be more than two orders of magnitude more conductive than the parent P₁₂ phase and the 33 mol% Li imide systems showed a solid state conductivity around 1×10⁻⁴ S/cm at 20°C. This solid state conductivity is believed to take place in plastic crystal phases of the P₁₂ compound.

Composite cell components for elevated temperature all-solid-state Li-ion batteries

Application of Li-ion batteries with liquid electrolytes at elevated temperatures (above 60°C) is limited due to the decomposition of the electrolyte. Stable solid state electrolytes can solve this problem, but the conductivity of these electrolytes are relatively low, the interfacial contacts with the electrodes are poor, and the charge transfer kinetics in the electrodes are limited. Solutions for these problems by using composite electrodes and electrolytes have been investigated and the results are described. A new concept for making all-solid-state Li-ion batteries that can be applied in the temperature range between room temperature and about 150°C will be presented.

Solid state NMR characterization of lithium conducting ceramics

⁷Li solid state NMR has been used to characterize lithium aluminium titanium phosphate and lithium lanthanum titanate ceramics. Both materials have high ionic mobilities at room temperature and this is reflected in their static ⁷Li powder patterns. In the case of the phosphate based ceramic, a narrow Lorentzian peak is observed above 300 K, which narrows further with increasing temperature. The accompanying quadrupolar structure, with C_Q (quadrupolar coupling constant) ~ 40 kHz, suggests that the lithium ions are hopping rapidly between equivalent, high electric field gradient sites. The ²⁷Al and ³¹P magic angle spinning (MAS) spectra reveal an asymmetric phosphorus peak and two distinct aluminium resonances. The room temperature powder pattern of Li_0.33La_0.57TiO₃ shows a dipolar broadened peak which narrows quite suddenly at 310 K revealing quadrupolar satellites with C_Q ~ 900 Hz. A second lithium site is also observed in this material, as indicated by a further, weaker quadrupolar structure (C_Q ~ 40 kHz).

Ambient temperature plastic crystal electrolyte for efficient, all-solid-state dye-sensitized solar cell

Doping the molecular plastic crystal of succinonitrile with solid N-methyl-N-butylpyrrolidinium iodide salt and iodine has produced a highly conductive solid iodide/triiodide conductor. Furthermore, it was employed for a highly efficient, all-solid-state dye-sensitized solar cell.

Solid state actuators based on polypyrrole and polymer-in-ionic liquid electrolytes

Novel polymer-in-ionic liquid electrolytes (PILEs) have been developed for solid state electrochemical actuators based on polypyrrole. The active polymer electrodes are readily oxidized/reduced without degradation in the PILE. It was found that the actuator cycle life is significantly enhanced in the PILE as is the ‘shelf life’ of the device.

Investigation of proton dynamics and the proton transport pathway in choline dihydrogen phosphate using solid-state NMR

Choline dihydrogen phosphate has previously been shown to be a good ionic conductor as well as an excellent host for acid doping, leading to high proton conductivities required for e.g., electrochemical devices including proton membrane fuel cells and sensors. A combination of variable-temperature ¹H solid-state NMR and 2D NMR pulse sequences, including ³¹P and ¹³C CODEX and ¹H BaBa, show that the proton conduction mechanism primarily involves assisted transport via a restricted three-site motion of the phosphate unit around the P–O bond that is hydrogen bonded to the choline and exchange of protons between these anions. In other words, proton transport at ambient temperatures appears to occur most favorably along the crystallographic b axis, from phosphate dimer to dimer. At elevated temperatures exchange between the protons of the hydroxyl group on the choline cation and the hydrogen-bonded dihydrogen phosphate groups also contributes to the structural diffusion of the protons in this solid state conductor.