Fabrication of multifunctional graphene decorated with bromine and nano-Sb₂O₃ towards high-performance polymer nanocomposites

Despite great advances, it remains highly attractive but challenging to create high-performance polymeric materials combining excellent flame-retardancy and outstanding thermal, mechanical and electrical properties. We herein demonstrate a novel strategy for fabricating a multifunctional nano-additive (Br-Sb2O3@RGO) based on graphene decorated with bromine and nano-Sb2O3. Cone calorimetric tests show that incorporating 10 wt% Br-Sb2O3@RGO into thermoplastic polyurethane (TPU) strikingly prolongs the time to ignition and decreases the peak heat release rate by 72%. Besides, tensile strength and Young's modulus are enhanced by 37% and 820%, respectively. Meanwhile, the electric conductibility is increased by eleven orders of magnitude relative to the TPU matrix. This work provides a promising strategy for addressing the critical bottleneck with the existing flame retardants that only enhance flame retardancy at the expense of mechanical properties of polymeric materials. As-prepared high-performance TPU composites are expected to find many applications, especially in aerospace, tissue engineering, and cables and wires.

Precipitate characterisation of an advanced high-strength low-alloy (HSLA) steel using atom probe tomography

Increased fuel economy, combined with the need for the improved safety has generated the development of new hot-rolled high-strength low-alloy (HSLA) and multiphase steels such as dual-phase or transformation-induced plasticity steels with improved ductility without sacrificing strength and crash resistance. However, the modern multiphase steels with good strength-ductility balance showed deteriorated stretch-flangeability due to the stress concentration region between the soft ferrite and hard martensite phases [1]. Ferritic, hot-rolled steels can provide good local elongation and, in turn, good stretch-flangeability [2]. However, conventional HSLA ferritic steels only have a tensile strength of not, vert, similar600 MPa, while steels for the automotive industry are now required to have a high tensile strength of not, vert, similar780 MPa, with excellent elongation and stretch-flangeability [1]. This level of strength and stretch-flangeability can only be achieved by precipitation hardening of the ferrite matrix with very fine precipitates and by ferrite grain refinement. It has been suggested that Mo [3] and Ti [4] should be added to form carbides and decrease the coiling temperature to 650 °C since only a low precipitation temperature can provide the precipitation refinement [4]. These particles appeared to be (Ti, Mo)C, with a cubic lattice and a parameter of 0.433 nm, and they were aligned in rows [4]. It was reported [4] that the formation of these very fine carbides led to an increase in strength of not, vert, similar300 MPa. However, the detailed analysis of these particles has not been performed to date due to their nanoscale size. The aim of this work was to carry out a detailed investigation using atom probe tomography (APT) of precipitates formed in hot-rolled low-carbon steel containing additions Ti and Mo.

The investigated low-carbon steel, containing Fe–0.1C–1.24Mn–0.03Si–0.11Cr–0.11Mo–0.09Ti–0.091Al at.%, was produced by hot rolling. The processing route has been described in detail elsewhere [5] European Patent Application, 1616970 A1, 18.01.2006.[5]. The microstructure was characterised by transmission electron microscopy (TEM) on a Philips CM 20, operated at 200 kV using thin foil and carbon replica techniques. Qualitative energy dispersive X-ray spectroscopy (EDXS) was used to analyse the chemical composition of particles. The atomic level of particle characterisation was performed at the University of Sydney using a local electrode atom probe [6]. APT was carried out using a pulse repetition rate of 200 kHz and a 20% pulse fraction on the sample with temperature of 80 K. The extent of solute-enriched regions (radius of gyration) and the local solute concentrations in these regions were estimated using the maximum separation envelope method with a grid spacing of 0.1 nm [7]. A maximum separation distance between the atoms of interest of dmax = 1 nm was used.

The microstructure of the steel consisted of two types of fine ferrite grains: (i) small recrystallised grains with an average grain size of 1.4 ± 0.2 μm; and (ii) grains with a high dislocation density (5.8 ± 1.4 × 1014 m−2) and an average grain size of 1.9 ± 0.1 μm in thickness and 2.7 ± 0.1 μm in length (Fig. 1a). Some grains with high dislocation density displayed an elongated shape with Widmanstätten side plates and also the formation of cells and subgrains (Fig. 1a). The volume fraction of recrystallised grains was 34 ± 8%.

The effect of resistance training on functional capacity and quality of life in individuals with high and low number of metabolic risk factors

OBJECTIVE—There are limited data on the effects of resistance training on the capacity to perform activities of daily living (ADLs) and quality of life (QoL) for individuals with a high number of metabolic risk factors (HiMF). In this study, we examined the effect of resistance training on the capacity to perform ADLs and QoL in individuals with HiMF and compared any benefits with individuals with a low number of metabolic risk factors (LoMF).

RESEARCH DESIGN AND METHODS—Fifty-five untrained individuals, aged 50.8 ± 6.5 years, were randomized to four groups: HiMF training (HiMFT), HiMF control, LoMF training (LoMFT), and LoMF control. At baseline and after 10 weeks of resistance training, participants underwent anthropometric measurements and assessments of aerobic power (Vo2peak), muscle strength, capacity to perform ADLs, and a self-perceived QoL questionnaire. A repeated-measures ANOVA was used to examine the effect of training over time among groups.

RESULTS—Training increased lean body mass in both HiMFT (P = 0.03) and LoMFT (P = 0.03) groups. Total fat content and Vo2peak improved in the LoMFT group only. Muscle strength improved in both training groups (P < 0.01). Time to complete ADLs was reduced by 8.8% in the LoMFT group (P < 0.01) and 9.7% in the HiMF group (P < 0.01). Only the HiMFT group reported improvement in QoL.

CONCLUSIONS— Resistance training improved muscle strength and the capacity to perform ADLs in individuals with HiMF and LoMF. Resistance training improved QoL for the HiMF group, and this result was independent of changes in body fat content or aerobic power. Longer training regimens may be needed to improve QoL in individuals with LoMF.

Effect of manufacturing process on the final properties of advanced high strength steels for automotive applications

The performance of multiphase steels with high strength and improved toughness or ductility, such as intercritically annealed dual-phase (DP) and transformation-induced plasticity (TRIP) steels, is of key importance to the automotive industry. In this work we have considered the entire manufacturing process and the effects of this on the final product performance. These steels are formed to produce the required final shape and then the car is paint baked. In this work we also consider the effect of cold working and bake hardening on the fatigue life of the components.

Microstructures and properties of ferrite/bainite dual-phase steels with high hole-expanding ratio

The effects of Si and Mn contents on microstructure, mechanical properties and formability of low carbon Si-Mn steels were studied, and the crack propagation of ferrite/bainite dual-phase steel was also investigated. The results showed that the increase in Si content increases the volume fraction of equiaxed ferrite. However, the increase in Mn content increases both strength and ductility, but decreases elongation and hole-expanding ratio. The crack of ferrite/bainite dual-phase steel is formed by the mode of microvoid coalescence. When a microcrack meets the bainite, it mostly propagates along the phase interface between ferrite and bainite and by cutting off ferrite grains. The hot-rolled ferrite/bainite dual-phase steel, which has a hole-expanding ratio of 95% and good property combination, could be produced by designing proper contents of Si and Mn as well as parameters of TMCP.

Strain hardening behavior of high performance FBDP, TRIP and TWIP steels

Based on n-value differential equation and microstructural observation, strain hardening behaviors of FBDP, TRIP, and TWIP steels during uniaxial tension were investigated. TRIP steel exhibits both superior strength and ductility than FBDP steel, and TWIP steel displays much higher total and uniform elongations in comparison to FBDP and TRIP steels. The instantaneous n values of FBDP and TRIP steels increase at small strains, reach a maximum value, smoothly decrease at higher strains, and then rapidly drop up to the specimen rupture. The strain hardening of TRIP steel persists at higher strains where that of FBDP steel begins to diminish. TWIP steel exhibits gradually increased instantaneous n values over the whole uniform plastic deformation, implying that TWIP steel shows a much larger strain hardening capability than FBDP and TRIP steels.

Fabrication, microstructure and mechanical properties of high performance ferrite-bainite steels

Low cost ferrite and bainite(FB) steels offer the prospect of high ultimate tensile strength combined with high hole expansion ratio. The enhanced strain hardening and formabilityof FB steels were primarily associated with the fine ferrite matrix, the low residual stresses and dislocation densityand compatible deformation between both phases.This overview describes the various techniques to produce FB steels, and comparestheresulting microstructure, tensile propertiesand tretchflangeabilitywith conventional HSLA and DP steels.A new generation of ultrafine ferrite and nano-scalebainiteautomotive steelsisunder development forthe futuredemands of extremely high strength and ductilitythroughthe fabricationtechnologiesinvolvingphase transformationsandplastic deformation.

Impact of nanodiffusion on the stacking fault energy in high-strength steels

A key requirement of modern steels – the combination of high strength and high deformability – can best be achieved by enabling a local adaptation of the microstructure during deformation. A local hardening is most efficiently obtained by a modification of the stacking sequence of atomic layers, resulting in the formation of twins or martensite. Combining ab initio calculations with in situ transmission electron microscopy, we show that the ability of a material to incorporate such stacking faults depends on its overall chemical composition and, importantly, the local composition near the defect, which is controlled by nanodiffusion. Specifically, the role of carbon for the stacking fault energy in high-Mn steels is investigated. Consequences for the long-term mechanical properties and the characterisation of these materials are discussed.

A first step towards a simple in-line shape compensation routine for the roll forming of high strength steel

The roll forming process is increasingly used in the automotive industry for the manufacture of structural and crash components from Ultra High Strength Steel (UHSS). Due to the high strength of UHSS (<1GPa) even small and commonly observed material property variations from coil to coil can result in significant changes in material yield and through that affect the final shape of the roll formed component. This requires the re-adjustment of tooling to compensate for shape defects and maintain part geometry resulting in costly downtimes of equipment. This paper presents a first step towards an in-line shape compensation method that based on the monitoring of roll load and torque allows for the estimation of shape defects and the subsequent re-adjustment of tooling for compensation. For this the effect of material property variation on common shape defects observed in the roll forming process as well as measurable process parameters such as roll load and torque needs to be understood. The effect of yield strength and material hardening on roll load and torque as well as longitudinal bow is investigated via experimental trials and numerical analysis. A regression analysis combined with Analysis of Variance (ANOVA) techniques is employed to establish the relationships between the process and material parameters and to determine their percentage influence on longitudinal bow, roll load and torque. The study will show that the level of longitudinal bow, one of the major shape defects observed in roll forming, can be estimated by variations in roll load and torque.

High-intensity resistance training improves glycemic control in older patients with type 2 diabetes

OBJECTIVE -- To examine the effect of high-intensity progressive resistance training combined with moderate weight loss on glycemic control and body composition in older patients with type 2 diabetes.

RESEARCH DESIGN AND METHODS -- Sedentary, overweight men and women with type 2 diabetes, aged 60-80 years (n = 36), were randomized to high-intensity progressive resistance training plus moderate weight loss (RT & WL group) or moderate weight loss plus a control program (WL group). Clinical and laboratory measurements were assessed at 0, 3, and 6 months.

RESULTS -- HbA._1c fell significantly more in RT & WL than WL at 3 months (0.6 ± or -] 0.7 vs. 0.07 ± 0.8%, P < 0.05) and 6 months (1.2 ±1.0 vs. 0.4 ±0.8, P < 0.05). Similar reductions in body weight (RT & WL 2.5 ±2.9 vs. WL 3.1±2.1 kg) and fat mass (RT & WL 2.4 ± 2.7 vs. WL 2.7±2.5 kg) were observed after 6 months. In contrast, lean body mass (LBM) increased in the RT & WL group (0.5 ±1.1 kg) and decreased in the WL group (0.4±1.0) after 6 months (P < 0.05). There were no between-group differences for fasting glucose, insulin, serum lipids and lipoproteins, or resting blood pressure.

CONCLUSIONS -- High-intensity progressive resistance training, in combination with moderate weight loss, was effective in improving glycemic control in older patients with type 2 diabetes. Additional benefits of improved muscular strength and LBM identify high-intensity resistance training as a feasible and effective component in the management program for older patients with type 2 diabetes.

Preparation and characterisation of new titanium based alloys for orthopaedic and dental applications

Various types of titanium alloys with high strength and low elastic modulus and, at the same time, vanadium and aluminium free have been developed as surgical biomaterials in recent years. Moreover, porous metals are promising hard tissue implants in orthopaedic and dentistry, where they mimic the porous structure and the low elastic modulus of natural bone. In the present study, new biocompatible Ti-based alloy foams with approximate relative densities of 0.4, in which Sn and Nb were added as alloying metals, were synthesised through powder metallurgy method.
The new alloys were prepared by mechanical alloying and subsequently sintered at high temperature using a vacuum furnace. The characteristics and the processability of the ball milled powders and the new porous titanium-based alloys were characterised by X-ray diffraction, optical
microscopy and scanning electron microscopy .The mechanical properties of the new titanium alloys were examined by Vickers microhardness measurements and compression testing.

Eri silk fibre attributes and sliver preparation

Eri silk produced by Philosamia cynthia ricini silkworm is a fibre not well-known to the silk industry, in spite of the fact that Eri silk is finer, softer, and has better mechanical and thermal properties than most animal fibres. Eri silk has a high commercial potential, as the host plants of Eri silk worms are widespread in diverse geographical locations, and the worms also have a higher degree of disease resistance than most other silk worms. Mills are often not aware of the properties of Eri for designing appropriate end products. Thus, Eri silk yarn is traditionally produced by hand spinning, and Eri silk usually ends up as material for handwoven shawls. The potential for bulk fibre processing and the development of soft luxurious novel Eri silk products is yet to be discovered. To better understand the material and its processing behaviour, Eri silk was characterised and cocoons were processed into tops through degumming, opening, and cutting filaments into different lengths, followed by a worsted spun silk processing route. Fibre properties such as fineness, crimp, strength and length at different processing stages up to combed tops were measured. The results indicate that staple Eri silk can be processed via the worsted topmaking route, using a cut length of 200 mm or 150 mm for filament sheets prepared from degummed cocoons.

What determines migration flows from low-income to high-income countries? An empirical investigation of Fiji-U.S. migration 1972-2001

This article examines the long-run and short-run determinants of migration from Fiji to the United States between 1972 and 2001 using a human capital framework, which is extended to take account of political instability in Fiji. In the long-run the authors find that differences in income levels, disparities in police strength, disparities in the number of doctors, costs of moving, and political instability in Fiji are all statistically significant with the expected sign. In the short run the cost of moving, lagged migration, political instability, and differences in both police strength and medical care are the main determinants of Fiji-United States immigration.

High performance mg alloy by grain refinement

Mg alloys are one of promising eco-materials. The present paper describes the importance of grain refinement to develop high performance Mg alloys. The fine-grained Mg alloys exhibit not only a good combination of high strength and high ductility at room temperature, but also high formability (superplasticity) at elevated temperatures.

Moderate-intensity resistance exercise training in patients with chronic heart failure improves strength, endurance, heart rate variability, and forearm blood flow

Thirty-nine CHF patients (New York Heart Association Functional Class = 2.3±0.5; left ventricular ejection fraction 28%±7%; age 65±11 years; 33:6 male:female) underwent 2 identical series of tests, 1 week apart, for strength and endurance of the knee and elbow extensors and flexors, VO_2peak, HRV, FBF at rest, and FBF activated by forearm exercise or limb ischemia. Patients were then randomized to 3 months of resistance training (EX, n = 19), consisting of mainly isokinetic (hydraulic) ergometry, interspersed with rest intervals, or continuance with usual care (CON, n = 20), after which they underwent repeat endpoint testing. Combining all 4 movement patterns, strength increased for EX by 21±30% (mean±SD, P<.01) after training, whereas endurance improved 21±21% (P<.01). Corresponding data for CON remained almost unchanged (strength P<.005, endurance P<.003 EX versus CON). VO_2peak improved in EX by 11±15% (P<.01), whereas it decreased by 10±18% (P<.05) in CON (P<.001 EX versus CON). The ratio of low-frequency to high-frequency spectral power fell after resistance training in EX by 44±53% (P<.01), but was unchanged in CON (P<.05 EX versus CON). FBF increased at rest by 20±32% (P<.01), and when stimulated by submaximal exercise (24±32%, P<.01) or limb ischemia (26±45%, P<.01) in EX, but not in CON (P<.01 EX versus CON).