Do maternally derived antibodies and early immune experience shape the adult immune response?

1. Immunological imprinting by maternally derived antibodies has been proposed to have both positive and negative consequences for offspring immunity in early and adult life. However, few studies of maternal effects on immunity have followed individuals past the juvenile stages.

2. Using laboratory Japanese quail, we developed a novel method of directly manipulating yolk antibodies of neonates, and then followed individuals through a series of immune challenges until they were of reproductive age.

3. Our method of directly injecting purified antibodies into the yolk sac of newly hatched chicks successfully elevated the plasma titres of specific anti-KLH IgY in neonates. This allows us to test whether differences in neonatal anti-KLH IgY affect immunity at the juvenile and adult stages of life.

4. We found little evidence for an effect of maternal antibodies on juvenile stage immune response, in contrast to results from previous studies. Adult immune response depended largely on the magnitude of the juvenile immune response regardless of the identity of the antigen in the juvenile immune challenge, and did not depend on neonatal IgY titres. Our results are consistent with a priming effect of early immune experience on adult stage immune responsiveness, but we found no evidence of carryover effects of yolk-derived antibodies on adult immunity.

5. This study employs new methodology for investigation of maternal antibodies and presents results suggesting that further studies of maternal effects on immunity will require careful consideration of the numerous ways maternally derived yolk components can impact the different types of immune response.

Thermo-mechanical processing and the shape memory effect in an Fe–Mn–Si-based shape memory alloy

The effect of cold rolling and annealing on the shape memory effect (SME) in an Fe–Mn–Si-based alloy has been studied. It has been found
that the SME in these alloys can be significantly increased by the appropriate thermo-mechanical processing (TMP). The optimum conditions
were found to be 15% cold rolling followed by annealing at 800 ◦C for 15 min. This produced a total strain recovery of 4.5%. TEM showed that
this processing schedule produces a microstructure of evenly spaced, and well defined stacking faults throughout the parent phase. It is shown for
the first time that samples processed in this way produce a larger fraction of martensite compared to samples in the as-austenitized condition. It
is concluded that the stacking faults induced by TMP act as nucleation sites for martensite formation during deformation. The SME is improved
primarily as a result of the increased amount of martensite that is formed in this condition.

Effect of NbC and TiC precipitation on shape memory in an iron-based alloy

This paper examines the effects of TiC and NbC precipitation and prior cold rolling on the shape memory behaviour of an iron-based alloy. A precipitate-free alloy was used as a reference to investigate the relative contributions of prior-deformation and precipitation on shape memory. Heat treatment of the Nb- and Ti-containing alloys at 700 °C and 800 °C resulted in carbide precipitates between 120 nm and 220 nm in diameter. Bend testing of these samples showed a marginal increase in shape memory compared to the precipitate-free alloy. Under these conditions TiC precipitation exhibited slightly better shape memory than for NbC. However, this small increase was over-shadowed by the marked increase in shape memory that can be produced by subjecting the alloys to cold rolling followed by recovery annealing. When processed in this way, fine carbides are formed in the Ti- and Nb-containing alloys during the heat treatment. For particles >25 nm in diameter the shape memory is unaffected, but, it was found that small <5 nm particles have a detrimental effect on shape memory due to pinning of the martensite plates, thereby inhibiting their reversion to austenite. The optimum shape memory was observed in the precipitate-free alloy after cold rolling and recovery annealing.

Optimization of alloy design and hot rolling conditions for shape memory in Fe–Mn–Si-based alloys

The effect of composition and hot rolling conditions on the shape memory effect (SME) in the Fe–Mn–Si-based system has been studied to obtain improved shape memory without the need to rely on “training”. It has been found that the texture is not markedly affected by rolling conditions, and texture is therefore not a major factor in explaining variations in SME with processing conditions. Decreasing the pre-deformation temperature to below the Ms was found to have a beneficial effect on shape memory. It was found that the best SME was achieved in an alloy that had Ms just above room temperature, and had been processed by hot rolling followed by recovery annealing. Alloys of different compositions exhibited different optimum rolling temperatures for maximum shape memory performance.

Effect of second-phase particles on shape memory in Fe-Mn-Si-based alloys

The shape memory behaviour of two Fe–Mn–Si-based alloys has been investigated. One alloy was a reference alloy, and the other alloy was
similar in composition except that it contained 0.55 wt% Ti. Following solution treatment and quenching, strip samples were subjected to three types
of treatments; isothermal holding, cold rolling followed by isothermal holding, and hot rolling followed by isothermal holding. These treatments
resulted in the formation of intermetallic precipitates in the Ti-containing alloy, while the reference alloy remained precipitate-free. In comparing
the shape memory of the reference and the particle-containing alloy after identical heat treatments, it was found that the formation of precipitates
had a beneficial effect on the shape memory in all cases. In general, the larger precipitates caused a larger increase in the shape memory. The effect
of particle size on shape memory has been analysed using the current data and published results for a range of precipitate types.

Martensite/particle interactions and the shape memory effect in an Fe–Mn–Si-based alloy

The effect of carbide precipitates with a size range of 30–300 nm on the austenite to martensite transformation has been studied. Such particles are known to enhance shape memory, and it was the aim of this work to clarify how the particles exert a favourable effect on shape memory. Differential scanning calorimetry revealed that the presence of particles increases the amount of thermally induced martensite. X-ray diffraction showed that the presence of particles increases the amount of stress-induced martensite also. Surface-relief produced on a pre-polished surface by bending deformation showed that the particle-containing samples exhibited a more complex and highly tilted surface-relief indicative of the formation of a larger volume fraction of martensite. The reversion characteristics of the particle-containing and solution-treated samples were similar: both showed co-reversion of multiple variants of martensite within the same volume of microstructure. However, a higher volume fraction of martensite reverted for the particle-containing sample on recovery annealing. The increased density of nucleation sites for martensite formation and a higher volume fraction of stress-induced martensite for a given strain are therefore considered to be the main contributions of relatively coarse carbide particles to the improvement of shape memory performance.

Austenite stability in Fe-Mn-Si-based shape memory alloys

The stability of austenite in a number of Fe–Mn–Si-based shape memory alloys has been investigated. It was found that a grain boundary precipitate of BCC structure is formed over a wide range of alloy compositions and heat treatment temperatures. This grain boundary phase has been identified as the chi (χ) phase. Although up to 3 vol.% of the grain boundary precipitate was generated by isothermal aging in the range 500–800 °C, it was found not to markedly affect the mechanical properties or the shape memory effect. Nano-indentation indicated that the hardness and strength of the parent and precipitate phase are very similar, as are their compositions.

Drawing lines in the sea : the laws that govern traffic on the world’s oceans can be as difficult to shape as water

Since World War II, however, the term has increasingly referred to law enforcement operations, as a means to enforce trade sanctions, to prevent the movement of weapons of mass destruction (WMDs), and particularly in the Caribbean Sea, to prevent the smuggling of illicit drugs. Such ambiguity should allow flexibility when deciding whom should be targeted, as well as allowing states with veto powers in the UN Security Council, which may legitimately ship nuclear weapons and materials, to avoid being targeted as long as they do not export WMDs to rogue states or non-state groups or individuals.2 The ISPS Code was created under the auspices of the International Maritime Organization (IMO) and is part of the 1974 Safety of Life at Sea Convention (SOLAS) concerning the safety of merchant ships.

The development of young adolescent boys' weight and shape concerns

This thesis' longitudinal study found that young adolescent boys' reported significant concerns with their weight and shape, particularly with respect to having a more muscular but lean physique. The strongest predictors of high body dissatisfaction, among boys, were poor perceptions of their sporting ability and low self-esteem. The portfolio examines the use of Single Session Therapy (SST) suggesting that SST can effectively reduce waiting lists and provide a single and complete intervention that is effective in approximately 50% of cases.

Children's liking and wanting of snack products : influence of shape and flavour

Background : Children's food choices are guided by their preferences. However, these preferences may change due to repeated exposure.

Methods : This study investigated children's (n = 242, 7–12 yrs-old) liking and wanting for snacks over 3 weeks of daily consumption. The snacks differed in size (small vs large) or flavour (sweet vs sweet-sour). Two conditions were designed: 1) a monotonous group in which children continuously consumed the same snack across the 3 weeks, and 2) a free choice group in which children were allowed to freely choose amongst 3 different flavours of the snack each day during 3 weeks.

Results : Shape influenced long-term liking, i.e. small shaped snacks remained stable in liking over repeated consumption, whereas large shaped snacks with the same flavour decreased in liking. Mean wanting ratings for all snack products decreased over 3 weeks daily consumption. Flavour did not significantly influence liking and wanting over time. The ability to freely choose amongst different flavours tended to decrease children's liking (p < 0.1) and wanting (p < 0.001) for these products. Changes in liking rather than initial liking was the best predictor of snack choice during the intervention.

Conclusion : Wanting rather than liking was most affected by repeated daily consumption of snack foods over three weeks. In order to increase the likelihood that children will repeatedly eat a food product, smaller sized healthy snacks are preferred to larger sized snacks. Future research should focus on stabilizing wanting over repeated consumption.

Design of a new biocompatible ti-based shape memory alloy and its superelastic deformation behaviour

Titanium-nickel (Ti-Ni) shape memory alloys have been widely used for biomedical applications in recent years. However, it is reported that Ni is allergic and possibly carcinogenic for the human body. Therefore, it is desirable to develop new Ni-free Ti-based shape memory alloys for biomedical applications. In the present study, a new Ti-18Nb-5Mo-5Sn (wt.%) alloy, containing only biocompatible alloying elements, was designed with the aid of molecular orbital method and produced by vacuum arc melting. Both β and α″ martensitic phases were found to coexist in the alloy after ice-water quenching, indicating the martensitic transformation. The phase transformation temperatures of the Ti-18Nb-5Mo-5Sn alloy were M_s = 7.3 °C, M_f = −31.0 °C, A_s = 9.9 °C, and A_f = 54.8 °C. Superelasticity was observed in the alloy at a temperature higher than the A_f temperature. A totally recovered strain of 3.5 % was achieved for the newly designed Ti-based shape memory alloy with a pre-strain of 4 %.

Porous shape memory alloy scaffolds for biomedical applications : a review

The interest in using porous shape memory alloy (SMA) scaffolds as implant materials has been growing in recent years due to the combination of their unique mechanical and functional properties, i.e. shape memory effect and superelasticity, low elastic modulus combined with new bone tissue ingrowth ability and vasculariszation. These attractive properties are of great benefit to the healing process for implant applications. This paper reviews current state-of-the art on the processing, porous characteristics and mechanical properties of porous SMAs for biomedical applications, with special focus on the most widely used SMA nickel-titanium (NiTi), including (i) microstructural features, mechanical and functional properties of NiTi SMAs; (ii) main processing methods for the fabrication of porous NiTi SMAs and their mechanical properties and (iii) new-generation Ni-free, biocompatible porous SMA scaffolds.

Titanium-based shape memory alloys and scaffolds for biomedical applications

Porous Ti-50.5Ni shape memory alloys with different porosities were produced using a space-holder sintering method. A new Ni-free Ti-based shape memory alloy, Ti-18Nb-5Mo-5Sn, was developed for potential biomedical applications, and a novel one-step hydrothermal process was applied to produce hydroxyapatite coatings on the surface of Ti alloy.

Novel spectral descriptor for object shape

In this paper, we propose a novel descriptor for shapes. The proposed descriptor is obtained from 3D spherical harmonics. The inadequacy of 2D spherical harmonics is addressed and the method to obtain 3D spherical harmonics is described. 3D spherical harmonics requires construction of a 3D model which implicitly represents rich features of objects. Spherical harmonics are used to obtain descriptors from the 3D models. The performance of the proposed method is compared against the CSS approach which is the MPEG-7 descriptor for shape contour. MPEG-7 dataset of shape contours, namely, CE-1 is used to perform the experiments. It is shown that the proposed method is effective.