A 7Li and 19F NMR relaxation study of LiCF3SO3 in plasticised solid polyether electrolytes

⁷Li and ¹⁹F NMR relaxation time (T₁, T₂, T_1ρ) measurements have been used to probe the dynamics of LiCF₃SO₃ dissolved in an amorphous co-polymer poly(ethylene oxide-co-propylene oxide), and in particular the influence of the plasticising agents propylene carbonate and dimethyl formamide. The changes in relaxation behaviour of ¹⁹F and ⁷Li with increasing plasticiser concentration are very different, as is the effect of each plasticiser. These differences can be explained qualitatively in terms of the interaction between the plasticiser and the ions. Preliminary ⁷Li T_1ρ measurements reveal two components at low temperatures.

Transport properties of ionic liquid electrolytes with organic diluents

Ionic liquids (ILs) form a novel class of electrolytes with unique properties that make them attractive candidates for electrochemical devices. In the present study a range of electrolytes were prepared based on the IL N-methyl-N-propylpyrrolidinium bis(trifluoromethylsulfonyl) amide ([C₃mpyr][NTf₂]) and LiNTf2 salt. The traditional organic solvent diluents vinylene carbonate (VC), ethylene carbonate (EC), tetrahydrofuran (THF) and toluene were used as additives at two concentrations, 10 and 20 mol%, leading to a ratio of about 0.6 and 1.3 diluent molecules to lithium ions, respectively. Most promisingly, the lithium ions see the greatest effect in the presence of all the diluents, except toluene, producing a lithium self-diffusion coefficient of almost a factor of 2.5 times greater for THF at 20 mol%. Raman spectroscopy subtly indicates that THF may be effectively breaking up a small portion of the lithium ion–anion interaction. While comparing the measured molar conductivity to that calculated from the self-diffusion coefficients of the constituents indicates that the diluents cause an increase in the overall ion clustering. This study importantly highlights that selective ion transport enhancement is achievable in these materials.

Microscopic interactions in nanocomposite electrolytes

Nanocomposite electrolytes of a fully amorphous trifunctional polyether (3PEG) and poly- (methylene ethylene oxide) (PMEO) have been complexed with two lithium salts and nanoparticulate (~20 nm) fillers of TiO2 and Al2O3. Addition of the fillers to the polymer salt complexes shows a significant change in the conformational modes of both polymers, especially the D-LAM region between 200 and 400 cm-1, indicating a reduced segmental flexibility of the chain. These changes are more pronounced with the use of TiO2 than Al2O3. Incorporation of the nanoparticulate fillers to the electrolytes fails to influence the degree of ion association, suggesting that the number of charge carriers available for conduction in both polymers using both LiClO4 and LiCF3SO3 is not the source of any conductivity increase. Addition of the fillers, which was seen to increase the conductivity in PEO-based systems, generally lowers the conductivity in the present PMEO systems, while the addition of TiO2 has little or no effect except in the cases of 3PEG 1.5 and 1.25 mol/kg LiClO4. In this case, 10 wt % TiO2 provides a conductivity increase of half an order of magnitude at approximately 60 °C. We also report for the first time a Raman spectroscopy investigation into the PEO-based nanocomposite electrolytes. The present results are discussed in terms of the electrostatic interactions involving dielectric properties of the fillers, of special interest being the interactions between the polymer and the fillers and between the ionic species and the fillers, when the effect of crystallization can be ignored.

Ion association and molar conductivity in polyether electrolytes

The ion association behaviour observed in our earlier studies of a polyether electrolyte system at elevated temperatures, was reminiscent of the molar conductivity behaviour typical of low dielectric constant systems. Further investigation of this relationship has led to some suggestions about the types of ionic species present in the polymer electrolyte systems. FT-IR spectroscopy has been used in this work to contrast ion association in an amorphous polyether electrolyte with two liquid electrolytes, N,N-dimethyl-formamide and tetraethylenegylcol dimethylether, containing lithium trifluoromethan sulfonate.

FT-IR investigation of Ion association in plasticized solid polymer electrolytes

FT-IR spectroscopy has been utilized to monitor ion association in plasticized solid polymer electrolytes (SPEs). The SPEs were prepared from a random copolymer of ethylene oxide (EO) and propylene oxide (PO) and the salt lithium trifluoromethanesulfonate (lithium triflate, LiTf). Tetraethylene glycol dimethyl ether (tetraglyme) and N,N‘-dimethylformamide (DMF) were chosen as model plasticizers. Despite having a similar dielectric constant to that of the polymer host, ε ~ 5, the incorporation of tetraglyme into the SPEs resulted in increased ion association. The addition of a higher dielectric constant solvent , DMF, ε = 36.7, resulted in decreased ion association in the SPE. The effects of salt concentration (0.05−1.25 mol dm^-3) and temperature (25−100 °C) upon ion association in SPEs were also investigated. At low salt concentrations, ion association was found to increase with temperature, however, at 1.25 mol dm^-3 the temperature dependence of ion association was dominated by concentration effects. There appears to be a maximum in the fraction of “free” ions at a LiCF₃SO₃ concentration of 0.4 mol dm^-3, preceded by a minimum at approximately 0.2 mol dm^-3, consistent with the molar conductivity behavior previously observed in these electrolytes.

Triflate ion association in plasticized polymer electrolytes

Ion association in plasticised solid polymer electrolytes (SPEs) has been monitored using FT-IR spectroscopy. The SPEs were prepared from a random co-polymer of ethylene oxide (EO) and propylene oxide (PO) and the salt lithium trifluoromethane sulfonate (lithium triflate, LiTf). Tetraethylene glycol dimethylether (tetraglyme, ε˜5) and N,N'-dimethyl formamide (DMF, ε = 36.7) were chosen as model plasticisers. Decreased ion association resulted from plasticization with DMF, indicating that the addition of a higher dielectric constant solvent increases the fraction of dissociated ions in the SPE. The incorporation of tetraglyme into these SPEs results in increased ion association, despite the similar dielectric constants of the plasticiser and polymer host. The effects of salt concentration (0.05–1.25 mol dm^{− 3} solvent) upon ion association in SPEs was also investigated. There appears to be a minimum in the number of “free” ions at a LiTf concentration of 0.2 mol dm^{− 3} solvent followed by a maximum at approximately 0.4 mol dm^{− 3} solvent, consistent with the molar conductivity behaviour previously observed in these electrolytes.

Ionic conductivity studies of polymeric electrolytes containing lithium salt with plasticizer

New plasticized polymer electrolytes were synthesized based on poly ethylene oxide (PEO), Poly (N,N-dimethylamino-ethyl-methacrylate) (PDMAEMA), LiN(CF₃SO₂)₂ (LITFSI) as the salt and tetraethylene glycol dimethyl ether(tetraglyme) and EC + PC as plasticizers. The preparation and characterization of the polymer electrolytes were investigated as a function of temperature and various concentrations of LITFSI. Impedance spectroscopy and differential scanning calorimeter (DSC) were used to characterize the effects of various temperature, lithium salt concentration and two plasticizers on conductivity. The complex of PDMAEMA/PEO/LiTFSI/tetraglyme (S2) exhibits higher conductivity (4.74 × 10⁻⁴ S cm⁻¹at 25 °C) than PDMAEMA/PEO/LiTFSI/EC + PC (S1).

Dye-sensitized nanocrystalline solar cells incorporating ethylmethylimidazolium-based ionic liquid electrolytes

High-performance dye-sensitized solar cells incorporating electrochemically stable non-volatile electrolytes are especially desirable devices. In particular, ionic liquid systems based on ethylmethylimidazolium dicyanamide seem to be promising for this purpose. These have triggered our interest in the properties of further ethylmethylimidazolium-based ionic liquids with anions which are close relatives of dicyanamide. In this study, the effect of three different anions, tricyanomethanide, dicyanamide and thiocyanate, on the performance of dye-sensitized solar cells have been investigated. Both the short circuit photocurrent and conversion efficiency are increased with decreasing viscosity of the ionic liquids under comparable conditions. A conversion efficiency of 2.1% at 30% light intensity was observed for the cell containing the tricyanomethanide salt, which has lowest viscosity among the three ionic liquids, while efficiencies of 0.7% and 1.7% at the same light intensity were observed in the case of dicyanamide and thiocyanate salts, respectively, as an electrolyte.

Lithium ion mobility in poly(vinyl alcohol) based polymer electrolytes as determined by 7Li NMR spectroscopy

Solvent-free polymer electrolytes based on poly(vinyl alcohol) (PVA) and LiCF₃SO₃ have shown relatively high conductivities (10⁻⁸-10⁻⁴ S cm⁻¹), with Arrhenius temperature dependence below the differential scanning calorimeter (DSC) glass transition temperature (343 K). This behaviour is in stark contrast to traditional polymer electrolytes in which the conductivity reflects VTF behaviour. ⁷Li nuclear magnetic resonance (NMR) spectroscopy has been employed to develop a better understanding of the conduction mechanism. Variable temperature NMR has indicated that, unlike traditional polymer electrolytes where the linewidth reaches a rigid lattice limit near T_g, the lithium linewidths show an exponential decrease with increasing temperature between 260 and 360 K. The rigid lattice limit appears to be below 260 K. Consequently, the mechanism for ion conduction appears to be decoupled from the main segmental motions of the PVA. Possible mechanisms include ion hopping, proton conduction or ionic motion assisted by secondary polymer relaxations.

NMR determination of ionic structure in plasticized polyether-urethane polymer electrolytes

Solid polymer electrolytes based on amorphous polyether-urethane networks combined with lithium or sodium salts and a low molecular weight cosolvent (plasticizer) have been investigated in our laboratories for several years. Conductivity enhancements of up to two orders of magnitude can be obtained whilst still retaining solid elastomeric properties. In order to understand the effects of the plasticizers and their mechanism of conductivity enhancement, multinuclear NMR has been employed to investigate ionic structure in polymer electrolyte systems containing NaCF₃SO₃, LiCF₃SO₃ and LiClO₃ salts.

With increasing dimethyl formamide (DMF) and propylene carbonate (PC) concentration the increasing cation chemical shift with fixed salt concentration indicates a decreasing anion-cation association consistent with an increased number of charge carriers. ¹³C chemical shift data for the same systems suggests that whilst DMF also decreases cation-polymer interactions, PC does the opposite, presumably by shielding cation-anion interactions. Temperature dependent ⁷Li spin-lattice relaxation times indicate the expected increase in ionic mobility upon plasticization with a shift of the T₁ minimum to lower temperatures. The magnitude of T₁ at the minimum increases upon addition of DMF whereas there is a slight decrease when PC is added. This also supports the suggestion that the DMF preferentially solvates the cation whereas the action of PC is limited to coulomb screening, hence freeing the anion.

Novel high salt content polymer electrolytes based on high Tg polymers

Conductivities greater than or equal to 10⁻⁸ S cm⁻¹ at T_g are reported in polymer electrolytes based on lithium triflate salt and a series of polymers whose T_g is greater than 90°C. The highest conductivities were observed for poly(acrylonitrile) based systems with salt concentrations greater than 60 wt.%. The conductivity in all cases investigated increases with increasing salt concentration. ¹H-NMR T₂ relaxation measurements suggest that T_g decreases with increasing salt content and confirms that these materials are glassy at room temperature and hence that the conductivity is significantly decoupled from the structural relaxations. It appears that the nature of the polymer is important in determining the level of ionic conductivity, possibly due to differences in polymer coordinating ability or differences in T_g. Polymer-in-salt mixtures based on a tetra-alkyl ammonium imide molten salt and several high T_g polymers are also reported. The conductivities of these mixtures appear to be independent of the polymer type.

The effect of nano-particle TiO2 fillers on structure and transport in polymer electrolytes

Nano-particle oxide fillers including TiO₂, SiO₂ and Al₂O₃ have previously been shown to have a significant affect on the properties of polymer electrolytes, especially those based on polyether–lithium salt systems. In some cases, conductivity increases of more than one order of magnitude have been reported in crystalline PEO-based complexes. In this work, we report on the effects of TiO₂ on a completely amorphous polyether-based system to remove the complication of multiple phases presented by the semi-crystalline nature of PEO. Multinuclear magnetic resonance spectroscopy has shown that the lithium ion environment is changed by the addition of filler. Vibrational spectroscopy shows that the filler influences the disordered-longitudinal acoustic modes (DLAM) in the case of an amorphous polyether and suggests an interaction between the filler surface and the polymer. Positron annihilation lifetime spectroscopy indicates an increase in free volume upon addition of filler to an amorphous polyether–salt complex, coinciding with an apparent increase in polymer mobility as determined from ¹H T₂ NMR measurements. Impedance spectroscopy has shown clear evidence of an inter-phase region that may be more or less conductive than the bulk polymer electrolyte itself. The data support a model which includes conduction through an interfacial region in addition to the bulk polymer