Study on the dyeing properties of hemicyanine dyes. I. Acrylic fabrics

Three hemicyanine dyes were employed in dyeing acrylic fabrics following traditional cationic dyeing procedures. The influence of the substituting groups of the dye molecule on the sorption rate and sorption isotherms was analyzed. The results showed that those dyed acrylic fabrics using hemicyanine dyes had obvious fluorescent effect in the spectra range 550–750 nm. In addition, according to the EN-471 standard (2003), the chromaticity of dyed acrylic fabric was calculated to evaluate whether hemicyanine dye could meet the requirements of the fluorescent dye for high visibility warning clothing.

Improving knowledge, fibre and textile quality, and communications

This is a technical report summarising activities to improve the knowledge about rare natural animal fibres in Australia, including aspects of their production, fibre quality, and textiles made from these fibres. It summarises results of Australian investment on these subjects, and makes recommendations about future investment. This is important, as there is limited scientific understanding of how to improve productivity, quality and financial returns from these industries in Australia.

Potential of textile hemp in biomedical and composite applications

The fabrication of hemp fine powder was documented for the first time. The antibacterial properties of hemp powders and hemp plant extracts from textile hemp were investigated for the first time. Fabrication and characteristics of hemp powder blended polypropylene polymer composite filaments were investigated for the first time.

Performance comparison of abrasion resistant textile motorcycle clothing

 Falling at speed onto a tarmac surface during cycling can cause abrasion and laceration of the skin and body tissue. Motorcycle clothing designed to reduce or avoid this type of injury has traditionally been made of animal leather as it has well known resistance to abrasion. In the last 20 years there has been an emergence of textile clothing reinforced with high performance/tenacity fibres such as those made from polyamides, aramids, ultra high molecular weight polyethylene and liquid crystal. Almost no comparative work has been undertaken to provide insight into the level of protection these clothing layers can provide.
This work has used a CE standard test method to evaluate a number of abrasion resistant textile pant products and compare them with a leather race product. It analysed the protective fabric layer structure for mass, thickness, construction method and resistance to abrasion.
Structures manufactured from high tenacity fibres performed better than those from lower tenacity ones. Fabric construction method and mass per unit area were the two key variables in providing an abrasion protective layer. Structures manufactured from knitted para-aramid fibres performed better than their woven counterparts due to the method of fabric failure. Several well designed protective layers performed at a similar level to that of leather; however, most garments tested failed to meet the lower level European standard of abrasion resistance (CE level 1), which may put their wearer at risk in the advent of a collision.

Template-free synthesis of functional 3D BN architecture for removal of dyes from water.

Three-dimensional (3D) architectures are of interest in applications in electronics, catalysis devices, sensors and adsorption materials. However, it is still a challenge to fabricate 3D BN architectures by a simple method. Here, we report the direct synthesis of 3D BN architectures by a simple thermal treatment process. A 3D BN architecture consists of an interconnected flexible network of nanosheets. The typical nitrogen adsorption/desorption results demonstrate that the specific surface area for the as-prepared samples is up to 1156 m(2) g(-1), and the total pore volume is about 1.17 cm(3) g(-1). The 3D BN architecture displays very high adsorption rates and large capacities for organic dyes in water without any other additives due to its low densities, high resistance to oxidation, good chemical inertness and high surface area. Importantly, 88% of the starting adsorption capacity is maintained after 15 cycles. These results indicate that the 3D BN architecture is potential environmental materials for water purification and treatment.

Comparison between nanofiltration and forward osmosis in the treatment of dye solutions

Colour removal and the flux behaviour of nanofiltration (NF-DOW FILMTEC-NF245) and forward osmosis (FO-a flat sheet cellulose triacetate membrane with a woven embedded backing support) membranes were investigated in this study. The NF membrane was employed to perform dye removal experiments with aqueous solutions containing 15 g/L of NaCl and different concentrations of Acid Green 25, Remazol Brilliant Orange FR and Remazol Blue BR dyes. The increase in dye concentration resulted in a decline in water permeability and an increase in colour removal. When the concentrations of dye solutions varied from 250 to 1000 mg/L, at 0.8 bar of trans-membrane pressure, the NF system exhibited a steady permeate flux of more 30 L/m2h and a colour removal of more than 99%; salt rejection was more than 20.0%. Furthermore, the FO system possessed high dye rejection efficiency (almost 100%), with low permeate flux of around 2.0 L/m2h, when using dye solutions as feed streams and seawater as draw stream. The mode of operation (either FO or pressure retarded osmosis (PRO) did not change the flux significantly but PRO mode always produced higher fluxes than FO mode under the operating conditions used in this study. While both NF and FO can be used to reduce the volume of effluent containing dyes from textile industries, the energy spent in NF on applied pressure can be substituted by the osmotic pressure of draw solution in FO when concentrated draw solutions such as sea water or reverse osmosis concentrate are readily available.

Selective removal of anionic dyes using poly (N, N -dimethyl amino ethylmethacrylate) functionalized graphene oxide

An in situ polymerization strategy was used to functionalize graphene oxide (GO) with poly(N,N-dimethyl amino ethylmethacrylate) (PDMAEMA) for the selective removal of anionic dyes. Various characterization methods demonstrate that PDMAEMA-grafted GO (GO-PDMAEMA) was successfully synthesized, and the high PDMAEMA content of 68.5% in GO-PDMAEMA changed the zeta potential significantly from -36.5 (GO) to 41.5 (GO-PDMAEMA). This change in the charge of GO-PDMAEMA greatly increased the adsorption capacities for anionic dye orange G (OG) compared to the pristine GO. The maximum adsorption capacity for anionic OG dye based on the Langmuir model is 609.8 mg g-1. The adsorption mechanism is believed to be a consecutive process of intra-particle diffusion and surface adsorption, with electrostatic interactions as the key driving force. The GO-PDMAEMA nanocomposite also showed excellent regeneration capacity and selectivity towards the separation of various anionic dyes (i.e. OG, Eosin yellow and Congo red) from an aqueous dye mixture. In conclusion, our method offers a promising strategy for developing new anionic dye adsorbents.