Comparison of bending of automotive steels in roll forming and in a V-die

Bending in a V-die has been used to indicate the outcome of bending in cold roll forming, although little direct correlation has been performed. In this work direct comparison of the springback in both processes was performed using six samples of automotive steels in a conventional roll forming line where the transverse springback is measured. A bend of similar radius was formed in a V-die and the springback determined. In general, the springback in V-die forming was greater than in roll forming, in some cases by a factor of 2. The theoretical springback angle was determined for all steels using a simple and approximate analytical equation and compared to the experimental roll forming and bending results. While for the roll forming process good agreement was achieved the theoretical values significantly underestimated springback in the V-bending process.

Practical amine functionalization of multi-walled carbon nanotubes for effective interfacial bonding

 Improved methods of functionalizing the surfaces of multi-walled carbon nanotubes (MWCNTs) have been investigated. It is shown that a level of primary amines of 2.3%, higher than previously reported for any nitrogen-containing gas plasma treatment, can be achieved using a mixture of N2 and H2, which is preferable to using NH3. Even higher levels (3.5%) of primary amines can be achieved by coating the MWCNTs with a thin layer of plasma polymerized heptylamine. In both cases, the highest levels were achieved using a combined continuous plus pulsed plasma mode which was superior to either continuous wave or pulsed wave alone. The integrity of the MWCNT structure is maintained by the plasma treatments, and the functionalized surface improves the dispersion of the MWCNTs and their interfacial bonding with epoxy, giving superior nanoindentation performance of the composites.

Improved bonding and conductivity of polypyrrole on polyester by gaseous plasma treatment

A systematic study was conducted using argon, oxygen, and nitrogen plasma to improve the adhesion of polypyrrole coating to polyester (PET) fabric for improving conductivity and to understand the mechanisms involved. PET thin film was used as a reference sample. The changes in wettability, surface chemistry and morphology were studied by water contact angle, X-ray photoelectron spectroscopy, and atomic force and scanning electron microscopy. It was found that both the highest conductivity and the strongest interfacial bonding were achieved by oxygen plasma treatment. The increase in hydrophilicity, surface functionalization, and suitable nano-scale roughness gave improved adhesion.

Nanostructured block copolymer blends and complexes via hydrogen bonding interactions

This thesis investigates the influence of hydrogen bonding interactions on the self-assembly, phase behaviour and nanostructures of the block copolymer/homopolymer systems. The different combinations of block copolymer blends and complexes of AB/C, AB/CD, and ABC/D mixtures open a convenient way to tailor various morphologies with controlled size and shape.

Roll forming cryo-rolled nano-structured aluminium sheet

Commercial purity aluminium plate was reduced by rolling under nitrogen in 30 passes from an initial material thickness of 10 mm to a final thickness of 2 mm (80% reduction). Analysis of the microstructure showed that the material produced in this way had an ul-trafine grained microstructure. The sheet was roll formed at room temperature to a V-section using commercial roll forming equipment. Two sets of experiments were per-formed; one with a 15 mm radius in the base of the V and the other with a 5 mm radius. The performance in terms of final shape and springback is compared with the same part shape formed by V-die bending. The mechanical properties of the sheet were determined using the tensile test. It has been found that even if the total tensile elongation is close to zero and bending of the material is very limited, ultra-fine grained and low ductile sheet metals can be roll formed to simple section shapes.

Approach for testing the material behavior in roll forming in a small scale

Roll forming of ultra-high strength steels (UHSS) and other high strength alloys is an advanced manufacturing methodology with the ability of cold forming those materials to complex three-dimensional shapes for lightweight structural applications. Due to their high strength, most of these materials have a reduced ductility which excludes conventional sheet forming methods under cold forming conditions. Roll forming is possible due to its low strains and incremental forming characteristic. Recent research investigates the development of high strength nano-structured aluminum sheet and titanium alloys, as well as their behaviour in roll forming with regard to formability, material behaviour and shape defects. The development of new materials is often limited to small scale samples due to the high preparation costs. In contrast, industrial application needs larger scale tests for validation, especially in roll forming where a minimum sheet length is required to feed the sample trough the roll forming machine. This work describes a novel technique for studying roll forming of a short length of experimental material. DP780 steel strips (500mm – 1300mm length) were welded between two mild steel carrier sheets of similar width and thickness giving an overall strip length of 2m. Roll forming trials were performed and longitudinal edge strain, bow and springback determined on the welded samples and samples formed of full length DP780 strip before and after cut off. The experimental results of this work show that this method gives a reasonable approach for predicting material behavior in roll forming transverse to the rolling direction. In contrast to that significant differences in longitudinal bow were observed between the welded sections and the sections formed of full length DP780 strip; this indicates that the applicability of this method is limited with regard to predicting longitudinal material behavior in roll forming.

Asymmetric rolling of interstitial-free steel using differential roll diameters. Part I : mechanical properties and deformation textures

IF steel sheets were processed by conventional symmetric and asymmetric rolling (ASR) at ambient temperature. The asymmetry was introduced in a geometric way using differential roll diameters with a number of different ratios. The material strength was measured by tensile testing and the microstructure was analyzed by optical and transmission electron microscopy as well as electron backscatter diffraction (EBSD) analysis. Texture was also successfully measured by EBSD using large surface areas. Finite element (FE) simulations were carried out for multiple passes to obtain the strain distribution after rolling. From the FE results, the velocity gradient along selected flow lines was extracted and the evolution of the texture was simulated using polycrystal plasticity modeling. The best mechanical properties were obtained after ASR using a roll diameter ratio of 2. The textures appeared to be tilted up to 12 deg around the transverse direction, which were simulated with the FE-combined polycrystal plasticity modeling in good agreement with measurements. The simulation work revealed that the shear component introduced by ASR was about the same magnitude as the normal component of the rolling strain tensor.

How do drug and alcohol use relate to parental bonding and risk perception in university students?

Alcohol and drug use are major health concerns on university and college campuses. It has previously been found that parental rearing patterns are related to the frequency of substance use. Further, perceptions that drug use is dangerous have been found to be related to less substance use. However, little research has directly examined the impact of parental rearing patterns on substance use by university students, and no research has examined the effects of both risk perception and parenting on substance use. Therefore, this research surveyed the frequency and extent of alcohol, cigarette and illicit drug use by students (N = 336) at a Canadian university residence, classes and health services and examined the relationship between the results with parental bonding and risk perception. It was found that “affectionless control” parenting patterns in the mother, but not the father, were related to greater drinking and drinking problems and to the use of illicit substances. Lower perceptions of risk were related to greater use of alcohol, cigarettes, cannabis and other illicit substances. Unexpectedly, there was little relationship between parental rearing and risk perceptions, suggesting that there are other avenues whereby parenting leads to greater alcohol use. Implications are discussed.